aac driver dependent on the linux emulation module. This was
especially bad for the release engineers who tried to move the
aac driver from the kernel onto the drivers floppy. The linux
compat bits for this driver are now in their own driver, aac_linux.
It can be loaded as a module or compiled into the kernel. For
the latter case, the AAC_COMPAT_LINUX option is needed, along with
the COMPAT_LINUX option.
I've tested this in every configuration I can think of. This is an
MFC candidate for 4.7.
Idea from: rwatson
MFC after: 3 days
ACPI or for when ACPI support is disabled or not present in the kernel.
Basically, the nexus device is now split into two with some parts
(such as adding default ISA, MCA, and EISA busses if they aren't found
as well as support for PCI bus device ivars) being moved to the legacy
driver.
so that it is MI. Allow nfs_mountroot to return an error if the nfs_diskless
struct is not valid, rather than panicing later on. Call nfs_setup_diskless()
from nfs_mountroot if NFS_ROOT is defined, like bootpc_init(). Removed legacy
root mount support for sparc64, and enabled NFS_ROOT by default.
under way to move the remnants of the a.out toolchain to ports. As the
comment in src/Makefile said, this stuff is deprecated and one should not
expect this to remain beyond 4.0-REL. It has already lasted WAY beyond
that.
Notable exceptions:
gcc - I have not touched the a.out generation stuff there.
ldd/ldconfig - still have some code to interface with a.out rtld.
old as/ld/etc - I have not removed these yet, pending their move to ports.
some includes - necessary for ldd/ldconfig for now.
Tested on: i386 (extensively), alpha
support this, we do have MI code that references it and is otherwise
unaware of an override. The alternative is to put knowledge in these
MI files about which platforms have the opt_kstack_pages.h option file.
It is more likely that other platforms will gain the ability to tune the
kstack size.
if compiling with I686_CPU as a target. CPU_DISABLE_SSE will prevent
this from happening and will guarantee the code is not compiled in.
I am still not happy with this, but gcc is now generating code that uses
these instructions if you set CPUTYPE to p3/p4 or athlon-4/mp/xp or higher.
ev6 or pca56 etc this downgrades the cpu specification passed to gas.
As a result, gas will fail when gcc generates media instructions (in
uipc_usrreq.c). This only affects what gas will accept, not what gcc
generates or what our *.s file contain.
i4bq931, i4b, isic, iwic, ifpi, ifpi2, ifpnp, ihfc, and itjc are
no longer count devices. Also remove a few other instances of N<DEVICE>
being used to control compilation of whole files.
Reviewed by: hm
This feature can be disabled via the AHD/AHC_REG_PRETTY_PRINT kernel
option.
The ahc driver now uses the same debug options mechanism as ahd:
AHC_DEBUG - Compile in debugging code
AHC_DEBUG_OPTS - String of debug options as listed in aic7xxx.h
kld's anywhere, and it was always possible to load ELF kld's even in an
a.out kernel. There is no reason for this to exist anymore, and a.out
kld support has been suffering serious bitrot over the years. They have
not been fully functional for quite some time.
the environment for the last command of the pipeline (xargs) instead
of too early in the broken version or using an extra env process for
each command spawned by xargs as in rev.1.12. Fixed a nearby English
error.
can avoid the cost of a large number of atomic operations if we're not
interested in the object count statistics.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
This is an architecture that present a thing message passing interface
to the OS. You can query as to how many ports and what kind are attached
and enable them and so on.
A less grand view is that this is just another way to package SCSI (SPI or
FC) and FC-IP into a one-driver interface set.
This driver support the following hardware:
LSI FC909: Single channel, 1Gbps, Fibre Channel (FC-SCSI only)
LSI FC929: Dual Channel, 1-2Gbps, Fibre Channel (FC-SCSI only)
LSI 53c1020: Single Channel, Ultra4 (320M) (Untested)
LSI 53c1030: Dual Channel, Ultra4 (320M)
Currently it's in fair shape, but expect a lot of changes over the
next few weeks as it stabilizes.
Credits:
The driver is mostly from some folks from Jeff Roberson's company- I've
been slowly migrating it to broader support that I it came to me as.
The hardware used in developing support came from:
FC909: LSI-Logic, Advansys (now Connetix)
FC929: LSI-Logic
53c1030: Antares Microsystems (they make a very fine board!)
MFC after: 3 weeks
The CAM<>ATAPI layer was submitted by "Thomas Quinot <thomas@cuivre.fr.eu.org>"
changes form the version on the net by me (formatting, ability to be used
alone without the ATAPI native device driver, proper speed reporting...)
See /sys/conf/NOTES for usage.
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
to parse the binary .kld file as a list of symbols. Fix this by
simply deleting the unwanted argument from the ARGV[] array instead
of trying to skip over it.
cards. Since the firmware is hard coded into the kernel, I've made it
a kernel option (WI_SYMBOL_FIRMWARE).
Note: This only downloads into the RAM of these cards. It doesn't
download into FLASH, and is somewhat limited. There needs to be a
better way to deal, but this works for now. My Symbol LA4132 CF card
works now.
Obtained from: NetBSD
kernel access control.
Modify procfs so that (when mounted multilabel) it exports process MAC
labels as the vnode labels of procfs vnodes associated with processes.
Approved by: des
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
controller. Some testing has already been done, but its still greenish.
