d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
7e2437190c
freebsd-skq/sys/dev/ata/ata-disk.c

959 lines
29 KiB
C
Raw Normal View History

Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/*-
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
* Copyright (c) 1998,1999,2000,2001,2002 S<EFBFBD>ren Schmidt <sos@FreeBSD.org>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
$Id$ -> $FreeBSD$
1999-08-28 01:08:13 +00:00
* $FreeBSD$
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
*/
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
#include "opt_ata.h"
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/param.h>
#include <sys/systm.h>
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
#include <sys/ata.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/kernel.h>
#include <sys/malloc.h>
Separate the struct bio related stuff out of <sys/buf.h> into <sys/bio.h>. <sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall not be made a nested include according to bdes teachings on the subject of nested includes. Diskdrivers and similar stuff below specfs::strategy() should no longer need to include <sys/buf.> unless they need caching of data. Still a few bogus uses of struct buf to track down. Repocopy by: peter
2000-05-05 09:59:14 +00:00
#include <sys/bio.h>
Have another go at the VIA support, this time use the PCI ID form the main component in the southbridge chip to determine which VIA chip we are dealing with. Try to enable DMA on generic controllers that say they has the capability, instead of relying on the BIOS to have set it up.
1999-12-14 10:25:28 +00:00
#include <sys/bus.h>
nullclose, not noclose of course.
1999-09-05 15:41:09 +00:00
#include <sys/conf.h>
Use micro "disk" layer in ata-disk Reviewed by: sos
1999-09-03 10:57:17 +00:00
#include <sys/disk.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/devicestat.h>
call ata_reinit in addump trying to make sure the dump will succed, also check for errors underways, and make it possible to abort the dump by hitting a key.
1999-11-27 17:06:10 +00:00
#include <sys/cons.h>
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
#include <sys/sysctl.h>
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
#include <vm/vm.h>
#include <vm/pmap.h>
#include <machine/md_var.h>
* Completely rewrite the alpha busspace to hide the implementation from the drivers. * Remove legacy inx/outx support from chipset and replace with macros which call busspace. * Rework pci config accesses to route through the pcib device instead of calling a MD function directly. With these changes it is possible to cleanly support machines which have more than one independantly numbered PCI busses. As a bonus, the new busspace implementation should be measurably faster than the old one.
2000-08-28 21:48:13 +00:00
#include <machine/bus.h>
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
#include <sys/rman.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <dev/ata/ata-all.h>
#include <dev/ata/ata-disk.h>
Add support for ATA "pseudo" RAID controllers as the Promise Fasttrak and HighPoint HPT370 controllers. Use by defining the RAID in the BIOS and the "ar driver will pick it up automagically...
2000-10-13 13:04:45 +00:00
#include <dev/ata/ata-raid.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
/* device structures */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static d_open_t adopen;
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
static d_close_t adclose;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static d_strategy_t adstrategy;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
static d_dump_t addump;
This commit should be a extensive NO-OP: Reformat and initialize correctly all "struct cdevsw". Initialize the d_maj and d_bmaj fields. The d_reset field was not removed, although it is never used. I used a program to do most of this, so all the files now use the same consistent format. Please keep it that way. Vinum and i4b not modified, patches emailed to respective authors.
1999-05-30 16:53:49 +00:00
static struct cdevsw ad_cdevsw = {
/* open */ adopen,
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
/* close */ adclose,
This commit should be a extensive NO-OP: Reformat and initialize correctly all "struct cdevsw". Initialize the d_maj and d_bmaj fields. The d_reset field was not removed, although it is never used. I used a program to do most of this, so all the files now use the same consistent format. Please keep it that way. Vinum and i4b not modified, patches emailed to respective authors.
1999-05-30 16:53:49 +00:00
/* read */ physread,
/* write */ physwrite,
Use micro "disk" layer in ata-disk Reviewed by: sos
1999-09-03 10:57:17 +00:00
/* ioctl */ noioctl,
This commit should be a extensive NO-OP: Reformat and initialize correctly all "struct cdevsw". Initialize the d_maj and d_bmaj fields. The d_reset field was not removed, although it is never used. I used a program to do most of this, so all the files now use the same consistent format. Please keep it that way. Vinum and i4b not modified, patches emailed to respective authors.
1999-05-30 16:53:49 +00:00
/* poll */ nopoll,
/* mmap */ nommap,
/* strategy */ adstrategy,
slight change in the way we hi-jack the wd drivers cdevsw.
1999-07-17 17:55:53 +00:00
/* name */ "ad",
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
/* maj */ 116,
/* dump */ addump,
Use micro "disk" layer in ata-disk Reviewed by: sos
1999-09-03 10:57:17 +00:00
/* psize */ nopsize,
This commit should be a extensive NO-OP: Reformat and initialize correctly all "struct cdevsw". Initialize the d_maj and d_bmaj fields. The d_reset field was not removed, although it is never used. I used a program to do most of this, so all the files now use the same consistent format. Please keep it that way. Vinum and i4b not modified, patches emailed to respective authors.
1999-05-30 16:53:49 +00:00
/* flags */ D_DISK,
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
};
Bite the bullet and allocate the devsw entry at compile time.
1999-09-12 20:40:29 +00:00
static struct cdevsw addisk_cdevsw;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* prototypes */
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static void ad_invalidatequeue(struct ad_softc *, struct ad_request *);
static int ad_tagsupported(struct ad_softc *);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
static void ad_timeout(struct ad_request *);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static void ad_free(struct ad_request *);
static int ad_version(u_int16_t);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
/* misc defines */
#define AD_MAX_RETRIES 3
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
/* internal vars */
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
static u_int32_t adp_lun_map = 0;
Make the TUNABLE_*() macros look and behave more consistantly like the SYSCTL_*() macros. TUNABLE_INT_DECL() was an odd name because it didn't actually declare the int, which is what the name suggests it would do.
2001-06-06 22:17:08 +00:00
static int ata_dma = 1;
Misc little cleanups: Link if only ATAPI device in kernel config Remove unused #includes Rearrange a bit in ata-raid to make diff against -stable smaller Enable wc as default again, dunne how this happend...
2002-03-05 09:24:19 +00:00
static int ata_wc = 1;
Make the TUNABLE_*() macros look and behave more consistantly like the SYSCTL_*() macros. TUNABLE_INT_DECL() was an odd name because it didn't actually declare the int, which is what the name suggests it would do.
2001-06-06 22:17:08 +00:00
static int ata_tags = 0;
"Fix" the previous initial attempt at fixing TUNABLE_INT(). This time around, use a common function for looking up and extracting the tunables from the kernel environment. This saves duplicating the same function over and over again. This way typically has an overhead of 8 bytes + the path string, versus about 26 bytes + the path string.
2001-06-08 05:24:21 +00:00
TUNABLE_INT("hw.ata.ata_dma", &ata_dma);
TUNABLE_INT("hw.ata.wc", &ata_wc);
TUNABLE_INT("hw.ata.tags", &ata_tags);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
static MALLOC_DEFINE(M_AD, "AD driver", "ATA disk driver");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
/* sysctl vars */
SYSCTL_DECL(_hw_ata);
SYSCTL_INT(_hw_ata, OID_AUTO, ata_dma, CTLFLAG_RD, &ata_dma, 0,
"ATA disk DMA mode control");
Correct the sysctl names to match the tuneables. Proberly flush the tag queue on detach.
2001-04-05 11:13:07 +00:00
SYSCTL_INT(_hw_ata, OID_AUTO, wc, CTLFLAG_RD, &ata_wc, 0,
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
"ATA disk write caching");
Correct the sysctl names to match the tuneables. Proberly flush the tag queue on detach.
