The logical result of a right shift >= the width of a type is zero, but our
compiler decides this is a warning (and thus, error). Just remove ccp(4)
from i386.
Reported by: cy
Sponsored by: Dell EMC Isilon
* Registers TRNG source for random(4)
* Finds available queues, LSBs; allocates static objects
* Allocates a shared MSI-X for all queues. The hardware does not have
separate interrupts per queue. Working interrupt mode driver.
* Computes SHA hashes, HMAC. Passes cryptotest.py, cryptocheck tests.
* Does AES-CBC, CTR mode, and XTS. cryptotest.py and cryptocheck pass.
* Support for "authenc" (AES + HMAC). (SHA1 seems to result in
"unaligned" cleartext inputs from cryptocheck -- which the engine
cannot handle. SHA2 seems to work fine.)
* GCM passes for block-multiple AAD, input lengths
Largely based on ccr(4), part of cxgbe(4).
Rough performance averages on AMD Ryzen 1950X (4kB buffer):
aesni: SHA1: ~8300 Mb/s SHA256: ~8000 Mb/s
ccp: ~630 Mb/s SHA256: ~660 Mb/s SHA512: ~700 Mb/s
cryptosoft: ~1800 Mb/s SHA256: ~1800 Mb/s SHA512: ~2700 Mb/s
As you can see, performance is poor in comparison to aesni(4) and even
cryptosoft (due to high setup cost). At a larger buffer size (128kB),
throughput is a little better (but still worse than aesni(4)):
aesni: SHA1:~10400 Mb/s SHA256: ~9950 Mb/s
ccp: ~2200 Mb/s SHA256: ~2600 Mb/s SHA512: ~3800 Mb/s
cryptosoft: ~1750 Mb/s SHA256: ~1800 Mb/s SHA512: ~2700 Mb/s
AES performance has a similar story:
aesni: 4kB: ~11250 Mb/s 128kB: ~11250 Mb/s
ccp: ~350 Mb/s 128kB: ~4600 Mb/s
cryptosoft: ~1750 Mb/s 128kB: ~1700 Mb/s
This driver is EXPERIMENTAL. You should verify cryptographic results on
typical and corner case inputs from your application against a known- good
implementation.
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D12723
Since r326501 which added COMPAT_FREEBSD32 to the GENERIC config for arm64,
we need to build systrace_freebsd32, since dtraceall depends on it.
Reviewed by: ed, gnn
Differential Revision: https://reviews.freebsd.org/D13670
The ep(4) driver is the only consumer of the two functions from
elink.c. I removed the standalone module as well, and most likely,
the module metadata is not needed anywhere, but this is for later
cleanup.
Discussed with: imp, jhb
Sponsored by: The FreeBSD Foundation
Initial update to the ixgbe PF and VF drivers to support the iflib interface.
The PF driver version is bumped to 4.0.0, and the VF driver version is bumped to 2.0.0.
Special thanks to sbruno@ for the support in helping make this conversion happen.
Submitted by: Jeb Cramer <cramerj@intel.com>, Krzysztof Galazka (Chris) <krzysztof.galazka@intel.com>, Piotr Pietruszewski <piotr.pietruszewski@intel.com>
Reviewed by: sbruno@, shurd@, #IntelNetworking
Tested by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>, Sergey Kozlov <kozlov.sergey.404@gmail.com>
Sponsored by: Limelight Networks, Intel Corporation
Differential Revision: https://reviews.freebsd.org/D11727
sinovoip-bpi-m3.dts was disconnected from the build in r324822. Since then,
a CCU driver has been added and several other changes have been made to
make us compatible with upstream DTS for this board.
Add links for older DTB that might be used: our u-boot port was expecting
sinovoip-bpi-m3.dtb up until ports r455629, and our u-boot will not be
switching to the upstream name (sun8i-a83t-bananapi-m3) quite yet.
Discussed with: manu
The OBJS_DEPEND_GUESS mechanism was making vmx_genassym.o depend
on all headers along with vmx_assym.h, though vmx_assym.h depends
on having vmx_genassym.o present to generate. Moving the headers
to DPSRCS is enough to resolve the issue as they will no longer
be implicit dependencies for all objects. Because of this we
need explicit OBJS_DEPEND_GUESS entries to ensure the headers
are generated when needed for the *_support.o files that need
them.
