install of Postfix fails since Postfix 1 is picked from INDEX instead
of Postfix 2.
The problem is that the package_add function matches multiple Postfix
packages and then installs a "random" version (the last one found in
INDEX). This does not occur with a CD-ROM install since there is only
one Postfix package on the CD-ROM.
The correct solution to this would be to check the origin field from
INDEX instead of the package name, but due to the way sysinstall is
made that is not trivial, so instead work around the problem by
hard-coding the Postfix major and minor revision (for the current
stable version) to install directly into the package_add call.
PR: misc/65426
Reported by: Harold Kachelmyer <bugs@princessharold.net>
Approved by: trhodes
chipsets, based on Linux's via-agp.c. On boot, the system selects which AGP
version to use based on the inserted card. If v2 was chosen, the chipset
needs to be programmed with the v2 registers still. Also included in kern/69953
are changes to make the programming of the v3 registers match linux, but that
will be left out until the need to do so is confirmed (want specs or a tester).
PR: kern/69953
Submitted by: Oleg Sharoiko <os@rsu.ru>
Tested by: Oleg Sharoiko <os@rsu.ru>, Geoff Speicher <geoff@speicher.org>
(full version from PR)
The hardware always gives read access for privilege level 0, which
means that we cannot use the hardware access rights and privilege
level in the PTE to test whether there's a change in protection. So,
we save the original vm_prot_t in the PTE as well.
Add pmap_pte_prot() to set the proper access rights and privilege
level on the PTE given a pmap and the requested protection.
The above allows us to compare the protection in pmap_extract_and_hold()
which was missing. While in pmap_extract_and_hold(), add pmap locking.
While here, clean up most (i.e. all but one) PTE macros we inherited
from alpha. They were either unused, used inconsistently, badly named
or simply weren't beneficial. We save the wired and managed state of
the PTE in distinct (bit) fields.
While in pte.h, s/u_int64_t/uint64_t/g
pmap locking obtained from: alc@
feedback & review by: alc@
* Allow no-fault wiring/unwiring to succeed for consistency;
however, the wired count remains at zero, so it's a special case.
* Fix issues inside vm_map_wire() and vm_map_unwire() where the
exact state of user wiring (one or zero) and system wiring
(zero or more) could be confused; for example, system unwiring
could succeed in removing a user wire, instead of being an
error.
* Require all mappings to be unwired before they are deleted.
When VM space is still wired upon deletion, it will be waited
upon for the following unwire. This makes vslock(9) work
rather than allowing kernel-locked memory to be deleted
out from underneath of its consumer as it would before.
or 'env MAKEOBJDIRPREFIX=... make' depending on the setting of
MAKEOBJDIRPREFIX in the environment. In any case this line kills the
original value of ${MAKE}. When during buildworld a new make is built (as
is the case during the upgrade) this causes a wrong make to be picked up
(the first one in the path). Use the same technique as Makefile.inc1:
create a MAKEENV variable and a CRUNCHMAKE that calls ${MAKE} with that
MAKEENV prefixed. Use CRUNCHMAKE instead of MAKE throughout the generated
makefile. This leaves the original ${MAKE} undisturbed.
1. Move a comment to its proper place, updating it. (Except for white-
space, this comment had been unchanged since revision 1.1!)
2. Remove spl calls.
fix the obvious bugs, nastier ones reside below the surfac), and having
it commented out here just encourages people to try it.
# I'm not removing it from the base system, yet.
as environment variables and should not be set on make's command
line. They happen to work accidentially as command line variables
too when none of the sub-makes wants to play games with them (because
make is putting command line variables into the environment and will
find them there later on). Makefile.inc1 wants to change
MAKEOBJDIRPREFIX. In this case one cannot set it on the command line.
For incoming packets, the packet's source address is checked if it
belongs to a directly connected network. If the network is directly
connected, then the interface the packet came on in is compared to
the interface the network is connected to. When incoming interface
and directly connected interface are not the same, the packet does
not match.
Usage example:
ipfw add deny ip from any to any not antispoof in
Manpage education by: ru
on March 31 won't take you to March 2 or 3 (now the result will
be the last day of February.)
In general, now stepping by months from the last days of the current
month A will take you to the very last day of the target month B if
B is shorter than A.
The previous version would just step to March 31 and rely on mktime(3)
to correct the date. Despite its simplicity, such way was counter-intuitive
to users and caused pain to shell script writers.
Noticed by: Igor Timkin <ivt at gamma dot ru>
Approved by: brian
MFC after: 2 weeks
not "make world", as the first step of building the release.
While here, remove another mention of "make world", as the
latter is no longer supported by src/Makefile.
two -n flags. If only one -n flag is given the old behaviour
is retained (POLA). In order to make this working for installworld
change the IMAKEENV in this case so that the tools are found
(we have no temporary installation environment in this case).
Submitted by: ru (IMAKEENV part)
It allows to fix problems when last provider's sector is shared between few
providers.
- Bump version number for CONCAT and STRIPE and add code for backward
compatibility.
- Do not bump version number of MIRROR, as it wasn't officially introduced yet.
Even if someone started to play with it, there is no big deal, because
wrong MD5 sum of metadata will deny those providers.
- Update manual pages.
- Add version history to g_(stripe|concat).h files.
given -n. For POLA reasons this behaviour is switched on only when
at least two -n flags are given to make. One -n flag keeps the old behaviour
of showing the shell command that would recurse into the sub-directories.
Discussed with: ru