2001-04-05 11:13:07 +00:00
SYSCTL_INT(_hw_ata, OID_AUTO, tags, CTLFLAG_RD, &ata_tags, 0,
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
"ATA disk tagged queuing support");
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
void
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ad_attach(struct ata_device *atadev)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
struct ad_softc *adp;
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
dev_t dev;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Use M_ZERO flag on malloc when approbiate.
2000-12-26 12:05:49 +00:00
if (!(adp = malloc(sizeof(struct ad_softc), M_AD, M_NOWAIT | M_ZERO))) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(atadev, "failed to allocate driver storage\n");
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
return;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device = atadev;
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
#ifdef ATA_STATIC_ID
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->lun = (device_get_unit(atadev->channel->dev)<<1)+ATA_DEV(atadev->unit);
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
#else
adp->lun = ata_get_lun(&adp_lun_map);
#endif
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_set_name(atadev, "ad", adp->lun);
adp->heads = atadev->param->heads;
adp->sectors = atadev->param->sectors;
adp->total_secs = atadev->param->cylinders * adp->heads * adp->sectors;
Add new support for locking an ATA channel and use that throughout the ATA/ATAPI driver. This solves the concurrency problem with the new GEOM code, and also cuts a good deal of the patch size in the upcoming MFC.
2002-03-11 21:04:32 +00:00
bioq_init(&adp->queue);
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
/* does this device need oldstyle CHS addressing */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (!ad_version(atadev->param->version_major) ||
!(atadev->param->atavalid & ATA_FLAG_54_58) || !atadev->param->lba_size)
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
adp->flags |= AD_F_CHS_USED;
/* use the 28bit LBA size if valid */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (atadev->param->cylinders == 16383 &&
adp->total_secs < atadev->param->lba_size)
adp->total_secs = atadev->param->lba_size;
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
/* use the 48bit LBA size if valid */
Fix the problem that some (in my book broken) disks reports to be able to use 48bit addressing mode, but says the 48bit size of the disk is 0, which according to spec means it can address zero sectors in 48bit mode, why then say it supports 48bit mode at all..
2002-02-18 11:52:51 +00:00
if (atadev->param->support.address48 &&
atadev->param->lba_size48 > 268435455)
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->total_secs = atadev->param->lba_size48;
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
Add new support for locking an ATA channel and use that throughout the ATA/ATAPI driver. This solves the concurrency problem with the new GEOM code, and also cuts a good deal of the patch size in the upcoming MFC.
2002-03-11 21:04:32 +00:00
ATA_SLEEPLOCK_CH(atadev->channel, ATA_CONTROL);
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
/* use multiple sectors/interrupt if device supports it */
adp->transfersize = DEV_BSIZE;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ad_version(atadev->param->version_major)) {
int secsperint = max(1, min(atadev->param->sectors_intr, 16));
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (!ata_command(atadev, ATA_C_SET_MULTI, 0, secsperint,
0, ATA_WAIT_INTR) && !ata_wait(atadev, 0))
adp->transfersize *= secsperint;
Be a bit more restrictive in using multisector transfers.
2000-08-06 18:01:47 +00:00
}
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
/* enable read caching if not default on device */
if (ata_command(atadev, ATA_C_SETFEATURES,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
0, 0, ATA_C_F_ENAB_RCACHE, ATA_WAIT_INTR))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(atadev, "enabling readahead cache failed\n");
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
/* enable write caching if allowed and not default on device */
Don't enable write cacheing on devices that don't support tagged queuing unless hw.ata.wc is set. Approved by: sos MFC after: 1 week
2001-10-24 18:24:09 +00:00
if (ata_wc || (ata_tags && ad_tagsupported(adp))) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(atadev, ATA_C_SETFEATURES,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
0, 0, ATA_C_F_ENAB_WCACHE, ATA_WAIT_INTR))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(atadev, "enabling write cache failed\n");
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
}
else {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(atadev, ATA_C_SETFEATURES,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
0, 0, ATA_C_F_DIS_WCACHE, ATA_WAIT_INTR))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(atadev, "disabling write cache failed\n");
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
}
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
/* use DMA if allowed and if drive/controller supports it */
if (ata_dma)
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_dmainit(atadev->channel, atadev->unit, ata_pmode(atadev->param),
ata_wmode(atadev->param), ata_umode(atadev->param));
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
else
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_dmainit(atadev->channel, atadev->unit,
ata_pmode(atadev->param), -1, -1);
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
/* use tagged queueing if allowed and supported */
if (ata_tags && ad_tagsupported(adp)) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->num_tags = atadev->param->queuelen;
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
adp->flags |= AD_F_TAG_ENABLED;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->flags |= ATA_QUEUED;
if (ata_command(atadev, ATA_C_SETFEATURES,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
0, 0, ATA_C_F_DIS_RELIRQ, ATA_WAIT_INTR))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(atadev, "disabling release interrupt failed\n");
if (ata_command(atadev, ATA_C_SETFEATURES,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
0, 0, ATA_C_F_DIS_SRVIRQ, ATA_WAIT_INTR))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(atadev, "disabling service interrupt failed\n");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
Rearrange the probecode, so that 80pin cables can be identified correctly on both master and slave. Smash together the ata_params & atapi_params structures as they are more or less equal anyways. Get rid of the last SYSINIT's in here.
2000-01-18 21:02:59 +00:00
Add new support for locking an ATA channel and use that throughout the ATA/ATAPI driver. This solves the concurrency problem with the new GEOM code, and also cuts a good deal of the patch size in the upcoming MFC.
2002-03-11 21:04:32 +00:00
ATA_UNLOCK_CH(atadev->channel);
Add support for ATA "pseudo" RAID controllers as the Promise Fasttrak and HighPoint HPT370 controllers. Use by defining the RAID in the BIOS and the "ar driver will pick it up automagically...
2000-10-13 13:04:45 +00:00
devstat_add_entry(&adp->stats, "ad", adp->lun, DEV_BSIZE,
DEVSTAT_NO_ORDERED_TAGS,
DEVSTAT_TYPE_DIRECT | DEVSTAT_TYPE_IF_IDE,
DEVSTAT_PRIORITY_DISK);
dev = disk_create(adp->lun, &adp->disk, 0, &ad_cdevsw, &addisk_cdevsw);
dev->si_drv1 = adp;
dev->si_iosize_max = 256 * DEV_BSIZE;
adp->dev = dev;
Move the disklabel construction to the attach function instead of in open. This prevent panics when a the disklabel is accessed on an ATA-RAID subdisk.
2001-04-27 19:47:33 +00:00
/* construct the disklabel */
bzero(&adp->disk.d_label, sizeof(struct disklabel));
adp->disk.d_label.d_secsize = DEV_BSIZE;
adp->disk.d_label.d_nsectors = adp->sectors;
adp->disk.d_label.d_ntracks = adp->heads;
adp->disk.d_label.d_ncylinders = adp->total_secs/(adp->heads*adp->sectors);
adp->disk.d_label.d_secpercyl = adp->sectors * adp->heads;
adp->disk.d_label.d_secperunit = adp->total_secs;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
atadev->driver = adp;
Major update of the ATA RAID code, part 2: More cleanups of the RAID1 failure mode code. Add functionality that writes the changed RAID config setup back to the disks (in controller BIOS specific format), so that a reboot will make the BIOS pick up the changed config.
