The caph_enter function should made it easier to sandbox application
and not force us to remember that we need to check errno on failure.
Another function is also checking if casper is present.
Reviewed by: emaste, cem (partially)
Differential Revision: https://reviews.freebsd.org/D14557
The canonical check for whether or not a ring is drainable is
TXQ_AVAIL() > MAX_TX_DESC() + 2. Use this same construct here,
in order to avoid a potential off-by-one error where we might otherwise
fail to request an interrupt.
Reviewed by: mmacy
Sponsored by: Netflix
Boost the priority of user-space threads when they set
their affinity to a core to adjust its frequency. This avoids a situation
where a CPU bound kernel thread with the same affinity is running on a
down-clocked core, and will "block" powerd from up-clocking the core
until the kernel thread yields. This can lead to poor perfomance,
and to things potentially getting stuck on Giant.
Reviewed by: kib (imp reviewed earlier version)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D15246
memmove is repurposed bcopy (arguments swapped, return value added)
The libkern variant is a wrapper around bcopy, so this is a big
improvement.
memset is repurposed memcpy. The librkern variant is doing fishy stuff,
including branching on 0 and calling bzero.
Both functions are rather crude and subject to partial depessimization.
This is a soft prerequisite to adding variants utilizing the
'Enhanced REP MOVSB/STOSB' bit and let the kernel patch at runtime.
Currently when net.inet.carp.allow=0 CARP state remains as MASTER, which is
not very useful (if there are other masters -- it can lead to split brain,
if there are none -- it makes no sense). Having it as INIT makes it clear
that carp packets are disabled.
Submitted by: wg
MFC after: 1 month
Relnotes: yes
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D14477
Without a subsequent wbinvd the changes to suspended_cpus (and
resuming_cpus) can be lost at least on AMD systems that use MOESI cache
coherency protocol. That can happen because one of APs ends up as an
Owner of the corresponding cache line(s) and the changes may never reach
the main memory before the AP is reset.
While here, move clearing of suspended_cpus a little bit earlier as the
fact of returning from savectx (with zero return value) means that the
CPU has fully restored it execution context.
Also, rework the comment that describes the need for resuming_cpus.
This change fixed suspend to RAM a previously broken AMD-based system.
Reviewed by: kib
Discussed with: bde
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D15295
The properties 'assigned-clocks', 'assigned-clock-parents' and
'assigned-clock-rates' all work together.
'assigned-clocks' holds the list of clock for which we need to either
assign a new parent or a new frequency.
The old code just supported assigning a new parents, add support for
assigning a new frequency too.
Add support for setting pll rate. On RockChip SoC two kind of plls are
supported, integer mode and fractional mode.
The two modes are intended to support more frequencies for the core plls.
While here change the recalc method as it appears that the datasheet is
wrong on the calculation method.
Add the clock definition for the arm clock.
While here remove the indexes in the clock table as we will need clock
with a 0 index (non-exported clocks).
Most filesystems, with the notable exceptions of msdosfs and autofs use
only vfs_timestamp() to read the current time. This has the benefit of
configurable granularity (using the vfs.timestamp_precision sysctl).
For convenience, use it on msdosfs too.
Submitted by: Damjan Jovanovic
Differential Revision: https://reviews.freebsd.org/D15297
to sleep on commands to the NIC when updating multicast filters. More generally this permitted
driver's to use an sx as a softc lock. Unfortunately this change introduced a race whereby a
a multicast update would still be queued for deletion when ifconfig deleted the interface
thus calling down in to _purgemaddrs and synchronously deleting _all_ of the multicast addresses
on the interface.
Synchronously remove all external references to a multicast address before enqueueing for delete.
