that it is better to error out when people attempt to build using the
wrong bsd.*.mk files, than to silently ignore the problem.
This means, that after this commit, if you want to build kernel modules
by hand (or via a port) from a head source tree, you *must* make sure
the files in /usr/share/mk are in sync with that tree. If that isn't
possible, for example when you are running on an older FreeBSD branch,
you can:
- Run "make buildenv" from your head source tree, to have the correct
environment setup. (It's advisable to have run "make buildworld", or
at a minimum "make toolchain" first.)
- Alternatively, set MAKESYSPATH to the share/mk directory under your
head source tree. If your build tools are too old, other problems may
still occur.
- Alternatively, use "make -m" and specify the share/mk directory under
your head source tree. Again, build tools that are too old may still
result in trouble.
MFC after: 2 weeks
kernel modules using their old installed /usr/share/mk/bsd.*.mk files,
instead of the updated ones in their source tree. This leads to errors
like:
"sys/conf/kmod.mk", line 111: Malformed conditional (${MK_CLANG_IS_CC} == "no" && ${CC:T:Mclang} != "clang")
Obviously, these errors will go away after a "make installworld", or
alternatively, by using "make buildenv" before attempting to manually
build modules.
However, since it is apparently an expected use case to build using old
.mk files, change the way we test for clang, so it also works when the
MK_CLANG_IS_CC macro doesn't exist.
Note the conditional expressions are becoming rather unreadable now, but
I will attempt to fix that on a followup commit.
MFC after: 2 weeks
- Document the following routines: pci_alloc_msi(), pci_alloc_msix(),
pci_find_cap(), pci_get_max_read_req(), pci_get_vpd_ident(),
pci_get_vpd_readonly(), pci_msi_count(), pci_msix_count(),
pci_pending_msix(), pci_release_msi(), pci_remap_msix(), and
pci_set_max_read_req().
- Group the functions into five sub-sections: raw configuration access,
locating devices, device information, device configuration, and
message signaled interrupts.
- Discourage use of pci_disable_io() and pci_enable_io() in device drivers.
The PCI bus driver handles this automatically as resources are activated.
MFC after: 2 weeks
interface supported by mvs(4) are 88SX, while AHCI-like chips are 88SE.
PR: kern/165271
Submitted by: Jia-Shiun Li <jiashiun@gmail.com>
MFC after: 1 week
not ACPI-specific at all, but deal with PCI power states. Also,
pci_set_powerstate() fails with EOPNOTSUPP if a request is made that the
underlying device does not support rather than falling back to somehow
setting D0.
pci_cfg_save() and pci_cfg_restore() for device drivers to use when
saving and restoring state (e.g. to handle device-specific resets).
Reviewed by: imp
MFC after: 2 weeks
installs clang as /usr/bin/cc, /usr/bin/c++ and /usr/bin/cpp.
Note this does *not* disable building and installing gcc, which will
still be available as /usr/bin/gcc, /usr/bin/g++ and /usr/bin/gcpp. If
you want to disable gcc completely, you must use WITHOUT_GCC.
MFC after: 2 weeks
get rid of testing explicitly for clang (using ${CC:T:Mclang}) in
individual Makefiles.
Instead, use the following extra macros, for use with clang:
- NO_WERROR.clang (disables -Werror)
- NO_WCAST_ALIGN.clang (disables -Wcast-align)
- NO_WFORMAT.clang (disables -Wformat and friends)
- CLANG_NO_IAS (disables integrated assembler)
- CLANG_OPT_SMALL (adds flags for extra small size optimizations)
As a side effect, this enables setting CC/CXX/CPP in src.conf instead of
make.conf! For clang, use the following:
CC=clang
CXX=clang++
CPP=clang-cpp
MFC after: 2 weeks
USERSPACE:
1. add support for devices with different number of rx and tx queues;
2. add better support for zero-copy operation, adding an extra field
to the netmap ring to indicate how many buffers we have already processed
but not yet released (with help from Eddie Kohler);
3. The two changes above unfortunately require an API change, so while
at it add a version field and some spares to the ioctl() argument
to help detect mismatches.
4. update the manual page for the two changes above;
5. update sample applications in tools/tools/netmap
KERNEL:
1. simplify the internal structures moving the global wait queues
to the 'struct netmap_adapter';
2. simplify the functions that map kring<->nic ring indexes
3. normalize device-specific code, helps mainteinance;
4. start exploring the impact of micro-optimizations (prefetch etc.)
in the ixgbe driver.