2002-02-12 11:35:15 +00:00
atadev->flags = 0;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
/* if this disk belongs to an ATA RAID dont print the probe */
Major update of the ATA RAID code, part 3: Add code to properly detach/attach disks that are part of a RAID. Mark a disk that is attached on an ATA channel belonging to a RAID as a spare disk that can be used for rebuilding failed RAID1's. Add support for rebuilding failed RAID1's. Several fixes to the detach/attach code. For replacing a disk in a failed RAID1 do the following: Find the controller channel# of the failed disk. Exec 'atacontrol detach <channel#>' to free the disk from the system. Replace the failed disk with a new one of at least the same size. If your have your disks in drawers/enclosures this can be done with the system still running. Exec 'atacontrol attach <channel#>' to add the disk to the system and mark it as a valid spare for rebuild. Exec 'atacontrol rebuild <array#>' The system will rebuild the array on the fly, the array can still be used during this, although with slower performance. Please let me know of any problems with this! Sponsored by: Advanis Inc. MFC after: 2 weeks
2002-03-03 15:36:21 +00:00
if (ata_raiddisk_attach(adp))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->flags |= AD_F_RAID_SUBDISK;
else
Major update of the ATA RAID code, part 3: Add code to properly detach/attach disks that are part of a RAID. Mark a disk that is attached on an ATA channel belonging to a RAID as a spare disk that can be used for rebuilding failed RAID1's. Add support for rebuilding failed RAID1's. Several fixes to the detach/attach code. For replacing a disk in a failed RAID1 do the following: Find the controller channel# of the failed disk. Exec 'atacontrol detach <channel#>' to free the disk from the system. Replace the failed disk with a new one of at least the same size. If your have your disks in drawers/enclosures this can be done with the system still running. Exec 'atacontrol attach <channel#>' to add the disk to the system and mark it as a valid spare for rebuild. Exec 'atacontrol rebuild <array#>' The system will rebuild the array on the fly, the array can still be used during this, although with slower performance. Please let me know of any problems with this! Sponsored by: Advanis Inc. MFC after: 2 weeks
2002-03-03 15:36:21 +00:00
ad_print(adp);
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
}
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
void
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ad_detach(struct ata_device *atadev, int flush) /* get rid of flush XXX SOS */
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
{
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
struct ad_softc *adp = atadev->driver;
Refine the detach/attach code. Proberly fail outstanding bio requests on devices that are detached. This makes it possible to change between disk/cdrom/dvd/whathaveyou in a notebook, just by suspending it, changing the device in the bay (or what you model calls it), unsuspend and the ATA driver will figure out what disappeared and properly fail those, and attach any new devices found.
2001-03-14 12:05:44 +00:00
struct ad_request *request;
struct bio *bp;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
atadev->flags |= ATA_D_DETACHING;
ata_prtdev(atadev, "removed from configuration\n");
Correct the sysctl names to match the tuneables. Proberly flush the tag queue on detach.
2001-04-05 11:13:07 +00:00
ad_invalidatequeue(adp, NULL);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
TAILQ_FOREACH(request, &atadev->channel->ata_queue, chain) {
if (request->softc != adp)
Refine the detach/attach code. Proberly fail outstanding bio requests on devices that are detached. This makes it possible to change between disk/cdrom/dvd/whathaveyou in a notebook, just by suspending it, changing the device in the bay (or what you model calls it), unsuspend and the ATA driver will figure out what disappeared and properly fail those, and attach any new devices found.
2001-03-14 12:05:44 +00:00
continue;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
TAILQ_REMOVE(&atadev->channel->ata_queue, request, chain);
Actually biofinish(struct bio *, struct devstat *, int error) is more general than the bioerror(). Most of this patch is generated by scripts.
2001-05-06 20:00:03 +00:00
biofinish(request->bp, NULL, ENXIO);
Refine the detach/attach code. Proberly fail outstanding bio requests on devices that are detached. This makes it possible to change between disk/cdrom/dvd/whathaveyou in a notebook, just by suspending it, changing the device in the bay (or what you model calls it), unsuspend and the ATA driver will figure out what disappeared and properly fail those, and attach any new devices found.
2001-03-14 12:05:44 +00:00
ad_free(request);
}
while ((bp = bioq_first(&adp->queue))) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
bioq_remove(&adp->queue, bp);
Actually biofinish(struct bio *, struct devstat *, int error) is more general than the bioerror(). Most of this patch is generated by scripts.
2001-05-06 20:00:03 +00:00
biofinish(bp, NULL, ENXIO);
Refine the detach/attach code. Proberly fail outstanding bio requests on devices that are detached. This makes it possible to change between disk/cdrom/dvd/whathaveyou in a notebook, just by suspending it, changing the device in the bay (or what you model calls it), unsuspend and the ATA driver will figure out what disappeared and properly fail those, and attach any new devices found.
2001-03-14 12:05:44 +00:00
}
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
disk_invalidate(&adp->disk);
Add support for ATA "pseudo" RAID controllers as the Promise Fasttrak and HighPoint HPT370 controllers. Use by defining the RAID in the BIOS and the "ar driver will pick it up automagically...
2000-10-13 13:04:45 +00:00
disk_destroy(adp->dev);
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
devstat_remove_entry(&adp->stats);
Minor cleanup to the previous commit: Print what devices went away and which arrived. Avoid timeout loop on missing status.
2001-03-14 14:00:09 +00:00
if (flush) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(atadev, ATA_C_FLUSHCACHE, 0, 0, 0, ATA_WAIT_READY))
ata_prtdev(atadev, "flushing cache on detach failed\n");
Minor cleanup to the previous commit: Print what devices went away and which arrived. Avoid timeout loop on missing status.
2001-03-14 14:00:09 +00:00
}
Major update of the ATA RAID code, part 3: Add code to properly detach/attach disks that are part of a RAID. Mark a disk that is attached on an ATA channel belonging to a RAID as a spare disk that can be used for rebuilding failed RAID1's. Add support for rebuilding failed RAID1's. Several fixes to the detach/attach code. For replacing a disk in a failed RAID1 do the following: Find the controller channel# of the failed disk. Exec 'atacontrol detach <channel#>' to free the disk from the system. Replace the failed disk with a new one of at least the same size. If your have your disks in drawers/enclosures this can be done with the system still running. Exec 'atacontrol attach <channel#>' to add the disk to the system and mark it as a valid spare for rebuild. Exec 'atacontrol rebuild <array#>' The system will rebuild the array on the fly, the array can still be used during this, although with slower performance. Please let me know of any problems with this! Sponsored by: Advanis Inc. MFC after: 2 weeks
2002-03-03 15:36:21 +00:00
if (adp->flags & AD_F_RAID_SUBDISK)
ata_raiddisk_detach(adp);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_free_name(atadev);
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
ata_free_lun(&adp_lun_map, adp->lun);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
atadev->driver = NULL;
Major update of the ATA RAID code, part 2: More cleanups of the RAID1 failure mode code. Add functionality that writes the changed RAID config setup back to the disks (in controller BIOS specific format), so that a reboot will make the BIOS pick up the changed config.
2002-02-12 11:35:15 +00:00
atadev->flags = 0;
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
free(adp, M_AD);
}
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
static int
KSE Milestone 2 Note ALL MODULES MUST BE RECOMPILED make the kernel aware that there are smaller units of scheduling than the process. (but only allow one thread per process at this time). This is functionally equivalent to teh previousl -current except that there is a thread associated with each process. Sorry john! (your next MFC will be a doosie!) Reviewed by: peter@freebsd.org, dillon@freebsd.org X-MFC after: ha ha ha ha
2001-09-12 08:38:13 +00:00
adopen(dev_t dev, int flags, int fmt, struct thread *td)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ad_softc *adp = dev->si_drv1;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
if (adp->flags & AD_F_RAID_SUBDISK)
return EBUSY;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
return 0;
}
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
static int
KSE Milestone 2 Note ALL MODULES MUST BE RECOMPILED make the kernel aware that there are smaller units of scheduling than the process. (but only allow one thread per process at this time). This is functionally equivalent to teh previousl -current except that there is a thread associated with each process. Sorry john! (your next MFC will be a doosie!) Reviewed by: peter@freebsd.org, dillon@freebsd.org X-MFC after: ha ha ha ha
2001-09-12 08:38:13 +00:00
adclose(dev_t dev, int flags, int fmt, struct thread *td)
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
{
struct ad_softc *adp = dev->si_drv1;
Add new support for locking an ATA channel and use that throughout the ATA/ATAPI driver. This solves the concurrency problem with the new GEOM code, and also cuts a good deal of the patch size in the upcoming MFC.
