for you to be told there was an error [during verbose boot].
I poked him for the fix, he poked me to get it committed.
Submitted by: Jason Young <doogie@anet-stl.com>
Enhance MIRROR code. Add a few more sanity checks and implement
a zone-based disk selector to make use of both disks when reading.
Also implement a read fail-over. If a read error occurs on one
disk, the I/O is retried on the other.
NOTE: CCD's mirroring support cannot deal with write errors properly
in regards to recovery, meaning that 'old' data under a write error may
be read non-deterministically if you reboot after a write error, and CCD
certainly cannot deal with a disk changeout. And it still can't. Use
vinum if you are really serious about mirroring. CCD basically just
implements a poor-man's mirror.
sum the total amount of I/O issued to determine when all the I/O
has completed. This fails when the EOF boundry occurs in the middle
of an I/O. Using cbp->cb_buf.b_bufsize works better.
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
The lun is not incremented in the ata-disk driver when ATA_STATIC_ID
is not defined, thanks to Kenneth Wayne Culver <culverk@wam.umd.edu>
for finding that one.
PHK pointed at the & problem in atapi-cd in devstat_end_transaction_buf.
Too little sleep I guess...
Phase 1) move the driver
Phase 2)
Phase 3) Profit, by splitting the driver into smaller files like
bktr_tuner, bktr_card, bktr_audio, bktr_<osname>
making it easier to maintain and understand.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
usually cleared by a successful selection, but there is no guarantee
that a future successful selection will ever occur (e.g. empty bus).
The driver never looks at SELINGO, but the busy LED does, so this
change has the cosmetic effect of fixing the rare instance where the
busy LED was left on, confusing the user.
aic7xxx parts. This problem could result in data corruption
during periods of my PCI bus load by busmasters other than the
aic7xxx.
Many thanks to Andrew Gallatin <gallatin@cs.duke.edu> for characterizing
the symptoms of this problem and testing this fix.
adjust the bp->b_bcount the same way for unlabeled VN access as dscheck
does for labeled access.
We also increase the block size to at least 8K for efficiency.
Reviewed by: Tor.Egge@fast.no
- Remove sc_get_scr_stat(). It's not necessary anymore.
- Call ttymalloc() to allocate the struct tty for each vty, rather than
statically declaring an array of struct tty. We still need a statically
allocated struct tty for the first vty which is used for the kernel
console I/O, though.
- Likewise, call ttymalloc() for /dev/sysmouse and /dev/consolectl.
- Delete unnecessary test on the pointer struct tty *tp in some functions.
- Delete unused code in scmouse.c.
WARNING: this change requires you to recompile screen savers!
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
Bug fix: xmradio nolonger experiences a 6Mhz offset after running FXTV
New feature: Automatic Tuner selection for AVerMedia cards with
configuration EEPROMs on (ie the Bt878 based cards)
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
PR: 13793
size != 512 that are configured without a label. The bug should only
have effected swap-backed VN mounts without a label.
Add several major features to VN. In the kernel we add a swap
pre-reservation capability, which can be used to guarentee seek
consistency for swap-backed VN nodes. This also incidently allows
a swap-backed VN filesystem to be recovered after a crash in some
cases (if the same swap blocks happen to be reserved).
We also add a number of new options to vnconfig which do the work
of pre-zeroing or creating/truncating/extending a file which greatly
simplifies using VN in a file-backed configuration.
Add FreeBSD CVS label to sys/sys/vnioctl.h, as well as a new ioctl
flag for the swap pre-reservation feature.
Reviewed by: Alan Cox <alc@cs.rice.edu>, David Greenman <dg@root.com>
warnings caused by the arg having the wrong type (not const enough).
The arg was also wrong (a full name instead of a short one) for calls
from from subr_diskmbr.c and pc98/diskslice_machdep.c.
rewrite the pccard attachment case. This is a work in progress, but
doesn't break the isa case.