Use 'legacy' descriptors on the tx ring and prefetch slots gives
about 20% speedup at 900 MHz. Another 7-10% would come from removing
the explict calls to bus_dmamap* in the core (they are effectively
NOPs in this case, but it takes expensive load of the per-buffer
dma maps to figure out that they are all NULL.
Rx performance not investigated.
I am postponing the MFC so i can import a few more improvements
before merging.
- Remove all attempts to guess physical temperature using DiodeOffset.
There are too many reports that it varies wildly depending on motherboard.
Instead, if it is known to scale well and its offset is known from other
temperature sensors on board, the user may set "dev.amdtemp.0.sensor_offset"
tunable to compensate the difference. Document the caveats in amdtemp(4).
- Add a quirk for Socket AM2 Revision G processors. These processors are
known to have a different offset according to Linux k8temp driver.
- Warn about Family 10h Erratum 319. These processors have broken sensors.
- Report temperature in more logical orders under dev.amdtemp node. For
example, "dev.amdtemp.0.sensor0.core0" is now "dev.amdtemp.0.core0.sensor0".
- Replace K8, K10 and K11 with official processor names in amdtemp(4).
- Convert to our standard SYNOPSIS language
- Consistently use "The .Nm driver"
- Rewrite .nf .fi block with mdoc
- Add pci dependency to SYNOPSIS
- Start .Bl list with new paragraph
Approved by: luigi
1. Add new functionality to the force_depend method to incorporate the
tests for whether the service is enabled and/or already running.
2. Add a new option to bypass checking only that the service is enabled
at boot time, and always check if it is running.
3. Use this new functionality to greatly simplify the rc.d scripts that
use force_depend.
4. Add a force_depend for statd in lockd
5. Remove the check that either nfs_server or nfs_client is _enable'd
from statd and lockd. This was always overkill, and prevented using
the {one|force}start options, as well as stop'ing on the command line.
6. The yp* scripts had some of their arguments in various weird orders.
Bring them into line with the model.
7. If mountd fails to create /var/db/mountdtab, err out.
Ideas, suggestions, and/or review from delphij and jilles.
Pointy hats are completely my responsibility however.
The reasoning behind this, is that if we are consistent in our
documentation about the uint*_t stuff, people will be less tempted to
write new code that uses the non-standard types.
I am not going to bump the man page dates, as these changes can be
considered style nits. The meaning of the man pages is unaffected.
MFC after: 1 month
Add support for updating the devfs mount (currently only changing the
ruleset number is supported).
Check mnt_optnew with vfs_filteropt(9).
This new option sets the specified ruleset number as the active ruleset
of the new devfs mount and applies all its rules at mount time. If the
specified ruleset doesn't exist, a new empty ruleset is created.
MFC after: 1 month
side effect of something else using them. If they haven't been loaded
already but you want to use them, say for configuring a jail, you're out
of luck.
So add a knob to always load the default rulesets. While I'm here document
the other devfs_ knobs in rc.conf.5.
This should have been included in change 230592.
The supported hardware section still needs some updating to reflect
the current reality.
MFC after: 3 days
TCP_KEEPCNT, that allow to control initial timeout, idle time, idle
re-send interval and idle send count on a per-socket basis.
Reviewed by: andre, bz, lstewart
kernel modules that include binary-only code.
More fine-grained control is provided via MK_SOURCELESS_HOST (for native code
that runs on host CPU) and MK_SOURCELESS_UCODE (for microcode).
Reviewed by: julian, delphij, freebsd-arch
Approved by: kib (mentor)
MFC after: 2 weeks
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
share/man/man4/Makefile,
share/man/man4/xnb.4,
sys/dev/xen/netback/netback.c,
sys/dev/xen/netback/netback_unit_tests.c:
Rewrote the netback driver for xen to attach properly via newbus
and work properly in both HVM and PVM mode (only HVM is tested).
Works with the in-tree FreeBSD netfront driver or the Windows
netfront driver from SuSE. Has not been extensively tested with
a Linux netfront driver. Does not implement LRO, TSO, or
polling. Includes unit tests that may be run through sysctl
after compiling with XNB_DEBUG defined.
sys/dev/xen/blkback/blkback.c,
sys/xen/interface/io/netif.h:
Comment elaboration.
sys/kern/uipc_mbuf.c:
Fix page fault in kernel mode when calling m_print() on a
null mbuf. Since m_print() is only used for debugging, there
are no performance concerns for extra error checking code.
sys/kern/subr_scanf.c:
Add the "hh" and "ll" width specifiers from C99 to scanf().
