This commit really is "fix the OFDM duration calculation to match reality when
running in 802.11g mode."
The AR5212 init vals set AR_MISC_MODE to 0x0 and all the bits that can be set are
set through code.
The AR5416 and later initvals set AR_MISC_MODE to various other values (with
the AR5212 AR_MISC_MODE options cleared), which include AR_PCU_CCK_SIFS_MODE .
This adds 6uS to SIFS on non-CCK frames when transmitting.
This fixes the issue where _DATA_ 802.11g OFDM frames were being TX'ed with
the ACK duration set to 38uS, not 44uS as on the AR5212 (and other devices.)
The AR5212 TX pathway obeys the software-programmed duration field in the packet,
but the 11n TX pathway overrides that with a hardware-calculated duration. This
was getting it wrong because of the above AR_MISC_MODE setting. I've verified
that 11g data OFDM frames are now being TXed with the correct ACK+SIFS duration
programmed in.
Since ath9k does some slightly different bit fiddling when setting up
the TX queues, it may that the TX queue setup/reset functions will need
overriding later on.
segment so that it's always mapped by the loader.
o Change the alternate fault handlers to account for PBVM. Since
currently the region is handled by the VHPT, no alternate faults
will be generated for it.
been undergoing test for some weeks. This improves the RX
mbuf handling to avoid system hang due to depletion. Thanks
to all those who have been testing the code, and to Beezar
Liu for the design changes.
Next the igb driver is updated for similar RX changes, but
also to add new features support for our upcoming i350 family
of adapters.
MFC after a week
chipsets that do not have an HT slave at 0:0:0:0. The Linux quirk is
actually specific to Nvidia chipsets and the check I had added was in
the wrong place.
Prodded by: nathanw
- Always enable the HyperTransport MSI mapping window for HyperTransport
to PCI bridges (these show up as HyperTransport slave devices).
The mapping windows in PCI-PCI bridges are enabled by existing code
in the PCI-PCI bridge driver as MSI requests propagate up the device
tree, but Host-PCI bridges don't really show up in that tree.
- If the PCI device at domain 0 bus 0 slot 0 function 0 is not a
HyperTransport device, then blacklist MSI on any other HT devices in
the system. Linux has a similar quirk.
PR: kern/155442
Tested by: Zack Dannar zdannar of gmail
MFC after: 1 week
which are not yet fully initialized (i.e. ones with p_state == PRS_NEW).
Without it, we could panic in _thread_lock_flags().
Note that there may be other instances of FOREACH_PROC_IN_SYSTEM() that
require similar fix.
Reported by: pho, keramida
Discussed with: kib
ffs_snapgone(). ufs.ko module is not build with FFS define, causing
snapshot inode number slots in superblock never be freed, as well as a
reference on the snapshot vnode.
IFS was removed several years ago, and UFS/FFS separation was not
maintained for real.
Reported, analyzed and tested by: Yamagi Burmeister <lists yamagi org>
MFC after: 3 days
With this change, driver may not notice updated descriptor status
change when bounce buffers are active. However, rxeof() in next run
will handle the synchronization.
Change dc_rxeof() a bit to return the number of processed frames in
RX descriptor ring. Previously it returned the number of frames
that were successfully passed to upper stack which in turn means it
ignored frames that were discarded due to errors. The number of
processed frames in RX descriptor ring is used to detect whether
driver is out of sync with controller's current descriptor pointer.
Returning number of processed frames reduces unnecessary (probably
wrong) re-synchronization.
Reviewed by: marius
Unfortunately, it pulls in <machine/cputypes.h> but it is small enough and
namespace pollution is minimal, I hope.
Pointed out by: bde
Pointy hat: jkim
Add support for Pre-Boot Virtual Memory (PBVM) to the loader.
PBVM allows us to link the kernel at a fixed virtual address without
having to make any assumptions about the physical memory layout. On
the SGI Altix 350 for example, there's no usuable physical memory
below 192GB. Also, the PBVM allows us to control better where we're
going to physically load the kernel and its modules so that we can
make sure we load the kernel in memory that's close to the BSP.
The PBVM is managed by a simple page table. The minimum size of the
page table is 4KB (EFI page size) and the maximum is currently set
to 1MB. A page in the PBVM is 64KB, as that's the maximum alignment
one can specify in a linker script. The bottom line is that PBVM is
between 64KB and 8GB in size.
The loader maps the PBVM page table at a fixed virtual address and
using a single translations. The PBVM itself is also mapped using a
single translation for a maximum of 32MB.
While here, increase the heap in the EFI loader from 512KB to 2MB
and set the stage for supporting relocatable modules.
The compiler will truncate the 32-bit return value of mv_gpio_value_get()
to match the 8-bit return value of mv_gpio_in(). A conditional expression
is used to have mv_gpio_in() always return 0 or 1 instead.
soon as possible for stack protector. However, dummy timecounter does not
have enough entropy and we don't need to sacrifice Pentium class and later.
Pointed out by: Maxim Dounin (mdounin at mdounin dot ru)
The compiler seems to assume it's a 32-bit integral and rounding to the
page size using the standard expression (((u_long)(x) + mask) & ~mask),
results in a 32-bit value. Dropping the 'U' suffix is enough to have the
compiler treat the expression as a 64-bit integral.
handlers.
o Put the IVT in its own section and keep the supporting code close.
o Make sure the VHPT is sized so that it can be mapped using a single
translation.
o Map the PAL code and VHPT with a translation that has the right size.
Assume the platform has a PAL code size that can be mapped with a
single translations.
o Pass the pointer to the bootinfo structure as an argument to ia64_init().
o Get rid of LOG2_ID_PAGE_SIZE and IA64_ID_PAGE_SIZE. It was used to map
the regions 6 & 7 and was as large as possible. The problem is that we
can't support memory attributes easily if the granuratity is not a page.
We need to support memory attributes because the new USB stack violates
the BUS_DMA(9) interface.
o Update some comments...
NOTE: this is broken for SMP kernels, because the AP startup code hasn't
been updated yet.
can be put right at the front when put in its own section. This makes
sure that when the loader can only map a relatively small part of the
PBVM, the IVT and the startup code is wired.
