Quartz is a tiny module utilized Freescale VF6xx
system-on-chip and development kit produced by
Device Solutions.
Quartz is available in a form of LGA (38x38x2mm)
or as a module with high-density connectors.
Sponsored by: Device Solutions
the Bufferable bit in the PDE entries of the secondary processor startup
pagetables.
The caches really need to be invalidated even earlier than this, but this
is a big step in the right direction. The invalidate needs to happen
before the MMU is enabled, which means it has to be called from asm code
that's running with physical addressing. Fixing that will be handled in
a future change.
implementations for each of the chips we support. Most chips up through
armv6 can use the armv4 implementation which has a single coprocessor
opcode for this operation. The rather more complex armv7 implementation
comes from netbsd.
While this is technically more correct, I don't think it much matters,
because the only thing in the tree that calls cpu_flush_dcache() is md(4)
and I'm > 99% sure it's bogus that it does so; md has no ability to do
anything that can perturb data cache coherency.
it into a bunch of different .c files. Remove declarations for the unused
mptramp() function from everywhere except AramadaXP (and I think it's
really not used there either, because the code that references it appears
to be insanely does-nothing in nature).
WANDBOARD.common config, but with the freescale-specific optons and devices
all together at the bottom now. In addition to reformatting and shuffling
lines around, two new options are added because they're now known to work,
VFP and FREEBSD_BOOT_LOADER.
This config does not include any static DTB, it requires that u-boot
provide a DTB (or a custom kernel config can compile one in).
This will supercede all the existing WANDBOARD* configs, but those will
be left around for a while to help people transition their customized
configs to include this new one instead.
The temperature monitor device is enabled to sample the die temperature at
16hz. The temperature is published via sysctl. A callout routine at 10hz
monitors the temperature and throttles back the cpu if the temperature
goes over a user-settable throttle point (by default 10C less than the
critical high-point temperature for the chip). The hardware is supposed
to be able to deliver an interrupt when the temperature exceeds a settable
limit, but the interrupt never arrives so for now a callout does the job.
At attach time we read the maximum cpu frequency the chip is allowed to run
at and the cpu is set to run at that speed. It's reported at attach time.
A sysctl variable reports the current speed when queried.
New sysctl values:
dev.imx6_anatop.0.cpu_mhz: 984
dev.imx6_anatop.0.temperature: 37.9C
dev.imx6_anatop.0.throttle_temperature: 95.0C
Steven Lawrance did the initial heavy lifting on this, but I changed
enough stuff that I'm the one to blame if anything breaks.
Submitted by: Steven Lawrance <stl@koffein.net>
and CAMBRIA boards that does not use loader to load the kernel. This
is basically how it was done for i386. This way tunables can also be
set. For example in config file:
env "/conf/AVILA.env"
And in AVILA.env:
vfs.unmapped_buf_allowed=0
MFC after: 2 weeks
is attached, by establishing a temporary mapping of the registers when
necessary. This is a temporary measure to keep progress moving; in the
long run we need better control over the order in which devices attach
(better than "the order they appear in the fdt dts source").
Attempt to demote the superpage if trying to pmap_enter() on
one. Panic only when the particular superpage should
no longer exist for that pmap and address.
Because pmap_enter_locked() is called from few different functions
some redundancy in superpage promotion attempts can be observed.
Hence, avoid promotion in pmap_enter_object() (if the object can
be mapped by superpage it will be handled by pmap_enter_object()
itself) and also do not waste time in pmap_enter_quick().
From now on the promotion will be performed only in pmap_enter().
It was possible to create RW superpage mapping even if
the base pages were RO due to wrong setting of the prot
flag passed to pmap_map_section().
Promotion attempt should be canceled in case of attributes
mismatch between any two base pages. Since we still use
pv_flags to maintain permission to write (PVF_WRITE) and
wired status (PVF_WIRED) for a page, it is also necessary
to take those variables into account.
Invalidate L1 PTE regardles of existance of the corresponding
l2_bucket. This is relevant when superpage is entered via
pmap_enter_object() and will fix crash on entering page
in place of not properly removed superpage.
because we use the 1MiB section maps as they only need a single pagetable.
To allow this we only use pc relative loads to ensure we only load from
physical addresses until we are running from a known virtual address.
As a side effect any data from before or 64MiB after the kernel needs to
be mapped in to be used. This should not be an issue for kernels loaded
with ubldr as it places this data just after the kernel. It will be a
problem when loading directly from anything using the Linux ABI that
places the ATAG data outside this range, for example U-Boot.
Add gpioled(4) to BEAGLEBONE kernel and add the description of the four
on-board leds of beaglebone-black to its DTS file.
Approved by: adrian (mentor, implicit)
change the gpio children can be described as directly connected to the GPIO
controller without the need of describing the OFW GPIO bus itself on the
DTS file.
With this commit the OFW GPIO bus is fully functional on BBB and RPi.
GPIO controllers which want to use the OFW GPIO bus will need similar
changes.
Approved by: adrian (mentor, implicit)
to decide what protections are required by the faulting access. The old
code disassembled the faulting instruction, and there are a lot of new
instructions that aren't handled. The old code is still used for armv4/5
which doesn't have the WNR bit)
routine, now a platform can provide a pointer to an early_putc() routine
which is used instead of cn_putc(). Control can be handed off from early
printf support to standard console support by NULLing out the pointer
during standard console init.
This leverages all the existing error reporting that uses printf calls,
such as panic() which can now be usefully employed even in early
platform init code (useful at least to those who maintain that code and
build kernels with EARLY_PRINTF defined).
Reviewed by: imp, eadler