A few callers were already using "ll" even though scanf()
was handling it as "l".
Submitted by: Alan Somers <alans@spectralogic.com>
Submitted by: John Suykerbuyk <johns@spectralogic.com>
Sponsored by: Spectra Logic
MFC after: 1 week
Reviewed by: ken
text there was so much outdated that it required a complete
rewrite even for inet.4, not mentioning inet6.4. There is
no reason to keep it in the manual page.
selection in snd_hda(4) driver.
Now driver tracks jack presence detection status for every CODEC pin. For
playback associations, when configured, that information, same as before,
can be used to automatically redirect audio to headphones. Also same as
before, these events are used to track digital display connection status
and fetch ELD. Now in addition to that driver uses that information to
automatically switch recording source of the mixer to the connected input.
When there are devices with no jack detection and with one both connected,
last ones will have the precedence. As result, on most laptops after boot
internal microphone should be automatically selected. But if external one
(for example, headset) connected, it will be selected automatically.
When external mic disconnected, internal one will be selected again.
Automatic recording source selection is enabled by default now to make
recording work out of the box without touching mixer. But it can be
disabled or limited only to attach time using hint.pcm.X.rec.autosrc loader
tunables or dev.pcm.X.rec.autosrc sysctls.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
These functions take a `struct cdev *' -- not a dev_t. Inside the
kernel, dev_t has the same use as in userspace, namely to store a device
identifier.
MFC after: 2 weeks
- Huge old hdac driver was split into three independent pieces: HDA
controller driver (hdac), HDA CODEC driver (hdacc) and HDA sudio function
driver (hdaa).
- Support for multichannel recording was added. Now, as specification
defines, driver checks input associations for pins with sequence numbers
14 and 15, and if found (usually) -- works as before, mixing signals
together. If it doesn't, it configures input association as multichannel.
- Signal tracer was improved to look for cases where several DACs/ADCs in
CODEC can work with the same audio signal. If such case found, driver
registers additional playback/record stream (channel) for the pcm device.
- New controller streams reservation mechanism was implemented. That
allows to have more pcm devices then streams supported by the controller
(usually 4 in each direction). Now it limits only number of simultaneously
transferred audio streams, that is rarely reachable and properly reported
if happens.
- Codec pins and GPIO signals configuration was exported via set of
writable sysctls. Another sysctl dev.hdaa.X.reconfig allows to trigger
driver reconfiguration in run-time.
- Driver now decodes pins location and connector type names. In some cases
it allows to hint user where on the system case connectors, related to the
pcm device, are located. Number of channels supported by pcm device,
reported now (if it is not 2), should also make search easier.
- Added workaround for digital mic on some Asus laptops/netbooks.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
Document the current semantics of the 'quiet' command prefix
in the rc.subr(8).
Fix dhclient rc.d script: it should not call err() for
non-DHCP-enabled interface when it is called from devd, because the
latter just blindly calls 'service dhclient quietstart' on each "link
up" event.
Since the 'quietstart' will silence the message "Cannot 'start' <foo>.
Set <foo>_enable to YES in /etc/rc.conf or use 'onestart' instead of
'start'." and running dhclient on the non-DHCP-enabled interface is
the same thing as running the service <foo> without <foo>_enable set,
such modification is in sync with the current semantics of the 'quiet'
prefix.
Approved by: glebius
Reviewed by: freebsd-rc list
MFC after: 2 weeks
CTL is a disk and processor device emulation subsystem originally written
for Copan Systems under Linux starting in 2003. It has been shipping in
Copan (now SGI) products since 2005.
It was ported to FreeBSD in 2008, and thanks to an agreement between SGI
(who acquired Copan's assets in 2010) and Spectra Logic in 2010, CTL is
available under a BSD-style license. The intent behind the agreement was
that Spectra would work to get CTL into the FreeBSD tree.
Some CTL features:
- Disk and processor device emulation.
- Tagged queueing
- SCSI task attribute support (ordered, head of queue, simple tags)
- SCSI implicit command ordering support. (e.g. if a read follows a mode
select, the read will be blocked until the mode select completes.)
- Full task management support (abort, LUN reset, target reset, etc.)
- Support for multiple ports
- Support for multiple simultaneous initiators
- Support for multiple simultaneous backing stores
- Persistent reservation support
- Mode sense/select support
- Error injection support
- High Availability support (1)
- All I/O handled in-kernel, no userland context switch overhead.
