o Honor NE2000DVF_{AX88190,DL10019} flags by setting the ED_FLAGS_xxxx
flag.
o Mark linksys combo_ecard as ax88190
o Set the type_str to AX88190 for the ax88190 cards.
This fixes ax88190 based cards, for the most part, but doesn't seem to fix
the mii based dl10019 cards (aka linksys cards).
card is ejected while we're in this routine.
yamamoto-san's original patch had a small race window for AX88190
chips, which I corrected by limiting the number of iterations we'd try
to reset the bits to be about 15ms rather than forever. This seems to
work for me, but I don't have a large collections of cards based on
this chipset.
Submitted by: YAMAMOTO Shigeru
built without support for miibus PHYs. Most ed cards don't need
miibus support, so it's useful to be able to avoid the bloat of
all the mii devices for small fixed-purpose kernels.
storing a flag in the global variable 'linksys' during the probe
routine and reading it during the attach routine. We now have the
ED_VENDOR_LINKSYS vendor code stored in sc->vendor, so check that
instead.
not from the probe routine. This was an oversight when I originally
ported the miibus support to -current, though it was mostly harmless.
We now set the vendor code to the new value ED_VENDOR_LINKSYS in
ed_pccard_Linksys() at probe time. Then ed_pccard_attach() checks
the vendor code, and sets up the miibus if appropriate.
Reviewed by: imp
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
* a ">" is really ">=" ;
* do not try to fetch zero-sized blocks from the card;
* make sure that bpf gets the packets it wants even with
bridging active;
o Move the ax88190 code to its own function.
o Move all device_method_t, driver_t and DRIVER_MODULE definitions to the
end of files.
o Wrap a few lines > 80 characters.
o Use the same devclass for all ed drivers. This allows machines with
multiple types of cards to have their cards numbered correctly. Before,
you could wind up with two ed0's.
o Protect if_edvar.h from multiple includes because I was there.
require the addition of flag 0x80000 to their config line in
pccard.conf(5). This flag is not optional. These Linksys cards will
not be recognized without it.
Reviewed by: imp, iwasaki
using a cardbus based system with pccbb providing the pcic interface).
Something isn't quite right.. when the driver allocates and activates
its resources, the IO space that was requested reads as all zeros (versus
the original 0xff's as it normally is when there is no device responding).
Also, deactivate the resources before releasing them. OLDCARD doesn't
seem to care but NEWCARD/CARDBUS get rather unhappy if you release
a resource that hasn't been deactivated yet.
Make pcic_p.c only compile with oldcard kernels.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
first. This will fix a few cards that hang on the WD probe. He tells
me that PAO went one step farther and removed the WD proble completely
and none of the cards in the 2.x database broke in PAO3. Since I'm
more conservative in this code, I'm just swapping the order, which he
said also fixed his problem.
Reviewed by: mdodd, iwasaki
Submitted by: sanpai@sanpai.org
too many, so I removed the checks for the valid OUIs. We already do a
checksum of the entire ethernet address, so extra checking against the
OUI shouldn't be needed.
Many ed-based Ethernet PC-cards can't get correct MAC address without
this patch.
Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
Reviewed by: Warner Losh <imp@village.org>
o Expose ed_stop and call it early to shutdown the hardware.
o When releasing the interrupt, pass the cookie for the irq, not
a pointer to the cookie (this is the base problem).
o Release other resources used, just like the ep driver
problem.
o Create new timeout routine so we don't detach the card inside a ISR
but instead drop back to spl0 via a timeout of 0.
o Actually delete the child of the pccard device rather than just faking
it badly.
o Fix sio, ed and ep to have pccard detach routines that are int rather
than void.
o Fix ep and ed pccard detach routines to use if_detach rather than just
if_down. if_detach destroys the device, while if_down just marks it
down. In this incarnation of the pccard things, we map the disable
the slot action to detach the driver, which removes the driver from the
device tree. When that is done, a panic would soon follow as the
ifconfig tried to down the device.
Didn't fix:
o Should cache the pccard dev child's pointer in struct slot
o remove now unused parts of struct slot
o Any driver using softc after detach has been called. sio's softc used
to be statically allocated, so you could check sc->gone, but that is
now gone.
o Didn't remove gone from softc of drivers that use the old pccard method.
Didn't test:
o ed driver changes
o sio driver changes on pccards
o suspend (no laptop or apm support on my desktop)
yet, but that should be resolved shortly. Non memory mapped ed
devices should work, but I cannot test this since my only ed card is
memory mapped.
Submitted by: Matt Dodd <mdodd@freebsd.org>
bootup. Somehow my backout of an abortaive attempt at shared
memory autoconfiguration included this line:
sc->mem_shared = 1;
Which is fairly important as it turns out.
Since I performed my pre-commit testing on a different box with a generic
NE2000 I didn't catch this. Pointy hat.
now lives in the respective bus front end files.
- Add various function prototypes to if_edvar.h
- Clean up some debugging code that snuck into if_ed_isa.c
- Turn on the right bits in files.i386
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
const char *. Originally I was going to add casts from const char * to
char * in some of the pci device drivers, but the reality is that the
pci device probes return constant quoted strings.