I left the #if 0...#endif around the pccard stuff, at Peter's request,
so that normal users don't shoot themselves in the foot.
While I was here:
o Indent a comment to the right location
o Spell Unknown with a final 'n'.
Reviewed by: peter
I have an 82559 card with the same id as the other 8255[78] chips, but
that was made with a date code of 0699 (June 99). The submitter shows
this working with the probe etc, but doesn't actually say it works as
on the ethernet. :-) Assuming it does, this is a RELENG_3 merge candidate.
Submitted by: Steven E Lumos <slumos@sam.ISRI.UNLV.EDU>
this PHY and the Davicom DM9101 have exactly the same register definitions.
One of them is probably a clone of the other. I'm not sure which.
This is needed for the Davicom DM9102 10/100 PCI ethernet driver which
will be committed shortly.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
MCA SCSI adapters.
bt_mca.c is going to live in sys/dev/buslogic instead of sys/dev/mca
as per a conversation with Peter, Doug and Mike.
Thanks to Andy Farkas <andyf@speednet.com.au> for being such a good
sport and doing all the testing for me (as I don't actually own one
of these cards. Yet.)
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
Fix a bug where video capture locks up on channel changes.
Many thanks to Juha for solving this.
Submitted by: Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
New Features:
Greatly improved VBI capture support. (mainly for the AleVT port)
Supports select() on /dev/vbi
Improved RISC program for RGB+VBI capture to capture both evenodd
VBI data even when only capturing even only (or odd only) video
Based on code from Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
Support for Hauppauge 627 and Temic 4006
Submitted by: Maurice Castro <maurice@atum.castro.aus.net>
Bug Fix:
Fix bug in AverMedia card detection.
Break out the detection logic for the aic7855 and properly report
these chips as 7855s instead of 7850s.
The 2940AU_CN is an aic7860 based card, not aic7860.
Not setting CACHETHEN turned out to be a bad idea. It can cause
spurious corruption under heavy PCI load with multiple masters.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best before it kills Matt :-)
Use the specfs routines rather having cloned copies in devfs.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best.
Use the specfs routines rather having cloned copies in devfs.
ones were made by Lucent). The Broadcom chip also appears to use an
internal PHY made by Broadcom which uses the Broadcom OUI. This is different
from previous ASICs which always returned 0 in the PHY ID registers.
To account for this, I added the necessary ID values for the Broadcom
PHY so that it can be detected and attached using the 3Com PHY driver
instead of defaulting to the generic one.
This fixes, at least, panics in ncr_attach() on i386's with about 5MB
of memory. The restriction was a hack to leave some low memory for ISA
DMA, but on i386's we now allocate pages from the top down, so all the
restriction did was cause our allocations to fail when there is no free
memory above 1MB.
some swapper problems analogous to those experienced with ccd.
This fix is a kludge: since we currently don't track the "sector size"
in a volume label, we guess a worst case (4 kB, as used by vnode
devices). If the concept of sector size is here to stay, I'll make
some changes to track the "sector size" of a volume. This will
probably be the maximum of the sector sizes of all component drives,
but things could get ugly if we start allowing non-standard sector
sizes such as 524 bytes.
Unkludged-version-submitted-by: phk
ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is
a port of the NetBSD driver with various hacks. The ML driver is necessary
to support the Olicom OC-2326 ThunderLAN-based NIC.
Also regenerated miidevs.h to pick up the proper 'obtained from'
revision string.
lockrange: correctly expand rangelock struct, including expanding a
null struct. Previously lockrange would attempt to lock a
NULL pointer under these circumstances.
Reported-by: Ian Freislich <iang@uunet.co.za>
initialized subdisks.
Tidy up some comments.
Eliminate sddownstate(); it wasn't being used any more. Return
REQUEST_DOWN instead.
Add setstate_by_force() to implement the VINUM_SETSTATE_FORCE ioctl
for diddling individual object states. This is a repair tool which
can also be used for panicing the system. Use with utmost care if at
all.
avoids a race condition where multiple RAID-5 subdisks are being
revived at the same time. The locks should also prevent conflicts
with user requests on concatenated and striped plexes, but this needs
more work.
