Changes since 7.8.0 (from the official changelog):
- Fixed sporadic interrupt generation for associated CQ when processing
a local invalidate work request
- Changes to core scheduling to avoid starving requests from the host
under heavy RDMA Read Request load (e.g. packets to the wire)
- Programmed the tp tx resource limiter in function of the traffic (only
affects iWarp)
- Increased the egress NIC gather list length from 36 to 46 entries
MFC after: 1 week
- Run the adapter's tick at 1Hz and remove link state checks from it.
Instead, have each port check its link state. Delay the check so that
it takes place slightly after the driver is notified of a change in
link state. This is a cheap way to debounce these notifications if
many are received in rapid succession. POLL_LINK_1ST_TIME flag can
also be eliminated as a side effect of these changes.
- Do not reset the PHY when link goes down.
- Clear port's link_fault flag if the PHY indicates link is down.
- get_link_status_r should leave speed and duplex alone when link is down.
MFC after: 1 month
- Only the tunnelq (TXQ_ETH) requires a buf_ring, an ifq, and the watchdog/timer
callouts. Do not allocate these for the other tx queues.
- Use 16k jumbo clusters only on offload capable cards by default.
- Do not allocate a full tx ring for the offload queue if the card is not
offload capable.
- Slightly better freelist size calculation.
- Fix nmbjumbo4 typo, remove unneeded global variables.
MFC after: 3 days
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
- remove mbuf iovec - useful, but adds too much complexity when isolated to
the driver
- remove driver private caching - insufficient benefit over UMA to justify
the added complexity and maintenance overhead
- remove separate logic for managing multiple transmit queues, with the
new drbr routines the control flow can be made to much more closely resemble
legacy drivers
- remove dedicated service threads, with per-cpu callouts one can get the same
benefit much more simply by registering a callout 1 tick in the future if there
are still buffered packets
- remove embedded mbuf usage - Jeffr's changes will (I hope) soon be integrated
greatly reducing the overhead of using kernel APIs for reference counting
clusters
- add hysteresis to descriptor coalescing logic
- add coalesce threshold sysctls to allow users to decide at run-time
between optimizing for forwarding / UDP or optimizing for TCP
- add once per second watchdog to effectively close the very rare races
occurring from coalescing
- incorporate Navdeep's changes to the initialization path required to
convert port and adapter locks back to ordinary mutexes (silencing BPF
LOR complaints)
- enable prefetches in get_packet and tx cleaning
Reviewed by: navdeep@
MFC after: 2 weeks
1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Unify the PHY link detection code.
Obtained from: Navdeep Parhar
MFC after: 10 days
Firmware upgraded to 7.1.0 (from 5.0.0).
T3C EEPROM and SRAM added; Code to update eeprom/sram fixed.
fl_empty and rx_fifo_ovfl counters can be observed via sysctl.
Two new cxgbtool commands to get uP logic analyzer info and uP IOQs
Synced up with Chelsio's "common code" (as of 03/03/09)
Submitted by: Navdeep Parhar at Chelsio
Reviewed by: gnn
MFC after: 2 weeks
packet loss, of between 10-30%. The fix is to put the PHY into
and take it out of local loopback mode when resetting the interface.
Obtained from: Chelsio Inc.
MFC after: 3 days
when it sees only received packets. In some cases where a device only
recieves data it mistakenly thinks that its transmitting side is broken
and resets the device.
Obtained from: Chelsio Inc.
MFC after: 3 days
1) Fix a bug in dealing with the Alerus 1006 PHY which prevented the
device from ever coming back up once it had been set to down.
2) Add a kernel tunable (hw.cxgb.snd_queue_len) which makes it possible
to give the device more than IFQ_MAXLEN entries in its send queue. The
default remains 50.
3) Add code to place the card'd identification and serial number into
its description (%desc) so that users can tell which card they have
installed.
- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- register listeners when an interface is brought up after tom is loaded
- fix setting of multicast filter
- enable link at device attach
- exit tick handler if shutdown is in progress
- add helper for logging TCB
- add sysctls for dumping transmit queues
- note that TOE wxill not be MFC'd until after 7.0 has been finalized
MFC after: 3 days
- return the error from cxgb_tx_common so that when an error is hit we dont
spin forever in the taskq thread
- remove unused rxsd_ref
- simplify header_offset calculation for embedded mbuf headers
- fix memory leak by making sure that mbuf header initialization took place
- disable printf's for stalled queue, don't do offload/ctrl queue restart
when tunnel queue is restarted
- add more diagnostic information about the txq state
- add facility to dump the actual contents of the hardware queue using sysctl
and t3_push_frames).
- Import latest changes to cxgb_main.c and cxgb_sge.c from toestack p4 branch
- make driver local copy of tcp_subr.c and tcp_usrreq.c and override tcp_usrreqs so
TOE can also functions on versions with unmodified TCP
- add cxgb back to the build
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
- remove cpl->iff panic - we can't know the port number from the rspq on the 4-port
- pick the ifnet based on the interface in the CPL header
- switch to using qset 0 for egress on the 4-port for now - may change
when we start using RSS
- move ether_ifdetach to before the port lock gets deinitialized to avoid
hang in the case where there are BPF peers (cxgb_ioctl is called indirectly
when BPF peers are present)
- don't call t3_mac_reset if multiport is set, this was causing tx errors
by misconfiguring the MAC on the 4-port
- change V_TXPKT_INTF to use txpkt_intf as the interfaces are not contiguous
- free the mbuf immediately in the case where the payload is small enough to be copied
into the rspq
- only update the coalesce timer if for a queue if packets were taken off of it
- add in missed 20ms DELAY in initializaton vsc8211
- prompt MFC as this only applies to the 4-port which is currently completely
broken - OK'd by kensmith
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 0 days
- update to firmware version 4.1.0
- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames
Sponsored by: Chelsio
MFC after: 3 days
- upgrade to reflect state of 1.0.0.86
- move from firmware rev 3.2 to 4.0.0
- import driver bits for offload functionality
- remove binary distribution clause from top level files as it
runs counter to the intent of purely supporting the hardware
MFC after: 3 days
(with the notable exception of improvements for using multiple TX queues)
This adds support for the T3B2 ASIC rev
Obtained from: Chelsio
MFC after: 3 days