Reported by: lwhsu
Approved by: sbruno
https://github.com/illumos/illumos-gate/edit/master/usr/src/lib/libzfs/common/libzfs_sendrecv.c
Patch our version of it to quiesce warnings until someone decides to sync
up our code:
libzfs_sendrecv.c:2555:30: warning: format specifies type 'unsigned long'
but the argument has type 'uint64_t' (aka 'unsigned long long') [-Wformat]
sprintf(guidname, "%lu", thisguid);
~~~ ^~~~~~~~
%llu
libzfs_sendrecv.c:2612:29: warning: format specifies type 'unsigned long'
but the argument has type 'uint64_t' (aka 'unsigned long long') [-Wformat]
sprintf(guidname, "%lu", parent_fromsnap_guid);
~~~ ^~~~~~~~~~~~~~~~~~~~
%llu
libzfs_sendrecv.c:2645:29: warning: format specifies type 'unsigned long'
but the argument has type 'uint64_t' (aka 'unsigned long long') [-Wformat]
sprintf(guidname, "%lu", parent_fromsnap_guid);
~~~ ^~~~~~~~~~~~~~~~~~~~
%llu
Reviewed by: allanjude
Differential Revision: https://reviews.freebsd.org/D15325
With Linux 4.17 dts the compatible for the prcm added 'simplebus' we mean
that the simplebus driver will attach to it at the BUS_PASS_BUS pass.
Change the pass for the prcm driver to be at BUS_PASS_BUS so we will win
the attach.
This introduce a problem as this driver needs the ti_scm one to be already
attached. ti_scm also attach at BUS_PASS_BUS but after the prcm one as it is
after in the dtb and the simplebus driver simpy walk the tree to attach it's
children.
Use the bus_new_pass method to defer the frequencies read at BUS_PASS_TIMER.
This fixes booting on BeagleBone*
Reported by: many
em(4) and igb(4) were tested by me, and ixgbe(4) and bnxt(4) were
tested by sbruno.
Reviewed by: mmacy, shurd
MFC after: 1 month
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D15262
A new usage is added so that parameters for netdump may be specified.
Specifically, one configures an interface for netdump with:
# dumpon -c <client IP> -s <server IP> [-g <gateway IP>] <iface name>
Reviewed by: bdrewery, cem (earlier versions), sbruno
MFC after: 1 month
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D15254
This is a component of a system which lets the kernel dump core to
a remote host after a panic, rather than to a local storage device.
The server component is available in the ports tree. netdump is
particularly useful on diskless systems.
The netdump(4) man page contains some details describing the protocol.
Support for configuring netdump will be added to dumpon(8) in a future
commit. To use netdump, the kernel must have been compiled with the
NETDUMP option.
The initial revision of netdump was written by Darrell Anderson and
was integrated into Sandvine's OS, from which this version was derived.
Reviewed by: bdrewery, cem (earlier versions), julian, sbruno
MFC after: 1 month
X-MFC note: use a spare field in struct ifnet
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D15253
The aim is to permit mbuf allocations after a panic without calling into
the page allocator, without imposing any runtime overhead during regular
operation of the system, and without modifying driver code. The approach
taken is to preallocate a number of mbufs and clusters, storing them
in linked lists, and using the lists to back some UMA cache zones. At
panic time, the mbuf and cluster zone pointers are overwritten with
those of the cache zones so that the mbuf allocator returns
preallocated items.
Using this scheme, drivers which cache mbuf zone pointers from
m_getzone() require special handling when implementing netdump support.
Reviewed by: cem (earlier version), julian, sbruno
MFC after: 1 month
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D15251
Doing so introduces races which can lead to a use-after-free when
grabbing a snapshot of the GEOM mesh.
To ensure that a mirror's disk list remains stable, change its locking
protocol: both the softc lock and the topology lock are now required
to modify the list, so either lock is sufficient for traversal.
Tested by: pho
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
to avoid a LOR on the multicast list lock in the freemoptions routines.
As it turns out, tcp_usr_detach can acquire the tcbinfo lock readonly.
Trying to wunlock the pcbinfo lock in that context has caused a number
of reported crashes.
This change unclutters in_pcbfree and moves the handling of wunlock vs
runlock of pcbinfo to the freemoptions routine.
Reported by: mjg@, bde@, o.hartmann at walstatt.org
Approved by: sbruno
These firmwares and the following list of changes are from the public
ChelsioUwire-3.7.1.0 release.