Tidy up some comments.
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
instead, use generic entry points for all drivers.
- Eliminate bogus makedev().
- Eliminate softc in the lower drivers, as it is no longer necessary.
Submitted (95%) by: phk
MII-compliant PHY drivers. Many 10/100 ethernet NICs available today
either use an MII transceiver or have built-in transceivers that can
be programmed using an MII interface. It makes sense then to separate
this support out into common code instead of duplicating it in all
of the NIC drivers. The mii code also handles all of the media
detection, selection and reporting via the ifmedia interface.
This is basically the same code from NetBSD's /sys/dev/mii, except
it's been adapted to FreeBSD's bus architecture. The advantage to this
is that it automatically allows everything to be turned into a
loadable module. There are some common functions for use in drivers
once an miibus has been attached (mii_mediachg(), mii_pollstat(),
mii_tick()) as well as individual PHY drivers. There is also a
generic driver for all PHYs that aren't handled by a specific driver.
It's possible to do this because all 10/100 PHYs implement the same
general register set in addition to their vendor-specific register
sets, so for the most part you can use one driver for pretty much
any PHY. There are a couple of oddball exceptions though, hence
the need to have specific drivers.
There are two layers: the generic "miibus" layer and the PHY driver
layer. The drivers are child devices of "miibus" and the "miibus" is
a child of a given NIC driver. The "miibus" code and the PHY drivers
can actually be compiled and kldoaded as completely separate modules
or compiled together into one module. For the moment I'm using the
latter approach since the code is relatively small.
Currently there are only three PHY drivers here: the generic driver,
the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding
others later as I convert various NIC drivers to use this code.
I realize that I'm cvs adding this stuff instead of importing it
onto a separate vendor branch, but in my opinion the import approach
doesn't really offer any significant advantage: I'm going to be
maintaining this stuff and writing my own PHY drivers one way or
the other.
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.
Retire the at_shutdown family of functions and replace them with
new event handler lists.
Rework kern_shutdown.c to take greater advantage of the use of event
handlers.
Reviewed by: green
Notice that 'unit' wasn't defined once I changed the parameters of the func.
These things make me feel like wading in with a flamethrowr or something.
Too much cruft!
</rant>
if_init_f_t is passed void * containing the address of ifp->if_softc
not the unit number.
Someone tell me if these things don't work as I don't have the hardware
needed to test them. (thats a first.)
I'll get if_ze and if_zp later.
Pointed out by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
to achieve a delay is pretty mean.
Andrew reports:
"The tulip_delay_300ns() is, well, bloody stupid on machines with a
heavily loaded PCI bus. It tries to do a delay by assuming PCI reads
will take a certain amount of time & issues a large amount of
(expensive, 5% CPU when your PCI bus is heavily loaded) pci reads.
Locally, we've replaced the calls to tulip_delay_300ns(sc) in the EMIT
macros with a simple DELAY(1) and not seen any problems. Plus we've
gained about 50Mb/sec throughput on our gigabit network cards because
of the added PCI bus bandwidth available."
Also, I do not understand why, but this change appears to stop the
Transmit Fifo underrun on one of my systems (but not the Alpha PC164SX).
This shouldn't make that much of a difference since the mii bus isn't
touched all that often, but perhaps when it does get accessed and hence
hammers the register, it was causing the chip to get upset.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
about a dev_t.
printf("%x", dev) now becomes printf("%s", devtoname(dev)) because
printing actual information about the device is much more useful then
printing a pointer to an address that would never help the developer debug.
Submitted by: phk, bde
messages, abort messages, and abort tag messages.
Fix a bug in how default transfer negotiations are handled if the
user had disabled initial bus resets.
