frequency generation and what frequency the generated was anyones
guess.
In general the 32.768kHz RTC clock x-tal was the best, because that
was a regular wrist-watch Xtal, whereas the X-tal generating the
ISA bus frequency was much lower quality, often costing as much as
several cents a piece, so it made good sense to check the ISA bus
frequency against the RTC clock.
The other relevant property of those machines, is that they
typically had no more than 16MB RAM.
These days, CPU chips croak if their clocks are not tightly within
specs and all necessary frequencies are derived from the master
crystal by means if PLL's.
Considering that it takes on average 1.5 second to calibrate the
frequency of the i8254 counter, that more likely than not, we will
not actually use the result of the calibration, and as the final
clincher, we seldom use the i8254 for anything besides BEL in
syscons anyway, it has become time to drop the calibration code.
If you need to tell the system what frequency your i8254 runs,
you can do so from the loader using hw.i8254.freq or using the
sysctl kern.timecounter.tc.i8254.frequency.
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
This includes:
o mtree (for legal/intel_wpi)
o manpage for i386/amd64 archs
o module for i386/amd64 archs
o NOTES for i386/amd64 archs
Approved by: mlaier (comentor)
and newer CPUs (including Core 2 and Core / Core 2 based Xeons). The
driver attaches to each cpu device and creates a sysctl node in that
device's sysctl context (dev.cpu.N.temperature). When invoked, the
handler binds to the appropriate CPU to ensure a correct reading.
Submitted by: Rui Paulo <rpaulo@fnop.net>
Sponsored by: Google Summer of Code 2007
Tested by: des, marcus, Constantine A. Murenin, Ian FREISLICH
Approved by: re (kensmith)
MFC after: 3 weeks
the 7.0 timeframe.
This is needed because I4B is not locked and NET_NEEDS_GIANT goes away.
The plan is to lock I4B and bring everything back for 7.1.
Approved by: re (kensmith)
- Split out the communication protocols into their own files and use
a couple of function pointers in the softc that the commuication
protocols setup in their own attach routine.
- Add support for the SSIF interface (talking to IPMI over SMBus).
- Add an ACPI attachment.
- Add a PCI attachment that attaches to devices with the IPMI interface
subclass.
- Split the ISA attachment out into its own file: ipmi_isa.c.
- Change the code to probe the SMBIOS table for an IPMI entry to just use
pmap_mapbios() to map the table in rather than trying to setup a fake
resource on an isa device and then activating the resource to map in the
table.
- Make bus attachments leaner by adding attach functions for each
communication interface (ipmi_kcs_attach(), ipmi_smic_attach(), etc.)
that setup per-interface data.
- Formalize the model used by the driver to handle requests by adding an
explicit struct ipmi_request object that holds the state of a given
request and reply for the entire lifetime of the request. By bundling
the request into an object, it is easier to add retry logic to the various
communication backends (as well as eventually support BT mode which uses
a slightly different message format than KCS, SMIC, and SSIF).
- Add a per-softc lock and remove D_NEEDGIANT as the driver is now MPSAFE.
- Add 32-bit compatibility ioctl shims so you can use a 32-bit ipmitool
on FreeBSD/amd64.
- Add ipmi(4) to i386 and amd64 NOTES.
Submitted by: ambrisko (large portions of 2 and 3)
Sponsored by: IronPort Systems, Yahoo!
MFC after: 6 days
and pc98 MD files. Remove nodevice and nooption lines specific
to sio(4) from ia64, powerpc and sparc64 NOTES. There were no
such lines for arm yet.
sio(4) is usable on less than half the platforms, not counting
a future mips platform. Its presence in MI files is therefore
increasingly becoming a burden.
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
lnc(4) on PC98 and i386. The ISA front-end supports the same non-PNP
network cards as lnc(4) did and additionally a couple of PNP ones.
Like lnc(4), the C-bus front-end of le(4) only supports C-NET(98)S
and is untested due to lack of such hardware, but given that's it's
based on the respective lnc(4) and not too different from the ISA
front-end it should be highly likely to work.
- Remove the descriptions of le(4), which where converted from lnc(4),
from sys/i386/conf/NOTES and sys/pc98/conf/NOTES as there's a common
one in sys/conf/NOTES.
into a separate module. Accordingly, convert the option into a device
named similarly.
Note for MFC: Perhaps the option should stay in RELENG_6 for POLA reasons.
Suggested by: scottl
Reviewed by: cokane
MFC after: 5 days
- S3 Savage driver ported.
- Added support for ATI_fragment_shader registers for r200.
- Improved r300 support, needed for latest r300 DRI driver.
- (possibly) r300 PCIE support, needs X.Org server from CVS.
- Added support for PCI Matrox cards.
- Software fallbacks fixed for Rage 128, which used to render badly or hang.
- Some issues reported by WITNESS are fixed.
- i915 module Makefile added, as the driver may now be working, but is untested.
- Added scripts for copying and preprocessing DRM CVS for inclusion in the
kernel. Thanks to Daniel Stone for getting me started on that.
IPI_STOP IPIs.
- Change the i386 and amd64 MD IPI code to send an NMI if STOP_NMI is
enabled if an attempt is made to send an IPI_STOP IPI. If the kernel
option is enabled, there is also a sysctl to change the behavior at
runtime (debug.stop_cpus_with_nmi which defaults to enabled). This
includes removing stop_cpus_nmi() and making ipi_nmi_selected() a
private function for i386 and amd64.
- Fix ipi_all(), ipi_all_but_self(), and ipi_self() on i386 and amd64 to
properly handle bitmapped IPIs as well as IPI_STOP IPIs when STOP_NMI is
enabled.
- Fix ipi_nmi_handler() to execute the restart function on the first CPU
that is restarted making use of atomic_readandclear() rather than
assuming that the BSP is always included in the set of restarted CPUs.
Also, the NMI handler didn't clear the function pointer meaning that
subsequent stop and restarts could execute the function again.
- Define a new macro HAVE_STOPPEDPCBS on i386 and amd64 to control the use
of stoppedpcbs[] and always enable it for i386 and amd64 instead of
being dependent on KDB_STOP_NMI. It works fine in both the NMI and
non-NMI cases.
originally wrote it for 4.x and hasn't really had the time to fully update
it to 5.x and later. Also, the author doesn't use the hardware anymore as
well. If someone does need this driver they can always resurrect it from
the Attic.
Requested by: Frank Mayhar frank at exit dot com
earlier as no one has stepped up to test recent changes to the driver.
Oddly, the module was actually turned on on ia64 though I'm fairly certain
that no ia64 machine has ever had or will ever have an ISA slot.
Axe borrowed from: phk
by Vladimir Dergachev for inclusion in DRM CVS, with minor modifications for
FreeBSD CVS and the appropriate license from Nicolai Haehnle on r300_reg.h.
Fixes hangs when using r300.sf.net userland, tested on a Radeon 9600 on amd64.
