Also, add definitions for more bits of UCHCOM_REG_LCR1 as seen in the
Linux driver. UCHCOM_LCR1_PARENB definition was different from that in
the Linux driver and clashed with newly added UCHCOM_LCR1_RX. I took a
liberty to change UCHCOM_LCR1_PARENB to the Linux definition as it was
unused in the driver anyway. This change should make
uchcom_cfg_set_break() easier to understand.
Approved by: hselasky
MFC after: 2 weeks
Product IDs are specified in vendor documents. The previously used
device ID is not. This is a cosmetic change. No functionality depends
on those IDs.
Reviewed by: hselasky
MFC after: 2 weeks
muge was committed to the tree in r333713 but not yet connected to the
tree, and it crossed paths with the migration to using ck.
Sponsored by: The FreeBSD Foundation
Microchip provided a permissively-licensed lan78xx header, which has
an 'ETH_' prefix on most definitions. Follow suit in our driver.
Sponsored by: The FreeBSD Foundation
storage, CDC ACM (serial), and CDC ECM (ethernet) at the same time.
It's quite similar in function to Linux' "g_multi" gadget.
Reviewed by: hselasky@
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
one character too many. Note that this function is only used to decode
string descriptors generated by the kernel itself.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
This driver supports two Microchip USB-Ethernet controllers:
LAN7800 USB 3.1 to 10/100/1000 Mbps Ethernet
LAN7515 USB 2 to 10/100/1000 Mbps Ethernet with built-in USB hub
The LAN7515 is the Ethernet controller on the Raspberry Pi 3B+.
At present there is no datasheet for the LAN7515, but it is effectively
a USB 2 hub combined with a LAN7800 controller. A comprehensive LAN7800
datasheet is at http://www.microchip.com/wwwproducts/en/LAN7800.
This driver is based on the structure of the smsc(4) driver which
supports Microchip/SMSC's LAN95xx family. (Microchip acquired SMSC
in May 2012.) The Linux lan78xx driver served as a reference for some
functionality and registers.
The 'muge' driver name comes from "Microchip USB Gigabit Ethernet".
I made some style adjustments and minor edits to Arshan's submission.
It will be connected to the build after additional review and testing.
Thanks to Microchip for providing a number of Evaluation Boards (EVBs)
for development and testing.
Submitted by: Arshan Khanifar
Reviewed by: hselasky (earlier)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15168
LAN7800 USB 3.1 to 10/100/1000 Ethernet with PHY
LAN7801 USB 3.1 to 10/100/1000 Ethernet with RGMII interface
Also update manufacturer name for the Vendor ID. Microchip acquired
SMSC in May 2012.
Sponsored by: The FreeBSD Foundation
through a SYSCTL instead of a compile time define.
Add quirk by default for all LynxPoint XHCI controllers.
PR: 227602
MFC after: 3 days
Sponsored by: Mellanox Technologies
Per the datasheet, the BUSY bit must be set when reading or writing PHY
registers. From Linux commit 80928805babf.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15217
In smsc_phy_init function, when the driver was trying to reset PHY, it
didn't poll for the correct bit (BMCR_RESET) to be cleared. Instead, it
anded it with MII_BMCR (which is 0), so it just exited the loop.
This issue was fixed in Linux in commit d94609200069.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
device-side (and only device-side) "virtual USB serial adapters" - the
ones you can get with an OTG-capable board - as consoles. It boils down
to adding the device name to kern.console sysctl, although doing that
requires jumping through some hoops. It doesn't change the actual
operation of those virtual devices. The point is to make it possible
for init(8) to recognize them as console devices and to launch getty(8)
for them, when configured as "onifconsole" in ttys(5). The point of
that, in turn, is to add such entries to the default ttys(5), so that
init(8) will launch gettys for device-side "virtual serial adapters",
but not for actual USB serial dongles.
Reviewed by: hselasky@
No objections: imp@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
A series of zero delay callouts can happen causing high CPU usage of the
timer subsystem when trying to repeat keys, because the time of the
absolute timeout is not moving forward. The condition clears when all
keys are released.
Reported by: Johannes Lundberg <johalun0@gmail.com>
Discussed with: bde@
PR: 226968
MFC after: 1 week
Sponsored by: Mellanox Technologies
endpoints. The Allwinner driver will need to set this as the EPINFO
register isn't useful there.
Submitted by: jmcneill
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D5881
On the Allwinner SoCs we need to set a custom endpoint configuration. To
allow for this use a table to store the configuration so the attachment
can override it.
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14783
Move copy-pasted code for RTS/CTS frame allocation into net80211.
While here, add stat / debug message for allocation failures
(copied from run(4)) + return error here in bwn(4).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D14628
the jtag port, so that a tty is not created for it.
This is based on information in the PR and from the vendor website. When
the PR was first opened we had no facility for flagging the jtag ports. I
stumbled across the still-open PR with the idea of closing it, and noticed
that this wee update was needed.
PR: 175893
network device pointer might be NULL. Wait for any pending tasks to
complete before calling axge_stop().
MFC after: 1 week
Sponsored by: Mellanox Technologies
would be safe, but the function also tries to destroy mutexes that never
got created).
I guess this can only happen when imx_ehci_detach() is called on the
error-exit path from imx_ehci_attach(), and that path never got exercised
before today.
artificial NOMATCH usb does in lieu of creating a device_t for devices
with no drivers. Also, correct bus to be 'uhub' since where USB
devices attach, even though 'usb' is more logical, we need the
physical bus here.
Submitted by: hps@