Support multi-targetid on the aic7895C.
format_config: code preening.
vinum_scandisk: If we find a partition in the first pass over a drive,
note the fact so we don't grab the compatibility partition as well.
Submitted-by: peter
the aic7890/91/96/97 cards. This could cause the system to go into
a long retry/recovery loop during probe.
Fix the alignment argument to bus_dma_tag_create().
Don't set the CACHETHEN bit in dscommand0 for Ultra2 controllers
until we know more about its behavior. The description for this
bit makes it sound like it could cause problems with certain
PCI chipsets.
goes into initialized state, not 'up'. This makes it easier to ensure
consistency in multi-plex volumes.
update_plex_state: redo transitions from empty and initialized
subdisks to up or reviving, depending on the number of plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
Don't return "can't do it" when the user requests a state change to
the current state. This previously caused silly messages like "Can't
start <foo>: invalid argument", when in fact <foo> was already
started.
set_plex_state: don't set state for non-existent plexes.
update_plex_status: as long as we have initializing subdisks, we're
initializing.
Move the declaration of freerq() to request.h.
logrq: add support for lock events.
vinumstart: solve a problem where removing a plex from an active
volume could cause attempts to access non-existent plexes.
launch_requests: don't set a request group active until we're sure we
can launch it. This caused some hangs under unusual
circumstances.
bre: don't set XFR_BAD_SUBDISK if we're not going to use it.
build_read_request: correct recovery, which caused some hangs under
(other) unusual circumstances.
build_rq_buffer: don't set bp->b_dev if we don't have a dev.
sdio: clean up, remove obsolete code.
deallocrqg: unlock any locks the rqg may have.
bre5:
Shorten some lines.
Desired-by: bde
If we're reading from a short plex, return EOF indication.
Always lock the stripe before starting a transfer. Hopefully the
current version will solve some data integrity problems that have
been reported with degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
solve some data integrity problems that have been reported with
degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Tidy other comments.
open_drive: don't call set_drive_state if we decide to take it down.
This could help avoid some race conditions with the daemon.
init_drive: don't set the drive down, we'll let close_locked_drive do
that.
close_locked_drive: set drive state to down without calling
set_drive_state. This could help avoid some race conditions with the
daemon.
driveio: remove the function, it wasn't being used.
get_volume_label: remove volume dependencies so that we can return a
label for plexes and subdisks as well. What a kludge.
Remove declarations for freerq and free_rqg.
Remove DEBUG_RESID code.
freerq: check whether the request is holding a lock, free if so.
free_rqg: remove. It wasn't being used any more.
Change the Debugger calls to panics.
checkdiskconfig(): remove. It didn't make any sense to complain about
kernel keywords in user config files; it just made it more difficult
to convert. Now we ignore kernel keywords if we're not in kernel
mode.
get_empty_sd: initialize sectors.
free_drive: don't close if we don't have a vp. Maybe this will help
fix the problem that peter had, but I wouldn't count on it.
config_plex: If the plex is RAID-5, give it a rangelock structure.
start_config: Reset current drive, plex and volume so that a new
'create' command doesn't get long-dead defaults.
struct rqelement, enum rqinfo_type, struct rqinfo, union rqinfou: add
lock requests.
Add declarations for freerq and unlockrange. Since they include
request structures, they can't go in vinumext.h
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
- %q -> %ll.
Fixed nearby errors not reported by gcc -Wformat on i386's:
- don't assume that the promotion of [u_]int64_t is [u_]quad_t.
- don't use signed formats for unsigned args.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
update_plex_state:
If any subdisk in the plex is initializing, set the plex to
initializing state. This gets rid of the ugly corrupt/degraded/up
transitions which previously occurred.
Desired-by: Steve Taylor <staylor@cybernet.com>
sddownstate:
Add new function, used by checksdstate.
checksdstate:
Let sddownstate decide what status to return.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
logrq: save device major and minor numbers to compensate for lost
dev_t.
launch_requests: Don't issue requests which are marked
XFR_BAD_SUBDISK. This may make things easier in bre().
bre:
Rearrange.