RAID's has to be setup via the BIOS on the SuperTrak, but all RAID
types are supported by the driver. The SuperTrak rebuilds failed arrays
on the fly and supports spare disks etc etc...
Add "device pst" to your config file to use.
As usual bugsreports, suggestions etc are welcome...
Development sponsored by: Advanis
Hardware donated by: Promise Inc.
MAC support will be merged into the main tree over the next week in
reasonable size chunks; much more to follow.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
pci support. This really needs to be fixed properly some day, but judging
by the fact that the nopci case hasn't compiled for quite a while, there
does not seem to be much urgency.
Reviewed by: sos
This driver actually works slightly better on -stable than on -current
(the system locks on detach on -current), so it should be MFC'd somewhat
sooner.
This driver currently points out a difficulty in the sound device framework.
The PCM unregister routine is allowed to refuse the detach if the device is
in use. In the case of a USB device, however, this unregistration is much more
mandatory in nature, since the device is *actually* gone when this call is
made. The sound subsystem really should not refuse an unregistration and
should take its own steps to reject further I/O. As a result, if you detach
a USB sound device while it is in use, you can expect a panic shortly
thereafter.
This device cannot currently record audio. Some routines are unwritten as
of yet in uaudio.c to support recording.
This device hangs my -current box on detach. I don't know why. This does
not happen on my -stable machine.
Obtained from: Hiroyuki Aizu
MFC after: 2 weeks
handler in the kernel at the same time. Also, allow for the
exec_new_vmspace() code to build a different sized vmspace depending on
the executable environment. This is a big help for execing i386 binaries
on ia64. The ELF exec code grows the ability to map partial pages when
there is a page size difference, eg: emulating 4K pages on 8K or 16K
hardware pages.
Flesh out the i386 emulation support for ia64. At this point, the only
binary that I know of that fails is cvsup, because the cvsup runtime
tries to execute code in pages not marked executable.
Obtained from: dfr (mostly, many tweaks from me).
administrator to define certain properties of new devfs nodes before
they become visible to the userland. Both static (e.g., /dev/speaker)
and dynamic (e.g., /dev/bpf*, some removable devices) nodes are
supported. Each DEVFS mount may have a different ruleset assigned to
it, permitting different policies to be implemented for things like
jails.
Approved by: phk
one out of a block cipher. This has 2 advantages:
1) The code is _much_ simpler
2) We aren't committing our security to one algorithm (much as we
may think we trust AES).
While I'm here, make an explicit reseed do a slow reseed instead
of a fast; this is in line with what the original paper suggested.
-finstrument-functions instead of -mprofiler-epilogue. The former
works essentially the same as the latter but has a higher overhead
(about 22 more bytes per function for passing unused args to the
profiling functions).
Removed all traces of the IDENT Makefile variable, which had been
reduced to just a place for holding profiling's contribution to CFLAGS
(the IDENT that gives the kernel identity was renamed to KERN_IDENT).
(PROFLEVEL) to kern.pre.mk so that it is easier to manage. Bumped config
version to match.
Moved the check for cputype being configured to a less bogus place in
mkmakefile.c.
- It actually works this time, honest!
- Fine grained TLB shootdowns for SMP on i386. IPI's are very expensive,
so try and optimize things where possible.
- Introduce ranged shootdowns that can be done as a single IPI.
- PG_G support for i386
- Specific-cpu targeted shootdowns. For example, there is no sense in
globally purging the TLB cache for where we are stealing a page from
the local unshared process on the local cpu. Use pm_active to track
this.
- Add some instrumentation for the tlb shootdown code.
- Rip out SMP code from <machine/cpufunc.h>
- Try and fix some very bogus PG_G and PG_PS interactions that were bad
enough to cause vm86 bios calls to break. vm86 depended on our existing
bugs and this was the cause of the VESA panics last time.
- Fix the silly one-line error that caused the 'panic: bad pte' last time.
- Fix a couple of other silly one-line errors that should have caused more
pain than they did.
Some more work is needed:
- pmap_{zero,copy}_page[_idle]. These can be done without IPI's if we
have a hook in cpu_switch.
- The IPI handlers need some cleanup. I have a bogus %ds load that can
be avoided.
- APTD handling is rather bogus and appears to be a large source of
global TLB IPI shootdowns for no really good reason.
I see speedups of between 1.5% and ~4% on buildworlds in a while 1 loop.
I expect to see a bigger difference when there is significant pageout
activity or the system otherwise has memory shortages.
I have backed out a few optimizations that I had been using over the last
few days in order to be a little more conservative. I'll revisit these
again over the next few days as the dust settles.
New option: DISABLE_PG_G - In case I missed something.
keyword and in the description of rp's hints.
Didn't fix rp's hints being mostly in comments so that they are harder to
use (they don't get linted either way because makeLINT.sh strips them and
there is no compile-time syntax checking of hints anyway).
available from bsd.obj.mk.
The native version was identical (and pretty much unused except in
the -DMODULES_WITH_WORLD case, which it is not for "make release")
except that the "bin" -> "base" change of the default DISTRIBUTION
name did not propagate here.
NOTES. Add some comments about the potential problems associated with NIC
driver modules and changing these options.
Fix sorting problems in sys/conf/options with the MSIZE and MCLSHIFT
options.
Reviewed by: bde