2002-03-11 21:04:32 +00:00
ATA_SLEEPLOCK_CH(adp->device->channel, ATA_CONTROL);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(adp->device, ATA_C_FLUSHCACHE, 0, 0, 0, ATA_WAIT_READY))
ata_prtdev(adp->device, "flushing cache on close failed\n");
Add new support for locking an ATA channel and use that throughout the ATA/ATAPI driver. This solves the concurrency problem with the new GEOM code, and also cuts a good deal of the patch size in the upcoming MFC.
2002-03-11 21:04:32 +00:00
ATA_UNLOCK_CH(adp->device->channel);
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
return 0;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static void
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
adstrategy(struct bio *bp)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
struct ad_softc *adp = bp->bio_dev->si_drv1;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int s;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->flags & ATA_D_DETACHING) {
Actually biofinish(struct bio *, struct devstat *, int error) is more general than the bioerror(). Most of this patch is generated by scripts.
2001-05-06 20:00:03 +00:00
biofinish(bp, NULL, ENXIO);
Refine the detach/attach code. Proberly fail outstanding bio requests on devices that are detached. This makes it possible to change between disk/cdrom/dvd/whathaveyou in a notebook, just by suspending it, changing the device in the bay (or what you model calls it), unsuspend and the ATA driver will figure out what disappeared and properly fail those, and attach any new devices found.
2001-03-14 12:05:44 +00:00
return;
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
s = splbio();
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
bioqdisksort(&adp->queue, bp);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
splx(s);
Add new support for locking an ATA channel and use that throughout the ATA/ATAPI driver. This solves the concurrency problem with the new GEOM code, and also cuts a good deal of the patch size in the upcoming MFC.
2002-03-11 21:04:32 +00:00
ata_start(adp->device->channel);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
int
addump(dev_t dev)
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ad_softc *adp = dev->si_drv1;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
struct ad_request request;
Use micro "disk" layer in ata-disk Reviewed by: sos
1999-09-03 10:57:17 +00:00
u_int count, blkno, secsize;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
vm_offset_t addr = 0;
Implement write combining for crashdumps. This is useful when write caching is disabled on both SCSI and IDE disks where large memory dumps could take up to an hour to complete. Taking an i386 scsi based system with 512MB of ram and timing (in seconds) how long it took to complete a dump, the following results were obtained: Before: After: WCE TIME WCE TIME ------------------ ------------------ 1 141.820972 1 15.600111 0 797.265072 0 65.480465 Obtained from: Yahoo! Reviewed by: peter
2000-10-17 10:05:49 +00:00
long blkcnt;
int dumppages = MAXDUMPPGS;
Use micro "disk" layer in ata-disk Reviewed by: sos
1999-09-03 10:57:17 +00:00
int error;
Implement write combining for crashdumps. This is useful when write caching is disabled on both SCSI and IDE disks where large memory dumps could take up to an hour to complete. Taking an i386 scsi based system with 512MB of ram and timing (in seconds) how long it took to complete a dump, the following results were obtained: Before: After: WCE TIME WCE TIME ------------------ ------------------ 1 141.820972 1 15.600111 0 797.265072 0 65.480465 Obtained from: Yahoo! Reviewed by: peter
2000-10-17 10:05:49 +00:00
int i;
Use micro "disk" layer in ata-disk Reviewed by: sos
1999-09-03 10:57:17 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if ((error = disk_dumpcheck(dev, &count, &blkno, &secsize)))
return error;
Use micro "disk" layer in ata-disk Reviewed by: sos
1999-09-03 10:57:17 +00:00
if (!adp)
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
return ENXIO;
Add sysctl oid hw.atamodes to set the transfermodes online.
2000-01-27 19:00:51 +00:00
/* force PIO mode for dumps */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->mode = ATA_PIO;
ata_reinit(adp->device->channel);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
Implement write combining for crashdumps. This is useful when write caching is disabled on both SCSI and IDE disks where large memory dumps could take up to an hour to complete. Taking an i386 scsi based system with 512MB of ram and timing (in seconds) how long it took to complete a dump, the following results were obtained: Before: After: WCE TIME WCE TIME ------------------ ------------------ 1 141.820972 1 15.600111 0 797.265072 0 65.480465 Obtained from: Yahoo! Reviewed by: peter
2000-10-17 10:05:49 +00:00
blkcnt = howmany(PAGE_SIZE, secsize);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
while (count > 0) {
Quiet a silly warning. Pointy-hat to: ps
2000-10-19 18:52:20 +00:00
caddr_t va = NULL;
Fix IRQ allocation bug on controllers using a shared interrupt. Fix a bug which could cause panics in ad/atapi-interrupt. Add support for UDMA66 on Promise Ultra/Fasttrak controllers. Get rid of ATA_IGNORE_INTR, and introduce ATA_WAIT_INTR instead. Add a delay in the dump routine in ata-disk.c, some controllers seem to need this. Also dont use the timeout watchdog when dumping. Disable DMA on ATAPI devices as default, add option ATA_ENABLE_ATAPI_DMA for those that has HW that works. Add support for some not-up-to-spec ATAPI devices that returns data together with completition status on data moving cmd's.
1999-11-06 16:50:21 +00:00
DELAY(1000);
Implement write combining for crashdumps. This is useful when write caching is disabled on both SCSI and IDE disks where large memory dumps could take up to an hour to complete. Taking an i386 scsi based system with 512MB of ram and timing (in seconds) how long it took to complete a dump, the following results were obtained: Before: After: WCE TIME WCE TIME ------------------ ------------------ 1 141.820972 1 15.600111 0 797.265072 0 65.480465 Obtained from: Yahoo! Reviewed by: peter
2000-10-17 10:05:49 +00:00
if ((count / blkcnt) < dumppages)
dumppages = count / blkcnt;
for (i = 0; i < dumppages; ++i) {
vm_offset_t a = addr + (i * PAGE_SIZE);
if (is_physical_memory(a))
va = pmap_kenter_temporary(trunc_page(a), i);
else
va = pmap_kenter_temporary(trunc_page(0), i);
}
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
bzero(&request, sizeof(struct ad_request));
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
request.softc = adp;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
request.blockaddr = blkno;
Implement write combining for crashdumps. This is useful when write caching is disabled on both SCSI and IDE disks where large memory dumps could take up to an hour to complete. Taking an i386 scsi based system with 512MB of ram and timing (in seconds) how long it took to complete a dump, the following results were obtained: Before: After: WCE TIME WCE TIME ------------------ ------------------ 1 141.820972 1 15.600111 0 797.265072 0 65.480465 Obtained from: Yahoo! Reviewed by: peter
2000-10-17 10:05:49 +00:00
request.bytecount = PAGE_SIZE * dumppages;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
request.data = va;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
while (request.bytecount > 0) {
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
ad_transfer(&request);
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (request.flags & ADR_F_ERROR)
call ata_reinit in addump trying to make sure the dump will succed, also check for errors underways, and make it possible to abort the dump by hitting a key.
