e706f7f0c7
- Simplify the amount of work that has be done for each architecture by pushing more of the truly MI code down into the PCI bus driver. - Don't bind MSI-X indicies to IRQs so that we can allow a driver to map multiple MSI-X messages into a single IRQ when handling a message shortage. The changes include: - Add a new pcib_if method: PCIB_MAP_MSI() which is called by the PCI bus to calculate the address and data values for a given MSI/MSI-X IRQ. The x86 nexus drivers map this into a call to a new 'msi_map()' function in msi.c that does the mapping. - Retire the pcib_if method PCIB_REMAP_MSIX() and remove the 'index' parameter from PCIB_ALLOC_MSIX(). MD code no longer has any knowledge of the MSI-X index for a given MSI-X IRQ. - The PCI bus driver now stores more MSI-X state in a child's ivars. Specifically, it now stores an array of IRQs (called "message vectors" in the code) that have associated address and data values, and a small virtual version of the MSI-X table that specifies the message vector that a given MSI-X table entry uses. Sparse mappings are permitted in the virtual table. - The PCI bus driver now configures the MSI and MSI-X address/data registers directly via custom bus_setup_intr() and bus_teardown_intr() methods. pci_setup_intr() invokes PCIB_MAP_MSI() to determine the address and data values for a given message as needed. The MD code no longer has to call back down into the PCI bus code to set these values from the nexus' bus_setup_intr() handler. - The PCI bus code provides a callout (pci_remap_msi_irq()) that the MD code can call to force the PCI bus to re-invoke PCIB_MAP_MSI() to get new values of the address and data fields for a given IRQ. The x86 MSI code uses this when an MSI IRQ is moved to a different CPU, requiring a new value of the 'address' field. - The x86 MSI psuedo-driver loses a lot of code, and in fact the separate MSI/MSI-X pseudo-PICs are collapsed down into a single MSI PIC driver since the only remaining diff between the two is a substring in a bootverbose printf. - The PCI bus driver will now restore MSI-X state (including programming entries in the MSI-X table) on device resume. - The interface for pci_remap_msix() has changed. Instead of accepting indices for the allocated vectors, it accepts a mini-virtual table (with a new length parameter). This table is an array of u_ints, where each value specifies which allocated message vector to use for the corresponding MSI-X message. A vector of 0 forces a message to not have an associated IRQ. The device may choose to only use some of the IRQs assigned, in which case the unused IRQs must be at the "end" and will be released back to the system. This allows a driver to use the same remap table for different shortage values. For example, if a driver wants 4 messages, it can use the same remap table (which only uses the first two messages) for the cases when it only gets 2 or 3 messages and in the latter case the PCI bus will release the 3rd IRQ back to the system. MFC after: 1 month
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html