- Change some comments
- Recognize holes in plex structure. Formerly this could lead to
incorrect write to the plex. Return REQUEST_DEGRADED on a read
request, but carry on to the bitter end on a write request, and
mark the requests for the inaccessible subdisks with
XFR_BAD_SUBDISK.
- return REQUEST_EOF if the requested transfer goes beyond the end
of the plex. This is not an error, since other plexes may go
further into the volume address space.
build_read_request:
Handle REQUEST_DEGRADED returned from bre().
sdio:
Lock buffer before issuing the requests.
will only accept partitions of type 'vinum'.
format_config: Use the new %q format option in kvprintf, thus getting
rid of some of the filthiest code I've written in a long time. Also
remove the lltoa() function.
With-great-thanks-to: peter
format_config: Accept the fact that a subdisk might not be attached to
a plex, and save the config correctly.
vinum_scandisk: Scan all slices on a drive with a Microsoft partition
table. Only look at the compatibility slice if nothing was found in
the Microsoft slices.
This change removes a frequently employed method of shooting
yourself in the foot: people would decide that the Vinum drives
belonged on their own slice, and they wouldn't be able to start the
subsystem after a reboot. Documentation updates to follow.
initialize subdisks. Probably the plex-related subdisk type will die
a death.
vinumconfig.c:
Accept (and ignore) kernel state information in userland config
files. This saves a lot of error recovery and also makes it possible
to use the output of printconfig to create new configuration.
Remove checkdiskconfig(). It wasn't needed any more.
Start adding support for hot spare drives. You can't put anything on
them (yet).
Change message formats from %lld to %qd.
get_empty_sd: Initialize size to -1. Previously this was done in
config_subdisk, which is the wrong place.
start_config: set current drive, plex and volume to -1, thus stopping
update configurations from taking their defaults from old configs.
now used in f_ops in place of NULL, and modifications to the files
are more carefully ordered. f_ops should also be set to &badfileops
upon "close" of a file.
This does not fix other problems mentioned in this PR than the first
one.
PR: 11629
Reviewed by: peter
eisa_add_intr() which now takes an additional arguement (one of
EISA_TRIGGER_LEVEL or EISA_TRIGGER_EDGE).
The flag RR_SHAREABLE has no effect when passed to
bus_alloc_resource(dev, SYS_RES_IRQ, ...) in an EISA device context as
the eisa_alloc_resource() call (bus_alloc_resource method) now deals
with this flag directly, depending on the device ivars.
This change does nothing more than move all the 'shared = inb(foo + iobsse)'
nonesense to the device probe methods rather than the device attach.
Also, print out 'edge' or 'level' in the IRQ announcement message.
Reviewed by: dfr
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
critical mbuf fields to sane values. Simplify the use of ETHER_ALIGN to
enforce payload alignment, and turn it on on the x86 as well as alpha
since it helps with NFS which wants the payload to be longword aligned
even though the hardware doesn't require it.
This fixes a problem with the ti driver causing an unaligned access trap
on the Alpha due to m_adj() sometimes not setting the alignment correctly
because of incomplete mbuf initialization.
the driver_t declaration should be "skc" not "sk". Technically, "skc"
is the parent PCI device (the SysKonnect GEnesis controller) and "sk0"
and "sk1" are the network interfaces that get attached to it.
the device numbers are now minor number only, so that we can still
compare them after dev_t has turned into a blob.
Broken-by: dev_t changes
Reported-by: Vallo Kallaste <vallo@matti.ee>
"Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
by removing a floppy that as being operated on.
The spagghetti is hardly understandable at all anymore, so i can't
100 % ascertain this is really the Right Thing to do, maybe our new
floppy driver maintainer, Jesus Monroy Jr can do this. :-))
The structure is the right length, but some of the members (notably
wi_q_info) were off a bit. This causes the received signal strength
values to appear bogus.
vnodes referencing this device.
