- Factor out code common to all ISA bridge drivers attach methods into a
isab_attach() function.
- Rename the PCI-ISA bridge driver's attach function to pci_isab_attach()
and have it call isab_attach().
interrupt to be used for a device. This is intended solely for internal
use of PCI bus implementations, and exists so that PCI bus drivers
implementing special interrupt assignment methods which require
additional work at the bus level to work right can be easily derived
from the generic driver (or any other one) without resorting to hacks.
It will be used in the sparc64 ofw_pcibus driver, which will be
committed shortly.
Make use of this method in the generic implementation, and add it to
the method table of bus drivers derived from the PCI one.
Reviewed by: imp, -hackers
are some Sun PCI devices around which bogusly set intpin to 0, although
they use the intline mechanism; this allows the device driver to correct
that.
Reviewed by: imp
read permision only required for listing, read/write required for
read/write to registers
fix a possible memory leak
clean up error handling a bit
Reviewed by: silence
Reorder how the pci probing in handled. before adding devices, check to
see if the slot is a multi-function device to see if we should probe all
the functions.
Original idea by: imp
ia64-specific.
- When trying to re-route interrupts, don't change cfg->intline if the
re-route fails by returning an invalid vector. This fixes machines
without any way of routing interrupts such as older PC's without a
$PIR table.
We do not currently write the new intline value back to the hardware, but
we should. That will likely be added in a later commit.
Always route PCI interrupts on i386 UP machines. I was planning to enable
this for i386 anyways once SMP support is done. Having this enabled fixes
problems on many people's laptops.
Requested by: imp
(with other names) in the USB driver sources, but I felt that pcireg.h
should have a complete list - at least of classes and interfaces that we
know about and use.
command config register. At the present, this represents a nop
because these bits should have been set earlier in the process. In
the future, we'll only set these bits when the driver requests the
resource, not when the bus code detects the resource.
Reviewed by: mdodd
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
pci busses implement this.
Also minor comment smithing in cardbus. Fix copyright to this year
with my name on it since I've been doing a lot to this file.
Reviewed by: jhb
We allow the request to go through if it matches either a prefetchable
or a non-prefetchable part of the bridge. We do not check to make
sure it is the right kind of memory because most drivers to not yet
properly set RF_PREFETCHABLE (only cardbus seems to do so, and I'm not
entirely sure it does it right). RF_PREFETCHABLE was invented for
cardbus, so hasn't been properly documented yet.
This is still overridable by hw.pci.allow_unsupported_io_ranges, but
the need for that is greatly reduced, especially for the nvida driver.
Approved by: re
Reviewed by: jhb and many testers
Submitted by: Matt Emmerton (although this has been reworked somewhat)
buses support querying the MAC address in a standard-for-that-bus way.
The base pci bus returns NULL for this IVAR always.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
- If a PCI device is not present, then a 32-bit read_config() is going to
return 0xffffffff not 0xffff.
- For the 82454NX chipset, the MIOC that we read the bus numbers of the
various host-PCI bridges from is at function (slot) 0x10 not 0x0.
Approved by: re (rwatson)
across system suspends on the Intel 82371AB PCI-ISA bridge. On a
Sony Vaio C1XD that I have, these registers are not set correctly
after an ACPI resume. The result is that after resuming, a shared
IRQ is left in edge-triggered mode so the interrupt can later become
jammed in a state where the line remains asserted, but the handler
is never called.
Reviewed by: jhb
supported option and it disabled a whole 2 lines of bootverbose messages.
I wanted to see 1 of the messages (about the latency timers). This
is a wrong place to decode pci configurations, but the code is already
here and handles more details than pciconf(8).
when the first PCI bus attaches.
- Create /dev/pci during MOD_LOAD as well.
- Destroy /dev/pci during MOD_UNLOAD (not that you can kldunload pci, but
might as well get the code right)
- Add an ACPI PCI-PCI bridge driver (the previous driver just handled
Host-PCI bridges) that is a PCI driver that is a subclass of the generic
PCI-PCI bridge driver. It overrides probe, attach, read_ivar, and
pci_route_interrupt.
- The probe routine only succeeds if our parent is an ACPI PCI bus which
we test for by seeing if we can read our ACPI_HANDLE as an ivar.
- The attach routine saves a copy of our handle and calls the new
acpi_pcib_attach_common() function described below.
- The read_ivar routine handles normal PCI-PCI bridge ivars and adds an
ivar to return the ACPI_HANDLE of the bus this bridge represents.
- The route_interrupt routine fetches the _PRT (PCI Interrupt Routing
Table) from the bridge device's softc and passes it off to
acpi_pcib_route_interrupt() to route the interrupt.
- Split the old ACPI Host-PCI bridge driver into two pieces. Part of
the attach routine and most of the route_interrupt routine remain in
acpi_pcib.c and are shared by both ACPI PCI bridge drivers.
- The attach routine verifies the PCI bridge is present, reads in
the _PRT for the bridge, and attaches the child PCI bus.
- The route_interrupt routine uses the passed in _PRT to route a PCI
interrupt.
The rest of the driver is the ACPI Host-PCI bridge specific bits that
live in acpi_pcib_acpi.c.
- We no longer duplicate pcib_maxslots but use it directly.
- The driver now uses the pcib devclass instead of its own devclass.
This means that PCI busses are now only children of pcib devices.
- Allow the ACPI_HANDLE for the child PCI bus to be read as an ivar
of the child bus.
- Fetch the _PRT for routing PCI interrupts directly from our softc
instead of walking the devclass to find ourself and then fetch our
own softc.
With this change and the new ACPI PCI bus driver, ACPI can now properly
route interrupts for devices behind PCI-PCI bridges. That is, the
Itanium2 with like 10 PCI busses can now boot ok and route all the PCI
interrupts. Hopefully this will also fix problems people are having with
CardBus bridges behind PCI-PCI bridges not properly routing interrupts
when ACPI is used.
Tested on: i386, ia64
OOP speak, you would mark these as 'protected' members. Specifically:
- Make the pcib_softc struct public so it can be used by subclasses.
- Make pcib_{read,write}_ivar(), pcib_alloc_resource(), pcib_maxslots(),
and pcib_{read,write}_config() globals that can be used by subclasses.
- Make the pcib devclass a global variable.
- Move most of the pcib_attach() function into a global
pcib_attach_common() function that can be called by the attach routines
of subclasses.
Tested on: i386, alpha, sparc64, ia64