1999-11-27 17:06:10 +00:00
return EIO;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
request.donecount += request.currentsize;
Unbreak addump, now dumping works again.
2000-02-07 22:56:32 +00:00
request.bytecount -= request.currentsize;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
DELAY(20);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
Fix a signed bug in the crashdump code for systems with > 2GB of ram. Reviewed by: peter
2001-11-13 01:08:54 +00:00
if (dumpstatus(addr, (off_t)count * DEV_BSIZE) < 0)
Last commit was broken.. It always prints '[CTRL-C to abort]'. Move duplicate code for printing the status of the dump and checking for abort into a separate function. Pointy hat to: me
2001-03-28 01:37:29 +00:00
return EINTR;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
Implement write combining for crashdumps. This is useful when write caching is disabled on both SCSI and IDE disks where large memory dumps could take up to an hour to complete. Taking an i386 scsi based system with 512MB of ram and timing (in seconds) how long it took to complete a dump, the following results were obtained: Before: After: WCE TIME WCE TIME ------------------ ------------------ 1 141.820972 1 15.600111 0 797.265072 0 65.480465 Obtained from: Yahoo! Reviewed by: peter
2000-10-17 10:05:49 +00:00
blkno += blkcnt * dumppages;
count -= blkcnt * dumppages;
addr += PAGE_SIZE * dumppages;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_wait(adp->device, ATA_S_READY | ATA_S_DSC) < 0)
ata_prtdev(adp->device, "timeout waiting for final ready\n");
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
return 0;
}
Enable disksort the right way both on ATA disks and ATAPI devices.
2000-03-13 12:04:58 +00:00
void
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ad_start(struct ata_device *atadev)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
struct ad_softc *adp = atadev->driver;
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
struct bio *bp = bioq_first(&adp->queue);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
struct ad_request *request;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int tag = 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
if (!bp)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
return;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
Fix the breakage that snatched the ioports from the fdc device. Fix promise support.
2000-09-24 18:19:43 +00:00
/* if tagged queueing enabled get next free tag */
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
if (adp->flags & AD_F_TAG_ENABLED) {
while (tag <= adp->num_tags && adp->tags[tag])
tag++;
if (tag > adp->num_tags )
return;
}
Use M_ZERO flag on malloc when approbiate.
2000-12-26 12:05:49 +00:00
if (!(request = malloc(sizeof(struct ad_request), M_AD, M_NOWAIT|M_ZERO))) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(atadev, "out of memory in start\n");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
return;
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
}
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
/* setup request */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
request->softc = adp;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
request->bp = bp;
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
request->blockaddr = bp->bio_pblkno;
request->bytecount = bp->bio_bcount;
request->data = bp->bio_data;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
request->tag = tag;
Fix the breakage that snatched the ioports from the fdc device. Fix promise support.
2000-09-24 18:19:43 +00:00
if (bp->bio_cmd == BIO_READ)
request->flags |= ADR_F_READ;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->mode >= ATA_DMA) {
if (!(request->dmatab = ata_dmaalloc(atadev->channel, atadev->unit)))
adp->device->mode = ATA_PIO;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
/* insert in tag array */
adp->tags[tag] = request;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* remove from drive queue */
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
bioq_remove(&adp->queue, bp);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* link onto controller queue */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
TAILQ_INSERT_TAIL(&atadev->channel->ata_queue, request, chain);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
ad_transfer(struct ad_request *request)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
struct ad_softc *adp;
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
u_int64_t lba;
u_int32_t count, max_count;
u_int8_t cmd;
int flags = ATA_IMMEDIATE;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* get request params */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp = request->softc;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* calculate transfer details */
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
lba = request->blockaddr + (request->donecount / DEV_BSIZE);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
if (request->donecount == 0) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
/* start timeout for this transfer */
Do not allocate a callout for all crashdumps, not just when you panic.
2000-10-13 21:49:19 +00:00
if (dumping)
Fix IRQ allocation bug on controllers using a shared interrupt. Fix a bug which could cause panics in ad/atapi-interrupt. Add support for UDMA66 on Promise Ultra/Fasttrak controllers. Get rid of ATA_IGNORE_INTR, and introduce ATA_WAIT_INTR instead. Add a delay in the dump routine in ata-disk.c, some controllers seem to need this. Also dont use the timeout watchdog when dumping. Disable DMA on ATAPI devices as default, add option ATA_ENABLE_ATAPI_DMA for those that has HW that works. Add support for some not-up-to-spec ATAPI devices that returns data together with completition status on data moving cmd's.
1999-11-06 16:50:21 +00:00
request->timeout_handle.callout = NULL;
else
request->timeout_handle =
Relax the requirements for doing WDMA2, this should enable DMA on non ATA[234] compliant disks. Move all PCI dependent stuff under #ifdef NPCI > 0
1999-12-18 20:06:30 +00:00
timeout((timeout_t*)ad_timeout, request, 10 * hz);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Major update of the ATA RAID code, part 3: Add code to properly detach/attach disks that are part of a RAID. Mark a disk that is attached on an ATA channel belonging to a RAID as a spare disk that can be used for rebuilding failed RAID1's. Add support for rebuilding failed RAID1's. Several fixes to the detach/attach code. For replacing a disk in a failed RAID1 do the following: Find the controller channel# of the failed disk. Exec 'atacontrol detach <channel#>' to free the disk from the system. Replace the failed disk with a new one of at least the same size. If your have your disks in drawers/enclosures this can be done with the system still running. Exec 'atacontrol attach <channel#>' to add the disk to the system and mark it as a valid spare for rebuild. Exec 'atacontrol rebuild <array#>' The system will rebuild the array on the fly, the array can still be used during this, although with slower performance. Please let me know of any problems with this! Sponsored by: Advanis Inc. MFC after: 2 weeks
2002-03-03 15:36:21 +00:00
/* setup transfer parameters */
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
count = howmany(request->bytecount, DEV_BSIZE);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
max_count = adp->device->param->support.address48 ? 65536 : 256;
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
if (count > max_count) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device,
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
"count %d size transfers not supported\n", count);
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
count = max_count;
Support DMA on ATAPI devices (finally). This makes my system use only ~5% CPU on reading 4.5Mbyte/sec from a CDROM, which before was limitted to 1.8Mbyte/sec due to 100% CPU load..
1999-08-10 21:59:58 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
if (adp->flags & AD_F_CHS_USED) {
int sector = (lba % adp->sectors) + 1;
int cylinder = lba / (adp->sectors * adp->heads);
int head = (lba % (adp->sectors * adp->heads)) / adp->sectors;
lba = (sector&0xff) | ((cylinder&0xffff)<<8) | ((head&0xf)<<24);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->flags |= ATA_D_USE_CHS;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* setup first transfer length */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
request->currentsize = min(request->bytecount, adp->transfersize);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
devstat_start_transaction(&adp->stats);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* does this drive & transfer work with DMA ? */
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
request->flags &= ~ADR_F_DMA_USED;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->mode >= ATA_DMA &&
!ata_dmasetup(adp->device->channel, adp->device->unit,
request->dmatab, request->data, request->bytecount)) {
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
request->flags |= ADR_F_DMA_USED;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
request->currentsize = request->bytecount;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
/* do we have tags enabled ? */
if (adp->flags & AD_F_TAG_ENABLED) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
cmd = (request->flags & ADR_F_READ) ?