Details:
cdevsw->d_parms has been removed, the specinfo is available
now (== dev_t) and the driver should modify it directly
when applicable, and the only driver doing so, does so:
vn.c. I am not sure the logic in checking for "<" was right
before, and it looks even less so now.
An intial pool of 50 struct specinfo are depleted during
early boot, after that malloc had better work. It is
likely that fewer than 50 would do.
Hashing is done from udev_t to dev_t with a prime number
remainder hash, experiments show no better hash available
for decent cost (MD5 is only marginally better) The prime
number used should not be close to a power of two, we use
83 for now.
Add new checkalias2() to get around the loss of info from
dev2udev() in bdevvp();
The aliased vnodes are hung on a list straight of the dev_t,
and speclisth[SPECSZ] is unused. The sharing of struct
specinfo means that the v_specnext moves into the vnode
which grows by 4 bytes.
Don't use a VBLK dev_t which doesn't make sense in MFS, now
we hang a dummy cdevsw on B/Cmaj 253 so that things look sane.
Storage overhead from all of this is O(50k).
Bump __FreeBSD_version to 400009
The next step will add the stuff needed so device-drivers can start to
hang things from struct specinfo
interrupts that were scheduled. Testing shows it didn't really do very much
and it makes the code a little more complicated (which is never a good thing).
Also fix the rambuffer offset initialization for the 512K/64K SRAM case
(512K total using 64K chips). It should be 0. The only case with a
non-standard rambuffer offset address is 1024K/64K according to the
SysKonnect manual. (My card has the 1024/64 configuration and I don't know
which card uses the 512/64 configuration, if any, so I'm not sure that
this was really a problem for anyone.)
Change number of VBI lines from 16 to 12 for NTSC formats.
Juha.Nurmela@quicknet.inet.fi found/fixed bug in VBI_SLEEP.
New features
MSP3430G DBX initialisation from Matt Brown <matt@dqc.org>
STB Bt878 card identification.
Hauppauge Model Number identification.
Changes to probeCard() for better eeprom identification.
Experimental TDA9850 initialisation code, from Linux bttv.
Cross Platform Changes
The driver has been reorgainsed based ideas from Brad Parker's port to Linux
to seperate OS Dependant and Independant sections.
I have backends for FreeBSD 2.2.x/3.x and 4.x newbus, BSDI, OpenBSD and NetBSD.
This commit has FreeBSD 2.2.8/2.2-stable/3.x and FreeBSD 4.x newbus backends.
Some code submitted by: Juha.Nurmela@quicknet.inet.fi
Matt Brown <matt@dqc.org>
Brad Parker <brad@parker.boston.ma.us>
Some code obtained from: Linux bttv driver
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
- Correctly observe the variable `extra_history_size' when changing
the size of history (scroll back) buffer.
- Added sc_free_history_buffer().
Pointed out by: des
in ti_rxeof() instead. This doesn't really seem to provide much in the
way of a performance boost, and I'm pretty sure it can cause mbuf leakage
in some extreme cases.
frames (or just insane received packet lengths generated due to errors
reading from the NIC's internal buffers). Anything too large to fit
safely into an mbuf cluster buffer is discarded and an error logged.
I have not observed this problem with my own cards, but on user has
reported it and adding the sanity test seems reasonable in any case.
Problem noted and patch provided by: Per Andersson <per@cdg.chalmers.se>
isp_io_map, isp_no_fwload, isp_fwload, isp_no_nvram, isp_fcduplex
which are all bitmaps of isp instances that should or shouldn't
map memory space, I/O space, not load f/w, load f/w, ignore nvram,
not ignore nvarm, set full duplex mode. Also have an isp_seed value
that we can use to generate a pseudo seed for a synthetic WWN.