(1) HA Support is just an API stub, and needs much more to be fully
functional.
ctl.c: The core of CTL. Command handlers and processing,
character driver, and HA support are here.
ctl.h: Basic function declarations and data structures.
ctl_backend.c,
ctl_backend.h: The basic CTL backend API.
ctl_backend_block.c,
ctl_backend_block.h: The block and file backend. This allows for using
a disk or a file as the backing store for a LUN.
Multiple threads are started to do I/O to the
backing device, primarily because the VFS API
requires that to get any concurrency.
ctl_backend_ramdisk.c: A "fake" ramdisk backend. It only allocates a
small amount of memory to act as a source and sink
for reads and writes from an initiator. Therefore
it cannot be used for any real data, but it can be
used to test for throughput. It can also be used
to test initiators' support for extremely large LUNs.
ctl_cmd_table.c: This is a table with all 256 possible SCSI opcodes,
and command handler functions defined for supported
opcodes.
ctl_debug.h: Debugging support.
ctl_error.c,
ctl_error.h: CTL-specific wrappers around the CAM sense building
functions.
ctl_frontend.c,
ctl_frontend.h: These files define the basic CTL frontend port API.
ctl_frontend_cam_sim.c: This is a CTL frontend port that is also a CAM SIM.
This frontend allows for using CTL without any
target-capable hardware. So any LUNs you create in
CTL are visible in CAM via this port.
ctl_frontend_internal.c,
ctl_frontend_internal.h:
This is a frontend port written for Copan to do
some system-specific tasks that required sending
commands into CTL from inside the kernel. This
isn't entirely relevant to FreeBSD in general,
but can perhaps be repurposed.
ctl_ha.h: This is a stubbed-out High Availability API. Much
more is needed for full HA support. See the
comments in the header and the description of what
is needed in the README.ctl.txt file for more
details.
ctl_io.h: This defines most of the core CTL I/O structures.
union ctl_io is conceptually very similar to CAM's
union ccb.
ctl_ioctl.h: This defines all ioctls available through the CTL
character device, and the data structures needed
for those ioctls.
ctl_mem_pool.c,
ctl_mem_pool.h: Generic memory pool implementation used by the
internal frontend.
ctl_private.h: Private data structres (e.g. CTL softc) and
function prototypes. This also includes the SCSI
vendor and product names used by CTL.
ctl_scsi_all.c,
ctl_scsi_all.h: CTL wrappers around CAM sense printing functions.
ctl_ser_table.c: Command serialization table. This defines what
happens when one type of command is followed by
another type of command.
ctl_util.c,
ctl_util.h: CTL utility functions, primarily designed to be
used from userland. See ctladm for the primary
consumer of these functions. These include CDB
building functions.
scsi_ctl.c: CAM target peripheral driver and CTL frontend port.
This is the path into CTL for commands from
target-capable hardware/SIMs.
README.ctl.txt: CTL code features, roadmap, to-do list.
usr.sbin/Makefile: Add ctladm.
ctladm/Makefile,
ctladm/ctladm.8,
ctladm/ctladm.c,
ctladm/ctladm.h,
ctladm/util.c: ctladm(8) is the CTL management utility.
It fills a role similar to camcontrol(8).
It allow configuring LUNs, issuing commands,
injecting errors and various other control
functions.
usr.bin/Makefile: Add ctlstat.
ctlstat/Makefile
ctlstat/ctlstat.8,
ctlstat/ctlstat.c: ctlstat(8) fills a role similar to iostat(8).
It reports I/O statistics for CTL.
sys/conf/files: Add CTL files.
sys/conf/NOTES: Add device ctl.
sys/cam/scsi_all.h: To conform to more recent specs, the inquiry CDB
length field is now 2 bytes long.
Add several mode page definitions for CTL.
sys/cam/scsi_all.c: Handle the new 2 byte inquiry length.
sys/dev/ciss/ciss.c,
sys/dev/ata/atapi-cam.c,
sys/cam/scsi/scsi_targ_bh.c,
scsi_target/scsi_cmds.c,
mlxcontrol/interface.c: Update for 2 byte inquiry length field.
scsi_da.h: Add versions of the format and rigid disk pages
that are in a more reasonable format for CTL.
amd64/conf/GENERIC,
i386/conf/GENERIC,
ia64/conf/GENERIC,
sparc64/conf/GENERIC: Add device ctl.
i386/conf/PAE: The CTL frontend SIM at least does not compile
cleanly on PAE.