T6 Firmware
================================================================================
Version : 1.19.1.0
Date : 04/23/2018
================================================================================
Fixes
-----
BASE:
- Fixed traffic stall when rate-limit is modified while running traffic.
- Fixes a firmware crash in FW_ETH_TX_EO_WR handling.
- Fixes host DCB support when FW_PORT_CMD is used.
ETH:
- Exit Auto-Negotiation if we don't receive base page from peer within 10s.
This fixes some cases where in we keep on restarting auto negotiation without
ever exiting, resulting in link failure.
- Fixes an issue where VF packets counter were not increasing if VF packets
coalesced WR is used by driver.
OFLD:
- Kernel and user mode NVMEoF performance enhancements.
FOiSCSI:
- Fixes fw crash when trying to connect to non-existence IPv6 iSNS target.
================================================================================
Version : 1.18.9.0
Date : 03/27/2018
================================================================================
Fixes
-----
BASE:
- For Ethernet frames less than 64B, pad them with zero bytes as per IEEE spec
(RFC 894).
- Added a new parameter iqtype to FW_IQ_CMD to identify the ingress NIC or offload
queues. This fixes an issue where driver was receiving interrupt with no new
messages in queue.
- FW_PARAMS_CMD processes all the valaid paramaters and returns value 0UL for
any unknown parameter.
OFLD:
- Fixes connection failure during SRQ reuse.
- Fixes incorrect cqe in case of WRITE with immediate operation.
FOiSCSI:
- Fixes a fw crash when wrong node-id is passed to FW_FOISCSI_CTRL_WR.
FOFCoE:
- Fixes a fw hang while creating NPIV.
Enhancements
------------
ETH:
- A new WR FW_ETH_TX_PKTS_VM_WR added to support VM packet coalescing.
================================================================================
Version : 1.18.4.0
Date : 02/28/2018
================================================================================
Fixes
-----
BASE:
- Fixed Rate limiting not working for 101Mbps<=rate limit<=163Mbps range.
- Fixed starting more than 32 VMs on PF4 causing firmware hang.
ETH:
- Fixed link failure due to FEC mismatch with optics.
- Fixed link failure with link toggle stress tests.
- Only BaseR FEC is supported for 50G.
- Fixed a bug in next page handling which sometimes causes link down.
- Fixed port down due to failre to read eeprom contents of some modules.
- Fixed a bug causing adapter to fail with spider configuration.
FOiSCSI:
- Fixed a bug causing login failure when connecting to multiple targets.
Enhancements
------------
BASE:
- Added a new firmware API to retrieve the maximum temperaturethreshold for
the chip (FW_PARAM_DEV_DIAG_MAXTMPTHRESH).
ETH:
- Added support for user to contol pause negotiation during auto negotiation.
FOiSCSI:
- Added a new facility to redirect few fw events to offload rx queue
(based on driver's configration)
- Driver can ignore providing ipv6 prefix len during ipv6 address configuration.
================================================================================
Version : 1.17.14.0
Date : 12/27/2017
================================================================================
FIXES
-----
BASE:
- Fixed an FLR failure during simulteneous power up of VM.
- Fixed an issue in vlan acl which was limiting vlan range to 1024.
ETH:
- Enabled RS-FEC for 25G active copper cable and 25GBASE-SR.
- When auto negotiation is enabled, final pause settings are resolved
based on local and peer pause settings.
- Handle NACK for an I2C access.
OFLD
- Fixed rdma connection cleanup in SO adpater.
- Fixed rdma connections during read invalidate.
- Fixed the crash when invalid BW rate is passed to fw.
- Fixed the traffic hang when BW allocation is changed from switch during traffic.
FOFCoE:
- Fixed an issue where initiator remains logged-in even after LLDP is disabled
on switch.
ENHANCEMENTS
------------
BASE:
- Added support for 248 VFs.
- Added fw driver periodic calibration for MC.
ETH:
- Added XLAUI port type support.
- Added raw mac entry deletion support (FW_VI_MAC_ID_BASED_FREE).
OFLD:
- Inline IPSec support added (flag F_FW_ULPTX_WR_DATA indicates the inline
IPSec WR).