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ATA_C_READ_DMA_QUEUED : ATA_C_WRITE_DMA_QUEUED;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(adp->device, cmd, lba,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
request->tag << 3, count, flags)) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "error executing command");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
goto transfer_failed;
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_wait(adp->device, ATA_S_READY)) {
ata_prtdev(adp->device, "timeout waiting for READY\n");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
goto transfer_failed;
}
adp->outstanding++;
/* if ATA bus RELEASE check for SERVICE */
if (adp->flags & AD_F_TAG_ENABLED &&
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ATA_INB(adp->device->channel->r_io, ATA_IREASON) &
ATA_I_RELEASE)
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
return ad_service(adp, 1);
}
else {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
cmd = (request->flags & ADR_F_READ) ?
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ATA_C_READ_DMA : ATA_C_WRITE_DMA;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(adp->device, cmd, lba, count, 0, flags)) {
ata_prtdev(adp->device, "error executing command");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
goto transfer_failed;
}
#if 0
/*
Fix the breakage that snatched the ioports from the fdc device. Fix promise support.
2000-09-24 18:19:43 +00:00
* wait for data transfer phase
*
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
* well this should be here acording to specs, but older
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
* promise controllers doesn't like it, they lockup!
*/
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_wait(adp->device, ATA_S_READY | ATA_S_DRQ)) {
ata_prtdev(adp->device, "timeout waiting for data phase\n");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
goto transfer_failed;
}
#endif
}
/* start transfer, return and wait for interrupt */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_dmastart(adp->device->channel, adp->device->unit,
request->dmatab, request->flags & ADR_F_READ);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
return ATA_OP_CONTINUES;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add sysctl oid hw.atamodes to set the transfermodes online.
2000-01-27 19:00:51 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* does this drive support multi sector transfers ? */
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
if (request->currentsize > DEV_BSIZE)
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
cmd = request->flags&ADR_F_READ ? ATA_C_READ_MUL : ATA_C_WRITE_MUL;
Add sysctl oid hw.atamodes to set the transfermodes online.
2000-01-27 19:00:51 +00:00
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
/* just plain old single sector transfer */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
else
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
cmd = request->flags&ADR_F_READ ? ATA_C_READ : ATA_C_WRITE;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(adp->device, cmd, lba, count, 0, flags)){
ata_prtdev(adp->device, "error executing command");
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
goto transfer_failed;
Add sysctl oid hw.atamodes to set the transfermodes online.
2000-01-27 19:00:51 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* calculate this transfer length */
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
request->currentsize = min(request->bytecount, adp->transfersize);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* if this is a PIO read operation, return and wait for interrupt */
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (request->flags & ADR_F_READ)
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
return ATA_OP_CONTINUES;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* ready to write PIO data ? */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_wait(adp->device, (ATA_S_READY | ATA_S_DSC | ATA_S_DRQ)) < 0) {
ata_prtdev(adp->device, "timeout waiting for DRQ");
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
goto transfer_failed;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* output the data */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->channel->flags & ATA_USE_16BIT)
ATA_OUTSW(adp->device->channel->r_io, ATA_DATA,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
(void *)((uintptr_t)request->data + request->donecount),
request->currentsize / sizeof(int16_t));
Add support for the Intel 810 chipset (ICH type of chips) Prober support for the VIA 82C686, I finally got the right datasheet. Get rid of atapi_wait, merge it into ata_wait. Avoid a couple of races by using asleep instead of tsleep. Always use 16bit transfers on ISA systems. Clear up the atapi_read/write functions.
2000-01-17 02:04:19 +00:00
else
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ATA_OUTSL(adp->device->channel->r_io, ATA_DATA,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
(void *)((uintptr_t)request->data + request->donecount),
request->currentsize / sizeof(int32_t));
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
return ATA_OP_CONTINUES;
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
transfer_failed:
untimeout((timeout_t *)ad_timeout, request, request->timeout_handle);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, request);
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
printf(" - resetting\n");
/* if retries still permit, reinject this request */
if (request->retries++ < AD_MAX_RETRIES)
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
TAILQ_INSERT_HEAD(&adp->device->channel->ata_queue, request, chain);
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
else {
/* retries all used up, return error */
request->bp->bio_error = EIO;
request->bp->bio_flags |= BIO_ERROR;
request->bp->bio_resid = request->bytecount;
Actually biofinish(struct bio *, struct devstat *, int error) is more general than the bioerror(). Most of this patch is generated by scripts.
2001-05-06 20:00:03 +00:00
biofinish(request->bp, &adp->stats, 0);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_free(request);
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_reinit(adp->device->channel);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
return ATA_OP_CONTINUES;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
ad_interrupt(struct ad_request *request)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
struct ad_softc *adp = request->softc;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int dma_stat = 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* finish DMA transfer */
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (request->flags & ADR_F_DMA_USED)
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
dma_stat = ata_dmadone(adp->device->channel);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
/* do we have a corrected soft error ? */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->channel->status & ATA_S_CORR)
Cleanup the diskerr messages a bit.
2001-03-21 11:46:15 +00:00
diskerr(request->bp, "soft error (ECC corrected)",
Use diskerr for printing disk hard/soft errors.
2000-12-26 11:49:57 +00:00
request->blockaddr + (request->donecount / DEV_BSIZE),
&adp->disk.d_label);
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
/* did any real errors happen ? */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if ((adp->device->channel->status & ATA_S_ERROR) ||
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(request->flags & ADR_F_DMA_USED && dma_stat & ATA_BMSTAT_ERROR)) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->error =
ATA_INB(adp->device->channel->r_io, ATA_ERROR);
diskerr(request->bp, (adp->device->channel->error & ATA_E_ICRC) ?
"UDMA ICRC error" : "hard error",
Use diskerr for printing disk hard/soft errors.
2000-12-26 11:49:57 +00:00
request->blockaddr + (request->donecount / DEV_BSIZE),
&adp->disk.d_label);
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
/* if this is a UDMA CRC error, reinject request */
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (request->flags & ADR_F_DMA_USED &&
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->error & ATA_E_ICRC) {
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
untimeout((timeout_t *)ad_timeout, request,request->timeout_handle);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, request);
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
if (request->retries++ < AD_MAX_RETRIES)
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
printf(" retrying\n");
else {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_dmainit(adp->device->channel, adp->device->unit,
ata_pmode(adp->device->param), -1, -1);
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
printf(" falling back to PIO mode\n");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
TAILQ_INSERT_HEAD(&adp->device->channel->ata_queue, request, chain);
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
return ATA_OP_FINISHED;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
/* if using DMA, try once again in PIO mode */
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (request->flags & ADR_F_DMA_USED) {
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
untimeout((timeout_t *)ad_timeout, request,request->timeout_handle);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, request);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_dmainit(adp->device->channel, adp->device->unit,
ata_pmode(adp->device->param), -1, -1);
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
request->flags |= ADR_F_FORCE_PIO;
Minor cosmetic changes to minimise diffs for MFC.
2002-03-07 16:34:19 +00:00
printf(" trying PIO mode\n");
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
TAILQ_INSERT_HEAD(&adp->device->channel->ata_queue, request, chain);
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
return ATA_OP_FINISHED;
}
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
request->flags |= ADR_F_ERROR;
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
printf(" status=%02x error=%02x\n",
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->status, adp->device->channel->error);
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
}
/* if we arrived here with forced PIO mode, DMA doesn't work right */
Minor cosmetic changes to minimise diffs for MFC.