Sponsored by: Copan Systems, SGI and Spectra Logic
MFC after: 1 month
This switches us to using -isoC-2011 as the symbol name which is used by
groff and mdocml. It follows the change to 4 digit years as done with
IEEE Std 1003 post-1999.
MFC after: 2 weeks (groff changes only)
The macro construction used now, is almost identical to the code
provided in C11 proposal N1404. This new version doesn't seem to
introduce any regressions according to the regression test in tools/,
but still seems to malfunction with Clang on certain aspects.
The new code does work successfully with GCC 4.2, 4.6 and 4.7. With 4.7,
it also works when __generic() is implemented on top of _Generic().
Discussed with: stefanf
I was considering adding it to libc as well, but last minute I thought
it would be good enough to add it to libkern exclusively. I forgot to
rename the man page and hook it up.
It seems two of the file system drivers we have in the tree, namely ufs
and ext3, use a function called `skpc()'. The meaning of this function
does not seem to be documented in FreeBSD, but it turns out one needs to
be a VAX programmer to understand what it does.
SPKC is an instruction on the VAX that does the opposite of memchr(). It
searches for the non-equal character. Add a new function called
memcchr() to the tree that has the following advantages over skpc():
- It has a name that makes more sense than skpc(). Just like strcspn()
matches the complement of strspn(), memcchr() is the complement of
memchr().
- It is faster than skpc(). Similar to our strlen() in libc, it compares
entire words, instead of single bytes. It seems that for this routine
this yields a sixfold performance increase on amd64.
- It has a man page.
aspect of time stamp configuration per interface rather than per BPF
descriptor. Prior to this, the order in which BPF devices were opened and the
per descriptor time stamp configuration settings could cause non-deterministic
and unintended behaviour with respect to time stamping. With the new scheme, a
BPF attached interface's tscfg sysctl entry can be set to "default", "none",
"fast", "normal" or "external". Setting "default" means use the system default
option (set with the net.bpf.tscfg.default sysctl), "none" means do not
generate time stamps for tapped packets, "fast" means generate time stamps for
tapped packets using a hz granularity system clock read, "normal" means
generate time stamps for tapped packets using a full timecounter granularity
system clock read and "external" (currently unimplemented) means use the time
stamp provided with the packet from an underlying source.
- Utilise the recently introduced sysclock_getsnapshot() and
sysclock_snap2bintime() KPIs to ensure the system clock is only read once per
packet, regardless of the number of BPF descriptors and time stamp formats
requested. Use the per BPF attached interface time stamp configuration to
control if sysclock_getsnapshot() is called and whether the system clock read
is fast or normal. The per BPF descriptor time stamp configuration is then
used to control how the system clock snapshot is converted to a bintime by
sysclock_snap2bintime().
- Remove all FAST related BPF descriptor flag variants. Performing a "fast"
read of the system clock is now controlled per BPF attached interface using
the net.bpf.tscfg sysctl tree.
- Update the bpf.4 man page.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
In collaboration with: Julien Ridoux (jridoux at unimelb edu au)
7.x, 8.x and 9.x with pf(4) imports: pfsync(4) should suppress CARP
preemption, while it is running its bulk update.
However, reimplement the feature in more elegant manner, that is
partially inspired by newer OpenBSD:
- Rename term "suppression" to "demotion", to match with OpenBSD.
- Keep a global demotion factor, that can be raised by several
conditions, for now these are:
- interface goes down
- carp(4) has problems with ip_output() or ip6_output()
- pfsync performs bulk update
- Unlike in OpenBSD the demotion factor isn't a counter, but
is actual value added to advskew. The adjustment values for
particular error conditions are also configurable, and their
defaults are maximum advskew value, so a single failure bumps
demotion to maximum. This is for POLA compatibility, and should
satisfy most users.
- Demotion factor is a writable sysctl, so user can do
foot shooting, if he desires to.
to selectively work around warnings in programs that don't use flexible
array members, but instead define arrays of length 1 at the end of the
struct, and then access those beyond their declared bounds.
MFC after: 1 week
from scratch, copying needed functionality from the old implemenation
on demand, with a thorough review of all code. The main change is that
interface layer has been removed from the CARP. Now redundant addresses
are configured exactly on the interfaces, they run on.