- New work request FW_RI_RDMA_WRITE_CMPL_WR (write with completion) added to
T5 Firmware
================================================================================
Version : 1.19.1.0
Date : 04/23/2018
================================================================================
Fixes
-----
BASE:
- Fixes a firmware crash in FW_ETH_TX_EO_WR handling.
- Fixes host DCB support when FW_PORT_CMD is used.
ETH:
- Fixes an issue where VF packets counter were not increasing if VF packets
coalesced WR is used by driver.
OFLD:
- Fixes an issue where fw hangs if max traffic rate passed is 0.
FOiSCSI:
- Fixes fw crash when trying to connect to non-existence IPv6 iSNS target.
================================================================================
Version : 1.18.9.0
Date : 03/27/2018
================================================================================
Fixes
-----
BASE:
- For Ethernet frames less than 64B, pad them with zero bytes as per IEEE spec
(RFC 894).
- Added a new parameter iqtype to FW_IQ_CMD to identify the ingress NIC or offload
queues. This fixes an issue where driver was receiving interrupt with no new
messages in queue.
ETH:
- Pad the Ethernet packets of size less than 64B with zeros. This fixes the
incorrect checksum generation of packets less then 64B.
FOiSCSI:
- Fixes a fw crash when wrong node-id is passed to FW_FOISCSI_CTRL_WR.
FOFCoE:
- Fixes a fw hang while creating NPIV.
Enhancements
------------
ETH:
- A new WR FW_ETH_TX_PKTS_VM_WR added to support VM packet coalescing.
================================================================================
Version : 1.18.4.0
Date : 02/28/2018
================================================================================
Fixes
-----
BASE:
- Fixed starting more than 32 VMs on PF4 causing firmware hang.
FOiSCSI:
- Fixed a bug causing login failure when connecting to multiple targets.
Enhancements
------------
BASE:
- Added a new firmware API to retrieve the maximum temperaturethreshold for
the chip (FW_PARAM_DEV_DIAG_MAXTMPTHRESH).
ETH:
- Added support for user to contol pause negotiation during auto negotiation.
FOiSCSI:
- Added a new facility to redirect few fw events to offload rx queue
(based on driver's configration)
- Driver can ignore providing ipv6 prefix len during ipv6 address configuration.
================================================================================
Version : 1.17.14.0
Date : 12/27/2017
================================================================================
FIXES
-----
BASE:
- Fixed an issue in vlan acl which was limiting vlan range to 1024.
ETH:
- Corrected lane inversion logic.
- Fixed improper LED behavior in T580 cards.
- When auto negotiation is enabled, final pause settings are resolved
based on local and peer pause settings.
- Handle NACK for an I2C access.
OFLD
- Fixed rdma connections during read invalidate.
FOiSCSI:
- Fixed a connections hang when link is toggled frequently.
FOFCoE:
- Fixed an issue where initiator remains logged-in even after LLDP is disabled
on switch.
ENHANCEMENTS
------------
BASE:
- Added support for 124 VFs.
ETH:
- Added XLAUI port type support.
- Added raw mac entry deletion support (FW_VI_MAC_ID_BASED_FREE).
OFLD:
- New work request FW_RI_RDMA_WRITE_CMPL_WR (write with completion) added to
optimize NVMEoF write.
T4 Firmware
================================================================================
Version : 1.19.1.0
Date : 04/23/2018
================================================================================
Fixes
-----
BASE:
- Fixes a firmware crash in FW_ETH_TX_EO_WR handling.
- Fixes host DCB support when FW_PORT_CMD is used.
FOiSCSI:
- Fixes fw crash when trying to connect to non-existence IPv6 iSNS target.
================================================================================
Version : 1.18.9.0
Date : 03/27/2018
================================================================================
Fixes
-----
BASE:
- Added a new paramter iqtype to FW_IQ_CMD to identify the ingress NIC or
offload queues. This fixes an issue where driver was receiving interrupt with
no new messages in queue.
FOFCoE:
- Fixes a fw hang while creating NPIV.
