in getting mirror-2.3 to work with FreeBSD, i found that timelocal.pl has
a bug. a patch is included below. this needs to be applied to both
src/gnu/usr.bin/perl/lib/timelocal.pl and
src/usr.sbin/xntpd/scripts/monitoring/timelocal.pl
Reviewed by:
Submitted by:
Obtained from:
in getting mirror-2.3 to work with FreeBSD, i found that timelocal.pl has
a bug. a patch is included below. this needs to be applied to both
src/gnu/usr.bin/perl/lib/timelocal.pl and
src/usr.sbin/xntpd/scripts/monitoring/timelocal.pl
Submitted by: jmb
/*
* filename [ standard | optional ] [ config-dependent ]
* [ dev* | profiling-routine ] [ device-driver] [ no-obj ]
* [ compile-with "compile rule" [no-implicit-rule] ]
* [ dependancy "dependancy-list"]
*/
I added
no-obj - This entry does not create anything linkable to the kernel.
dependancy - Add additional dependancy rules to a target.
no-implicit-rule - Don't assume .c -> .o type rules. Config is really
dumb in this area and assumes that everything is a .c file
irregarless of extention. This was the best choice really
since there may even be .c file that you don't want to follow
the standard rules.
This was all done so that the building to the aic7770 assembler and using
the aic7770 assembler in the building of the aic7770 driver could be config
dependant. I can now have an entry like this for the driver:
aic7770 optional ahc device-driver \
compile-with "${CC} $> -o $@" \
dependancy "$S/gnu/misc/aic7770/aic7770.c" \
no-obj no-implicit-rule
aic7770_seq.h optional ahc device-driver \
compile-with "${.CURDIR}/aic7770 -o $@ $S/gnu/misc/aic7770/aic7770.seq"\
dependancy "$S/gnu/misc/aic7770/aic7770.seq aic7770" \
no-obj no-implicit-rule
i386/isa/aic7770.c optional ahc device-driver \
dependancy "aic7770_seq.h"
I also added '\' escaping to newlines so that this doesn't look as gross as
it could have.
Reviewed by: jkh
of config so YOU MUST RECOMPILE CONFIG. Modifying config was the cleanest
solution to integrating this driver into the tree which will become more
obvious in the next commit.
a discussion going on about removing this code from the burden of the
GPL, but it won't happen before Beta, and this code should be tested
before release.
Supports 27/2842 class adaptec cards and is almost capable of supporting
aic7870 based adapters (294X series cards). It does not support Wide
controllers or the second channel on Twin boards although I have work in
progress on getting both channels and running.
I have also added a few performance improvements to this version that give
us approximately a 25% boost over the original driver. These patches have
been submitted to the author.
Obtained from: Linux aic7770 driver (John Aycock - aycock@cpsc.ucalgary.ca)
that Poul builds the rest of the dists properly. I'll run this over the
XFree86 dist, but the rest will be up to him. Check bindist rule for
the single line to add - it's trivial.
2. See if swapon() failed and at least print a diagnostic.
3. Use -1 instead of strheight()/strwidth() everywhere.
Reviewed by:
Submitted by:
Obtained from:
Smack the netboot program around so that it will allow the user to
specify mount options. [So that you can boot from a privileged port]
Change the default boot image name in netboot to /kernel, then strip
the leading slash when actually going out to get the NFS file handle.
Added support for 3Com 3c503 cards. Also added another command to
the (trans) that allows you to switch the 3Com's on-board transceiver
on and off. (ether.c, ether.h, bootmenu.c)
Modified the Makefile to support new compile-time options for 3c503
cards:
-DINCLUDE_3COM Include support for 3c503
-D_3COM_BASE=0x300 Define 3c503 base i/o address (if not
specified, 0x300 is the default)
-D_3COM_USE_AUI Disable the 3c503's transceiver by
default (without this flag the transceiver
is on by default)
and it doesn't support --unlink. I think it's time to nuke cpio completely
out of the installation process, unless someone can think of a really good
reason to keep it (and don't say multiple volume extraction since we a) don't
use it anywhere anyway, and b) tar supports that too, now).
for Wine support. The current snapshot of wine works fine with this.
This should go into the beta as the code which it calls in the kernel is
already there, and works fine.
Further investigation showed that prefix was erroneously set to /usr/local
for X11 based ports as well, when the assumption was that they'd really go
into ${X11BASE} (an /etc/make.conf variable that the user's free to set).
Set X11BASE to /usr/X11R6 if the user hasn't already, and assume that
the user really wants prefix to point there when the port is XMKMF based.