2002-03-07 16:34:19 +00:00
if (request->flags & ADR_F_FORCE_PIO && !(request->flags & ADR_F_ERROR))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "DMA problem fallback to PIO mode\n");
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* if this was a PIO read operation, get the data */
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (!(request->flags & ADR_F_DMA_USED) &&
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(request->flags & (ADR_F_READ | ADR_F_ERROR)) == ADR_F_READ) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
/* ready to receive data? */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if ((adp->device->channel->status & (ATA_S_READY|ATA_S_DSC|ATA_S_DRQ))
!= (ATA_S_READY|ATA_S_DSC|ATA_S_DRQ))
ata_prtdev(adp->device, "read interrupt arrived early");
if (ata_wait(adp->device, (ATA_S_READY | ATA_S_DSC | ATA_S_DRQ)) != 0) {
ata_prtdev(adp->device, "read error detected (too) late");
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
request->flags |= ADR_F_ERROR;
}
else {
/* data ready, read in */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->channel->flags & ATA_USE_16BIT)
ATA_INSW(adp->device->channel->r_io, ATA_DATA,
(void*)((uintptr_t)request->data + request->donecount),
request->currentsize / sizeof(int16_t));
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
else
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ATA_INSL(adp->device->channel->r_io, ATA_DATA,
(void*)((uintptr_t)request->data + request->donecount),
request->currentsize / sizeof(int32_t));
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
/* finish up transfer */
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (request->flags & ADR_F_ERROR) {
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
request->bp->bio_error = EIO;
request->bp->bio_flags |= BIO_ERROR;
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
}
else {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
request->bytecount -= request->currentsize;
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
request->donecount += request->currentsize;
if (request->bytecount > 0) {
ad_transfer(request);
return ATA_OP_CONTINUES;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
}
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
/* disarm timeout for this transfer */
untimeout((timeout_t *)ad_timeout, request, request->timeout_handle);
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
request->bp->bio_resid = request->bytecount;
Fix the breakage that snatched the ioports from the fdc device. Fix promise support.
2000-09-24 18:19:43 +00:00
Actually biofinish(struct bio *, struct devstat *, int error) is more general than the bioerror(). Most of this patch is generated by scripts.
2001-05-06 20:00:03 +00:00
biofinish(request->bp, &adp->stats, 0);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_free(request);
adp->outstanding--;
/* check for SERVICE (tagged operations only) */
return ad_service(adp, 1);
}
int
ad_service(struct ad_softc *adp, int change)
{
/* do we have to check the other device on this channel ? */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->channel->flags & ATA_QUEUED && change) {
int device = adp->device->unit;
if (adp->device->unit == ATA_MASTER) {
if (adp->device->channel->devices & ATA_ATA_SLAVE &&
((struct ad_softc *)
(adp->device->channel->
device[ATA_DEV(ATA_SLAVE)].driver))->flags&AD_F_TAG_ENABLED)
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
device = ATA_SLAVE;
}
else {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->channel->devices & ATA_ATA_MASTER &&
((struct ad_softc *)
(adp->device->channel->
device[ATA_DEV(ATA_MASTER)].driver))->flags&AD_F_TAG_ENABLED)
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
device = ATA_MASTER;
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (device != adp->device->unit &&
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
((struct ad_softc *)
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
(adp->device->channel->
device[ATA_DEV(device)].driver))->outstanding > 0) {
ATA_OUTB(adp->device->channel->r_io, ATA_DRIVE, ATA_D_IBM | device);
adp = adp->device->channel->device[ATA_DEV(device)].driver;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
DELAY(1);
}
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->status =
ATA_INB(adp->device->channel->r_altio, ATA_ALTSTAT);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
/* do we have a SERVICE request from the drive ? */
if (adp->flags & AD_F_TAG_ENABLED &&
Fix the breakage that snatched the ioports from the fdc device. Fix promise support.
2000-09-24 18:19:43 +00:00
adp->outstanding > 0 &&
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->status & ATA_S_SERVICE) {
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
struct ad_request *request;
int tag;
/* check for error */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->channel->status & ATA_S_ERROR) {
ata_prtdev(adp->device, "Oops! controller says s=0x%02x e=0x%02x\n",
adp->device->channel->status,
adp->device->channel->error);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, NULL);
return ATA_OP_FINISHED;
}
/* issue SERVICE cmd */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(adp->device, ATA_C_SERVICE, 0, 0, 0, ATA_IMMEDIATE)) {
ata_prtdev(adp->device, "problem executing SERVICE cmd\n");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, NULL);
return ATA_OP_FINISHED;
}
/* setup the transfer environment when ready */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_wait(adp->device, ATA_S_READY)) {
ata_prtdev(adp->device, "SERVICE timeout tag=%d s=%02x e=%02x\n",
ATA_INB(adp->device->channel->r_io, ATA_COUNT) >> 3,
adp->device->channel->status,
adp->device->channel->error);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, NULL);
return ATA_OP_FINISHED;
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
tag = ATA_INB(adp->device->channel->r_io, ATA_COUNT) >> 3;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
if (!(request = adp->tags[tag])) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "no request for tag=%d\n", tag);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, NULL);
return ATA_OP_FINISHED;
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->active = ATA_ACTIVE_ATA;
adp->device->channel->running = request;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
request->serv++;
/* start DMA transfer when ready */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_wait(adp->device, ATA_S_READY | ATA_S_DRQ)) {
ata_prtdev(adp->device, "timeout starting DMA s=%02x e=%02x\n",
adp->device->channel->status,
adp->device->channel->error);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, NULL);
return ATA_OP_FINISHED;
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_dmastart(adp->device->channel, adp->device->unit,
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
request->dmatab, request->flags & ADR_F_READ);
return ATA_OP_CONTINUES;
}
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
return ATA_OP_FINISHED;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static void
ad_free(struct ad_request *request)
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
{
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
if (request->dmatab)
free(request->dmatab, M_DEVBUF);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
request->softc->tags[request->tag] = NULL;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
free(request, M_AD);
}
static void
ad_invalidatequeue(struct ad_softc *adp, struct ad_request *request)
{
/* if tags used invalidate all other tagged transfers */
if (adp->flags & AD_F_TAG_ENABLED) {
struct ad_request *tmpreq;
int tag;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "invalidating queued requests\n");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
for (tag = 0; tag <= adp->num_tags; tag++) {
tmpreq = adp->tags[tag];
adp->tags[tag] = NULL;
if (tmpreq == request || tmpreq == NULL)
continue;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
untimeout((timeout_t *)ad_timeout, tmpreq, tmpreq->timeout_handle);
TAILQ_INSERT_HEAD(&adp->device->channel->ata_queue, tmpreq, chain);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (ata_command(adp->device, ATA_C_NOP,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
0, 0, ATA_C_F_FLUSHQUEUE, ATA_WAIT_READY))
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "flush queue failed\n");
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
adp->outstanding = 0;
}
}
static int
ad_tagsupported(struct ad_softc *adp)
{
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
const char *good[] = {"IBM-DPTA", "IBM-DTLA", NULL};
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int i = 0;
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
switch (adp->device->channel->chiptype) {
Update the Promise TX2 code to DTRT and not what I guessed earlier. Allow tagged queing on the Promise TX2 as it seems to work. Cudos to promise for making the most simple to program ATA chip.
2001-08-28 13:36:06 +00:00
case 0x4d33105a: /* Promises before TX2 doesn't work with tagged queuing */
case 0x4d38105a:
case 0x0d30105a:
case 0x4d30105a:
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
return 0;
Update the Promise TX2 code to DTRT and not what I guessed earlier. Allow tagged queing on the Promise TX2 as it seems to work. Cudos to promise for making the most simple to program ATA chip.