Other minor cosmetic cleanup. Add in support for the Qlogic ISP
2200. Very important change where we actually check now to see
whether we were successful in mapping request and response queues
(and fibre channel scratch space).
not having SCSI_ISP_SCCLUN config defined if we don't have f/w for
the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change
the way the default LoopID is gathered (it's now a platform specific
define so that some attempt at a synthetic WWN can be made in case
NVRAM isn't readable).
Change initialization of options a bit- don't use ADISC. Set
FullDuplex mode if config options tells us to do so. Do not use
FULL_LOGIN after LIP- it's the right thing to do but it causes too
much loop disruption (Loop Resets). Sanity check some default
values. Redo construction of port and node WWNs based upon what we
have- if we have 2 in the top nibble, we can have distinct port
and node WWNs. Clean up some SCCLUN related code that we obviously
had never compiled (:-(). Audit commands coming int ispscsicmd and
don't throw commands at Fibre devices that do not have Class 3
service parameters TARGET ROLE defined.
Clean up f/w initialization a bit. Add Fabric support (or at least
the first blush of it). Whew - way too much to describe here.
Basically, after a LIP, hang out until we see a Loop Up or a Port
DataBase Change async event, then see if we're on a Fabric
(GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric
controller for fabric devices using the GetAllNext SNS subcommand.
As we find devices, announce them to the outer layer. Try and do
some guard code for broken (Brocade) SNS servers (that get stuck
in loops- gotta maybe do this a different way using the GP_ID3 cmd
instead). Then do a scan of the lower (local loop) ids using a
GET_PORT_NAME to see if the f/w has logged into anything at that
loop id. If so, then do a GET_PORT_DATABASE command. Do this scan
into a local database. At this point we can say the loop is 'Ready'.
After this, we merge our local loop port database with our stored
port database- in a as yet to be really fully exercised fashion we
try and follow the logic of something having moved around. The
first time we see something at a Loop ID, we fix it, for the purpose
of this system instance, at that Loop ID. If things shift around
so it ends up somewhere else, we still keep it at this Loop ID (our
'Target') but use the new (moved) Loop ID when we actually throw
commands at it. Check for insane cases of different Loop IDs both
claiming to have the same WWN- if that happens, invalidate both.
Notify the outer layer of devices that have arrived and devices
that have gone away. *Finally*, when this is done, search the
softc's database of Fabric devices and perform logout/login actions.
The Qlogic f/w maintains logout/login for all local loop devices.
We have to maintain logout/login for fabric devices- total PITA.
Expect to see this area undergo more change over time.
Change some fcp parameter structures such that we can get the portid
(24 bit value), get both node and port WWN, know whether we're on a fabric
or not, note whether we've ever seen the loop up, and note the current
state of the loop.
Replace the isp_pdb_t structure in fcparams with a reduced cost structure
that maintains a static relationship to 'Target', but can have the actual
loop ID used change (in case, post LIP, we discover things have moved
around). This also retains portid and node/port WWNs. This array gets
larger if we have fabric support compiled in.
Note special loop IDs that are invariate for this device- FL_PORT_ID
(0x7e) which tells us if there's a fabric controller present, FC_PORT_ID
and FC_SNS_ID (fabric controller port and fabric SNS server port). We don't
use the latter two for anything. IDs above FC_SNS_ID up through 255 are
available for mapping fabric devices to 'target' ids.
Add in a config define to set FC full duplex mode. Add in a define to
recognize the Qlogic 2200 boards. Add comments about ISPCTL commands.
Add and change some ISPASYNC enumes.
compiles cleanly on the Alpha. (On the alpha, the port type is an int,
not a short).
Cast a couple of pointers to ints via 'uintptr_t' rather than 'unsigned
int' since uintptr_t is long (64 bit) on Alpha, as are pointers.
Correct race condition between caller and daemon.
Tripped-over-by: Zach Heilig <zach@uffdaonline.net>
Bernd Walter <ticso@cicely.de>
Niels Chr. Bank-Pedersen <ncbp@bank-pedersen.dk>
lockmgr locks. This commit should be functionally equivalent to the old
semantics. That is, all buffer locking is done with LK_EXCLUSIVE
requests. Changes to take advantage of LK_SHARED and LK_RECURSIVE will
be done in future commits.