Enhancements
------------
ETH:
- A new WR FW_ETH_TX_PKTS_VM_WR added to support VM packet coalescing.
================================================================================
Version : 1.18.4.0
Date : 02/28/2018
================================================================================
Enhancements
------------
BASE:
- Added a new firmware API to retrieve the maximum temperaturethreshold for
the chip (FW_PARAM_DEV_DIAG_MAXTMPTHRESH).
================================================================================
Version : 1.17.14.0
Date : 12/27/2017
================================================================================
FIXES
-----
BASE:
- Fixed an issue in vlan acl which was limiting vlan range to 1024.
MFC after: 3 days
Sponsored by: Chelsio Communications
This allows create/delete/attach/detach namespaces on new NVMe controllers.
This is only a first user-level part of the bigger change set. Kernel part
required to detect and handle the configuration changes without reboot is
completely independent and will be added separately.
Submitted by: Matt Williams <mffbsdw@gmail.com> (original version)
Differential Revision: https://reviews.freebsd.org/D11399
warning:
make[3]: "/usr/src/share/mk/bsd.prog.mk" line 274: warning: duplicate
script for target "_scriptsinstall" ignored
make[3]: "/usr/src/share/mk/bsd.prog.mk" line 274: warning: using
previous script for "_scriptsinstall" defined here
Reviewed by: kevans
The POWER9 MMU (PowerISA 3.0) is slightly different from current
configurations, using a partition table even for hypervisor mode, and
dropping the SDR1 register. Key off the newly early-enabled CPU features
flags for the new architecture, and configure the MMU appropriately.
The POWER9 MMU ignores the "PSIZ" field in the PTCR, and expects a 64kB
table. As we are enabled for powernv (hypervisor mode, no VMs), only
initialize partition table entry 0, and zero out the rest. The actual
contents of the register are identical to SDR1 from previous architectures.
Along with this, fix a bug in the page table allocation with very large
memory. The table can be allocated on any 256k boundary. The
bootstrap_alloc alignment argument is an int, and with large amounts of
memory passing the size of the table as the alignment will overflow an
integer. Hard-code the alignment at 256k as wider alignment is not
necessary.
Reviewed by: nwhitehorn
Tested by: Breno Leitao
Relnotes: Yes
The new POWER9 MMU configuration is slightly different from current setups.
Rather than special-casing on POWER9, move the initialization of cpu_features
and cpu_features2 to as early as possible, so that platform and MMU
configuration can be based upon CPU features instead of specific CPUs if at all
possible.
Reviewed by: nwhitehorn
POWER8 and POWER9 have similar configuration requirements for hypervisor setup,
and in the cases here they're identical. Add the POWER9 constant to the POWER8
list so it's initialized correctly.
Reviewed by: nwhitehorn
Originally, I overlooked that PMIO register 0xc0 has a dual personality.
It can either be S5/Reset Status register or Misc. Fix register (aka
debug status register). The mode is controlled by bit 2 in PMIO
register 0xc4. Apparently there are register programming requirements
for the second personality, so many BIOSes leave the register, after
programming it, in that mode. So, we need to switch the register to the
correct mode.
Additionally, AMDSB8_WD_RST_STS was defined incorrectly as bit 13 while
it is actually bit 25 (and the register's width is 32 bits, not 16).
With this change I see the following in dmesg after a reset by the
watchdog:
amdsbwd0: ResetStatus = 0x42000000
amdsbwd0: Previous Reset was caused by Watchdog
MFC after: 2 weeks
For most buses all children are equal, so the order does not matter.
Other buses, such as acpi, carefully order their child devices to
express implicit dependencies between them. For such buses it is safer
to bring down devices in the reverse order.
I believe that this is the reason why hpet_suspend had to be disabled.
Some drivers depend on a working event timer until they are suspended.
But previously we would suspend hpet very early.
I tested this change by makinbg hpet_suspend actually stop HPET timers
and tested that too.
Note that this change is not a complete solution as it does not take
into account bus passes.
A better approach would be to track the actual attach order of the
devices and to use the reverse of that.
Reviewed by: imp, mav
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D15291