The CARP configuration itself is, as before, configured and read via
SIOCSVH/SIOCGVH ioctls. A new prefix created with SIOCAIFADDR or
SIOCAIFADDR_IN6 may now be configured to a particular virtual host id,
which makes the prefix redundant.
ifconfig(8) semantics has been changed too: now one doesn't need
to clone carpXX interface, he/she should directly configure a vhid
on a Ethernet interface.
To supply vhid data from the kernel to an application the getifaddrs(8)
function had been changed to pass ifam_data with each address. [1]
The new implementation definitely closes all PRs related to carp(4)
being an interface, and may close several others. It also allows
to run a single redundant IP per interface.
Big thanks to Bjoern Zeeb for his help with inet6 part of patch, for
idea on using ifam_data and for several rounds of reviewing!
PR: kern/117000, kern/126945, kern/126714, kern/120130, kern/117448
Reviewed by: bz
Submitted by: bz [1]
- Device configuration via plain text config file. Also able to operate
when not attached to the chip as the master driver.
- Generic "work request" queue that serves as the base for both ctrl and
ofld tx queues.
- Generic interrupt handler routine that can process any event on any
kind of ingress queue (via a dispatch table).
- A couple of new driver ioctls. cxgbetool can now install a firmware
to the card ("loadfw" command) and can read the card's memory
("memdump" and "tcb" commands).
- Lots of assorted information within dev.t4nex.X.misc.* This is
primarily for debugging and won't show up in sysctl -a.
- Code to manage the L2 tables on the chip.
- Updates to cxgbe(4) man page to go with the tunables that have changed.
- Updates to the shared code in common/
- Updates to the driver-firmware interface (now at fw 1.4.16.0)
MFC after: 1 month
objects created by shm_open(2) into the kernel's address space. This
provides a convenient way for creating shared memory buffers between
userland and the kernel without requiring custom character devices.
against text. Provide the override switch to turn off the strict
behaviour. Apparently, openssl libcrypto needs it due to assembler
code not being PIC.
Discussed with: bf
MFC after: 2 weeks
to known AHCI-capable chips (AMD/NVIDIA), configured for legacy emulation.
Enabled by default to get additional performance and functionality of AHCI
when it can't be enabled by BIOS. Can be disabled to honor BIOS settings if
needed for some reason.
MFC after: 1 month
to enable and configure the functionality.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
Discussed with: Julien Ridoux (jridoux at unimelb edu au)
Submitted by: Julien Ridoux (jridoux at unimelb edu au)
defined based on WITH/WITHOUT_CTF settings, default is WITHOUT_CTF,
NO_CTF overrides WITH_CTF (used by Makefile.inc1)
- CTFCONVERT_CMD/NORMAL_CTFCONVERT are now defined to empty string
if make(1) can handle empty commands
- CTFCONVERT_CMD=... is a hack (should be defined to empty string instead):
make(1) should be taught to ignore empty commands silently in compat mode
(as it does in !compat mode, GNU make also silently ignores empty commands)
and to skip printing empty commands in !compat mode
- config(8) should generate ${NORMAL_CTFCONVERT} invocation without '@':
this will allow to simplify kern.pre.mk even more and lessen the number
of shell invocations during kernel build when CTF is turned off
- WITH_CTF can now be converted to usual MK_CTF=yes/no infrastructure
Pointy hat to: fjoe [1]
This is required to override knobs (e.g. WITH_PROFILE) during buildworld
stages in Makefile.inc1 (otherwise the build is stopped due to both WITH_FOO
and WITHOUT_FOO defined).
its mechanisms, pointing at other pertinent man pages, and cautioning about
the experimental status of Capsicum in FreeBSD.
MFC after: 3 days
Sponsored by: Google, Inc.
not disabled in the usual way (by adding it to __DEFAULT_NO_OPTIONS in
share/mk/bsd.own.mk), and because the test for MK_LIBCPLUSPLUS in
Makefile.inc1 was incorrect.
Pointy hat to: dim
MK_LIBCPLUSPLUS=yes to enable). This is a work-in-progress. It works for
me, but is not guaranteed to work for anyone else and may eat your dog.
To build C++ using libc++, add -stdlib=libc++ to your CXX and LD flags.
Bug reports welcome, bug fixes even more welcome...
Approved by: dim (mentor)
and DEVMETHOD() we can fully hide the explicit mention of kobj(9) from
device drivers.
- Update the example in driver.9 to use DEVMETHOD_END.
Submitted by: jhb
MFC after: 3 days