The atapi subsystem has gotten better error handeling and timeouts,
it also tries a REQUEST SENSE command when devices returns errors,
to give a little more info as to what went wrong. It might be a
little verbose for now, but I'm interested in as much feedback on
errors as possible, especially timeouts, as I'm a bit in doubt if
I've chosen resonable default values everywhere.
The disk driver has been changed a bit to prepare for tagged queing,
which is next on my list.
The disk driver has grown a dump routine, I got one implementation
from Darrell Anderson <anderson@cs.duke.edu> which also did
partial dumps (usefull on big memory machines) I left out the
partial stuff for now, and changed the rest alot to fit into the new
ad_request framework.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
-Søren
and insertion should affect the line the cursor is on only.
This change should have been committed together with syscons.c rev 1.308.
(I forgot to do so, when I committed syscons.c :-(
Pointed out by: sos
If the drive goes down, queue a close to the daemon. In many cases
this function gets called in process context, so it could do it
directly, but it's more trouble finding out where we came from than
getting the daemon to do it.
Don't bzero the buffer structure, it's been done already by
allocrqg.
sdio:
Build up a correct buffer header, don't steal linkages from system
buffer headers.
Noticed-by: mckusick
* Conformance with Dingo specification. This includes:
Collision/error statistics gathering.
Multicast address filtering, eg. the hash filter.
Initialisation and interrupt handling sequences.
Note that I've started on some of this already in v1.20.
* The probe routine needs some more work, to identify oddities such as the
REM10.
* There are still problems with the autonegotiation code; specifically, it
won't autonegotiate with some 10/100 hubs. This might simply be the hardware
not getting along, in which case there's nothing we can do, but it's still
worth investigating
* CEM28/CEM33 support. Should be able to integrate this directly from the
Linux code.
* Performance enhancements:
Full-duplex on 10Mbit networks.
Virtual shared-memory mode.
Early send and receive modes.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
* Conformance with Dingo specification. This includes:
Collision/error statistics gathering.
Multicast address filtering, eg. the hash filter.
Initialisation and interrupt handling sequences.
Note that I've started on some of this already in v1.20.
* The probe routine needs some more work, to identify oddities such as the
REM10.
* There are still problems with the autonegotiation code; specifically, it
won't autonegotiate with some 10/100 hubs. This might simply be the hardware
not getting along, in which case there's nothing we can do, but it's still
worth investigating
* CEM28/CEM33 support. Should be able to integrate this directly from the
Linux code.
* Performance enhancements:
Full-duplex on 10Mbit networks.
Virtual shared-memory mode.
Early send and receive modes.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
fix; it doesn't address the problem of removing the module. If you do
the following:
vinum stop
fsck /dev/vinum/VOLUME
you *will* get a system crash. What we need is a cdevsw_remove
corresponding to cdevsw_add, but that hasn't been written yet.
Submitted-by: phk
usbd_get_interface_descriptor
2) remove soft reset. It's been dropped from the USB Mass Storage Bulk-Only
Specification
3) move the clear feature halt to the reset routine.
positively not let ti_encap() fill up the TX ring all the way and wrap
around. This fixes a potential transmit lockup where a really fast
machine (or particular TX traffic pattern) can overrun the end of the
ring.
Reported by: John Plevyak <jplevyak@inktomi.com>
Also removed the BSDI support (for now)
This allows the driver to be loaded/unloaded as a KLD
and loaded in the boot loader phase whithout making a custom kernel.
corresponding variable `rc_wakeup_started' in rev.1.36 but broken
again in rev.1.37. This bug only caused excessive polling (it gave
NRC activations for each of the SWI handler and the timeout handler
instead of 1 of each).
Moved cdevsw attachment from the driver probe routine to the driver
attach routine.