2001-08-28 13:36:06 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
/* check that drive does DMA, has tags enabled, and is one we know works */
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->mode >= ATA_DMA && adp->device->param->support.queued &&
adp->device->param->enabled.queued) {
while (good[i] != NULL) {
if (!strncmp(adp->device->param->model, good[i], strlen(good[i])))
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
return 1;
i++;
}
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
/*
* check IBM's new obscure way of naming drives
* we want "IC" (IBM CORP) and "AT" or "AV" (ATA interface)
* but doesn't care about the other info (size, capacity etc)
*/
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (!strncmp(adp->device->param->model, "IC", 2) &&
(!strncmp(adp->device->param->model + 8, "AT", 2) ||
!strncmp(adp->device->param->model + 8, "AV", 2)))
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
return 1;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
return 0;
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
static void
ad_timeout(struct ad_request *request)
{
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
struct ad_softc *adp = request->softc;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->channel->running = NULL;
ata_prtdev(adp->device, "%s command timeout tag=%d serv=%d - resetting\n",
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
(request->flags & ADR_F_READ) ? "READ" : "WRITE",
request->tag, request->serv);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
if (request->flags & ADR_F_DMA_USED) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_dmadone(adp->device->channel);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_invalidatequeue(adp, request);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (request->retries == AD_MAX_RETRIES) {
ata_dmainit(adp->device->channel, adp->device->unit,
ata_pmode(adp->device->param), -1, -1);
ata_prtdev(adp->device, "trying fallback to PIO mode\n");
Better error handeling: On UDMA CRC errors retry operation as it might be a fluke, if not fall back to PIO mode on the failing drive. If you get alot of these your cabeling is most likely not good enough. On HARD error using DMA, retry once using PIO, if it succeds using PIO fall back to PIO mode on the failing drive.
1999-11-29 12:24:51 +00:00
request->retries = 0;
}
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
/* if retries still permit, reinject this request */
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
if (request->retries++ < AD_MAX_RETRIES) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
TAILQ_INSERT_HEAD(&adp->device->channel->ata_queue, request, chain);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
else {
/* retries all used up, return error */
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
request->bp->bio_error = EIO;
request->bp->bio_flags |= BIO_ERROR;
Actually biofinish(struct bio *, struct devstat *, int error) is more general than the bioerror(). Most of this patch is generated by scripts.
2001-05-06 20:00:03 +00:00
biofinish(request->bp, &adp->stats, 0);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ad_free(request);
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
}
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_reinit(adp->device->channel);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
void
Fix buglets in the ATAPI resume code. This also fixes an old bug where some ATAPI devices went into funny mode on an 'atacontrol reinit' command.
2002-02-12 13:21:51 +00:00
ad_reinit(struct ata_device *atadev)
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
{
Fix buglets in the ATAPI resume code. This also fixes an old bug where some ATAPI devices went into funny mode on an 'atacontrol reinit' command.
2002-02-12 13:21:51 +00:00
struct ad_softc *adp = atadev->driver;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
/* reinit disk parameters */
Fix buglets in the ATAPI resume code. This also fixes an old bug where some ATAPI devices went into funny mode on an 'atacontrol reinit' command.
2002-02-12 13:21:51 +00:00
ad_invalidatequeue(atadev->driver, NULL);
ata_command(atadev, ATA_C_SET_MULTI, 0,
Minor cosmetic changes to minimise diffs for MFC.
2002-03-07 16:34:19 +00:00
adp->transfersize / DEV_BSIZE, 0, ATA_WAIT_READY);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
if (adp->device->mode >= ATA_DMA)
Fix buglets in the ATAPI resume code. This also fixes an old bug where some ATAPI devices went into funny mode on an 'atacontrol reinit' command.
2002-02-12 13:21:51 +00:00
ata_dmainit(atadev->channel, atadev->unit,
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_pmode(adp->device->param),
ata_wmode(adp->device->param),
ata_umode(adp->device->param));
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
else
Fix buglets in the ATAPI resume code. This also fixes an old bug where some ATAPI devices went into funny mode on an 'atacontrol reinit' command.
2002-02-12 13:21:51 +00:00
ata_dmainit(atadev->channel, atadev->unit,
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_pmode(adp->device->param), -1, -1);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
void
Major update of the ATA RAID code, part 3: Add code to properly detach/attach disks that are part of a RAID. Mark a disk that is attached on an ATA channel belonging to a RAID as a spare disk that can be used for rebuilding failed RAID1's. Add support for rebuilding failed RAID1's. Several fixes to the detach/attach code. For replacing a disk in a failed RAID1 do the following: Find the controller channel# of the failed disk. Exec 'atacontrol detach <channel#>' to free the disk from the system. Replace the failed disk with a new one of at least the same size. If your have your disks in drawers/enclosures this can be done with the system still running. Exec 'atacontrol attach <channel#>' to add the disk to the system and mark it as a valid spare for rebuild. Exec 'atacontrol rebuild <array#>' The system will rebuild the array on the fly, the array can still be used during this, although with slower performance. Please let me know of any problems with this! Sponsored by: Advanis Inc. MFC after: 2 weeks
2002-03-03 15:36:21 +00:00
ad_print(struct ad_softc *adp)
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
{
if (bootverbose) {
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "<%.40s/%.8s> ATA-%d disk at ata%d-%s\n",
adp->device->param->model, adp->device->param->revision,
ad_version(adp->device->param->version_major),
device_get_unit(adp->device->channel->dev),
(adp->device->unit == ATA_MASTER) ? "master" : "slave");
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device,
Update with latest ATA/ATAPI ver 6 rev 2 items.
2001-10-06 11:07:04 +00:00
"%lluMB (%llu sectors), %llu C, %u H, %u S, %u B\n",
Fix it so that it doesn't complain for compiles on alpha- that is, match format string args to actual args.
2001-10-14 19:44:15 +00:00
(unsigned long long)(adp->total_secs /
((1024L*1024L)/DEV_BSIZE)),
(unsigned long long) adp->total_secs,
(unsigned long long) (adp->total_secs /
(adp->heads * adp->sectors)),
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
adp->heads, adp->sectors, DEV_BSIZE);
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "%d secs/int, %d depth queue, %s%s\n",
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
adp->transfersize / DEV_BSIZE, adp->num_tags + 1,
(adp->flags & AD_F_TAG_ENABLED) ? "tagged " : "",
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_mode2str(adp->device->mode));
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device, "piomode=%d dmamode=%d udmamode=%d cblid=%d\n",
ata_pmode(adp->device->param), ata_wmode(adp->device->param),
ata_umode(adp->device->param),
adp->device->param->hwres_cblid);
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
}
else
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_prtdev(adp->device,"%lluMB <%.40s> [%lld/%d/%d] at ata%d-%s %s%s\n",
Fix it so that it doesn't complain for compiles on alpha- that is, match format string args to actual args.
2001-10-14 19:44:15 +00:00
(unsigned long long)(adp->total_secs /
((1024L * 1024L) / DEV_BSIZE)),
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
adp->device->param->model,
Fix it so that it doesn't complain for compiles on alpha- that is, match format string args to actual args.
2001-10-14 19:44:15 +00:00
(unsigned long long)(adp->total_secs /
(adp->heads*adp->sectors)),
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
adp->heads, adp->sectors,
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
device_get_unit(adp->device->channel->dev),
(adp->device->unit == ATA_MASTER) ? "master" : "slave",
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
(adp->flags & AD_F_TAG_ENABLED) ? "tagged " : "",
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
ata_mode2str(adp->device->mode));
Add sysctls for reading the tunables as suggested by des. Minor cleanups plus checks of the ->active state. Cosmetics.
2001-03-19 08:04:54 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
ad_version(u_int16_t version)
{
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int bit;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (version == 0xffff)
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
return 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
for (bit = 15; bit >= 0; bit--)
if (version & (1<<bit))
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
return bit;
return 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Reference in New Issue Copy Permalink