divisor. This allows us to set the line speed to the maximum
of 1/4 of the device clock.
o Disable the baudrate generator before programming the line
settings, including baudrate, and enable it afterwards.
was not checked at all. There is only one case when sc_clean_up()
can fail, because of wait_scrn_saver_stop(), but it doesn't hurt
to check anyway.
Reviewed by: rodrigc
Found by: Coverity Prevent
If the embedded controller exists before the sysresource devices, for
example, it will be attached first. Instead, let the normal device
order function work as we first desired. [1]
There still remained a problem where we couldn't allocate resources in
acpi0 that were passed up by the sysresource pseudo-devices. These
devices had to probe/attach first to give their resources to acpi, then
acpi would allocate them before probing/attaching other devices. To
work around this, we attach them from acpi_sysres_alloc(). A better
approach would be to implement multi-pass probe/attach in newbus but
that's a much bigger task.
Suggested by: jhb [1]
Hardware from: Centaur Technologies
MFC after: 1 week
to ensure we match the type signature; we cannot assume HAL_BUS_TAG
and HAL_BUS_HANDLE correspond to bus_space_tag_t and bus_space_handle_t
(should probably do this for HAL_SOFTC too but leave that for now)
MFC after: 1 month
- Fix bfe_encap so that it will pass the address of the mbuf back up to its
caller if/when it modifies it, as it does when doing a m_defrag on a mbuf chain.
- Make sure to unload the dmamap for ALL fragments of a packet, not just the first
- Use BUS_DMA_NOWAIT for all bus_dmamap_load calls so that the allocation of the
map is not delayed - this driver is not set up to handle such delays.
- Reduce the number of RX and TX buffers bfe uses so that it does not use more
bounce buffers than busdma is willing to allow it to use
With these changes, the driver now works properly for a user with a 2GB system,
and it also works on my system when the acceptable address range is lowered to 128MB.
Previously, both of these setups would act up after a few minutes of activity.
from the amr_linux. This simplifies the amr_linux shim and puts the
smarts into amr.c.
I tested this with 2 amr controllers in one box. It seems to work
okay with them.
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
OS dependent layer. Thus, the watchdog timer can go off when the tx
engine is working fine but the OS dependent layer just hasn't been called
to cleanup finished tx transactions. To workaround this, when the watchdog
fires, poke the binary blob to force it to flush any pending tx
completions. If this drops the pending tx count to zero then just return
without logging a message or resetting the chip.
This reportedly fixes the 'device timeout()' errors with at least several
NF4 nve(4) parts.
Submitted by: Nathan Alexander Whitehorn <nathanw@uchicago.edu> (code)
Submitted by: dg (inspiration for comment and explanation)
MFC after: 1 week
POSTWRITE to POSTREAD.
No guarantee that all busdma is usage is perfect, but this change (in
addition to scott's last two commits) makes if_bfe work with > 1GB of
memory in my laptop.
OpenBSD changes. With these changes, PHY part of the driver becomes
functional (it senses media changes and negotiates speed just fine),
previously it just hang with no PHY message, but no data goes through
interface (error message is "can not stop transfer of Tx/Rx descriptor).
Hopefully somebody with more clue/free time will be able to pick up
after me.
Changelog towards if_iwi.c 1.26 (some changes have been committed separately
in the mean time):
- add led support
- add firmware loading on demand
- auto-restart firmware when it crashes
- serialize operations sent to the firmware to reduce firmware crashes
- add power save operation support
- remove incorrect specification of tx power control capability
- add radio on/off switch support
- improve net80211 state machine operation
- recognize and handle beacon miss
- handle authentication and association failures better
- add shared key authentication
- fix ibss mode (many changes)
- fix wme (many changes)
- correct radiotap support (many changes)
- correct bus dma setup of s/g
- correct various locking issues
- fix monitor mode
- fix scanning (many changes)
- recover from wedged scan requests
- respect active channel list
- eliminate cases where interface was marked down on error
- don't treat parity errors as fatal
- reclaim mgt frames immediately from tx queue
- correct interrupt handling, ack early (from NetBSD)
- fix short/long preamble handling
Committed with RELENG_6 compat #if's, should compile in RELENG_6. Requires
net/iwi-firmware-kmod to function.
Much work done by: sam
Tested by: many (freebsd-net), ume, luigi
MFC after: 4 weeks
This driver was generously developed and donated by Highpoint.
It is enabled for i386 only at the moment. I will enable it for amd64
shortly.
Obtained from: HighPoint Technologies, Inc.
- MPSAFE. No more recursive lock required.
- bus_dma(9) conversion. I think it should work on all architectures.
- optimized Rx handler for each normal and jumbo frames. Previously
sk(4) used jumbo frame management code to handle normal sized
frames. As the handler needs an additional lock to protect jumbo
frame management structure from races, it used two lock operations
for each received packet. Now sk(4) uses single lock operation for
normal frame.(Jumbo frame still needs two lock operations as before.)
The hardware supports DMA scatter operations for Rx descriptors such
that it's possible to take advantagee of m_cljget(9) for jumbo frames.
However, due to a unknown reasons it resulted in poor performance on
sparc64. So I dropped m_cljget(9) approach. This should be revisited
since it would reduce one lock operation for jumbo frame handling.
- Tx TCP/Rx IP checksum offload support. According to the data sheet
of SK-NET GENESIS the hardware supports Rx IP/TCP/UDP offload.
But I couldn't make it work on my Yukon hardware. So Rx TCP/UDP was
disabled at the moment. It seems that newer Yukon chips can support
Tx UDP checksum offload too. But I need more documentation first.
- Added more wait time in reading VPD data. It seems that ASUS LOM
takes a very long time to respond VPD read signal.
- Added an additional lock for MII register access callbacks.
- Added more strict received packet validation routine. Previously it
passed corrupted packets to upper layers under certain conditions.
- A new function sk_yukon_tick() to handle auto-negotiation properly.
- Interrupt handler now checks shared interrupt source and protects
the interrupt handler from NULL pointer dereference which was caused
by odd status word value. The status word can returns 0xffffffff if
cable is unplugged while Rx/Tx/auto-negotiation is in progress.
- suspend/resume support(not tested).
- Added Rx/Tx FIFO flush routine for Yukon
- Activate Tx descriptor poll timer in order to protect possible loss
of SK_TXBMU_TX_START command. Previously the driver continuously issued
SK_TXBMU_TX_START when it notices pending Tx descriptors not processed
yet in interrupt handler. That approach would add additional PCI
write access overhead under high Tx load situations and it might fail
if the first SK_TXBMU_TX_START was lost and no interrupt is generated
from the first SK_TXBMU_TX_START command.
- s/printf/if_printf/, s/printf/device_printf/, Axe sk_unit in softc.
- Setting multicast/station address is now safe on strict-alignment
architectures.
- Fix long standing bug in VLAN header length setup.
- Added/corrected register definitions for Yukon.
(Register information from Linux skge driver.)
- Added Rx status definition for Marvell Yukon/XaQti XMAC.
(Rx status register information from Linux skge driver.)
- Update if_oerrors if we encounter watchdog error.
- callout(9) conversion
Special thanks to jkim who let me know RX status differences between
Yukon and XaQti XMAC.
It seems that there is still occasional watchdog timeout error but I
couldn't reproduce it and need more information to analyze it from
users.
Tested by: bz(amd64), me(i386, sparc64), current ML
Frank Behrens frank ! pinky ( sax $ de
Lower the minimum for memory mapped I/O from 32 bytes to 16 bytes.
This fixes bus enumeration on ia64 now that the Diva auxiliary
serial port is attached to.