X-MFC-With: r326552
MFC after: 2 weeks
Sponsored by: Dell EMC
Currently, bwn(4) relies on the siba_bwn(4) bus driver to provide support
for the on-chip SSB interconnect found in Broadcom's older PCI(e) Wi-Fi
adapters. Non-PCI Wi-Fi adapters, as well as the newer BCMA interconnect
found in post-2009 Broadcom Wi-Fi hardware, are not supported by
siba_bwn(4).
The bhnd(4) bus driver (also used by the FreeBSD/MIPS Broadcom port)
provides a unified kernel interface to a superset of the hardware supported
by siba_bwn; by attaching bwn(4) via bhnd(4), we can support both modern
PCI(e) Wi-Fi devices based on the BCMA backplane interconnect, as well as
Broadcom MIPS WiSoCs that include a D11 MAC core directly attached to their
SSB or BCMA backplane.
This diff introduces opt-in bwn(4) support for bhnd(4) by providing:
- A small bwn(4) driver subclass, if_bwn_bhnd, that attaches via
bhnd(4) instead of siba_bwn(4).
- A bhndb(4)-based PCI host bridge driver, if_bwn_pci, that optionally
probes at a higher priority than the siba_bwn(4) PCI driver.
- A set of compatibility shims that perform translation of bwn(4)'s
siba_bwn function calls into their bhnd(9) API equivalents when bwn(4)
is attached via a bhnd(4) bus parent. When bwn(4) is attached via
siba_bwn(4), all siba_bwn function calls are simply passed through to
their original implementations.
To test bwn(4) with bhnd(4), place the following lines in loader.conf(5):
hw.bwn_pci.preferred="1"
if_bwn_pci_load="YES
bwn_v4_ucode_load="YES"
bwn_v4_lp_ucode_load="YES"
To verify that bwn(4) is using bhnd(4), you can check dmesg:
bwn0: <Broadcom 802.11 MAC/PHY/Radio, rev 15> ... on bhnd0
... or devinfo(8):
pcib2
pci2
bwn_pci0
bhndb0
bhnd0
bwn0
...
bwn(4)/bhnd(4) has been tested for regressions with most chipsets currently
supported by bwn(4), including:
- BCM4312
- BCM4318
- BCM4321
With minimal changes to the DMA code (not included in this commit), I was
also able to test support for newer BCMA devices by bringing up basic
working Wi-Fi on two previously unsupported, BCMA-based N-PHY chipsets:
- BCM43224
- BCM43225
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation & Plausible Labs
Differential Revision: https://reviews.freebsd.org/D13041
This change adds an implementation of a sysent for running CloudABI
armv6 and armv7 binaries on FreeBSD/arm64. It is a somewhat literal copy
of the armv6 version, except that it's been patched up to use the proper
registers.
Just like for cloudabi32.ko on FreeBSD/amd64, we make use of a vDSO that
automatically pads system call parameters to 64-bit value. These are
stored in a buffer on the stack, meaning we need to use copyin() and
copyout() unconditionally.
Very early BHND Wi-Fi devices (e.g. BCM4318) do not support any form of
dynamic clock control; on these devices, any PMU requests that cannot be
met by the device's fixed clock state will return an appropriate error
code.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
This commit merges projects/bsd_rdma_4_9 to head.
List of kernel sources used:
============================
1) kernel sources were cloned from git://github.com/torvalds/linux.git
Top commit 69973b830859bc6529a7a0468ba0d80ee5117826 - tag: v4.9, linux-4.9
2) krping was cloned from https://github.com/larrystevenwise/krping
Top commit 292a2f1abf0348285e678a82264740d52e4dcfe4
List of userspace sources used:
===============================
1) rdma-core was cloned from https://github.com/linux-rdma/rdma-core.git
Top commit d65138ef93af30b3ea249f3a84aa6a24ba7f8a75
2) OpenSM was cloned from git://git.openfabrics.org/~halr/opensm.git
Top commit 85f841cf209f791c89a075048a907020e924528d
3) libibmad was cloned from git://git.openfabrics.org/~iraweiny/libibmad.git
Tag 1.3.13 with some additional patches from Mellanox.
4) infiniband-diags was cloned from git://git.openfabrics.org/~iraweiny/infiniband-diags.git
Tag 1.6.7 with some additional patches from Mellanox.
NOTES:
======
1) The mthca driver has been removed in kernel and in userspace.
2) All GPLv2 only sources have been removed and where applicable
rewritten from scratch under a BSD license.
3) List of fully supported drivers in userspace and kernel:
a) iw_cxgbe (Chelsio)
b) mlx4ib (Mellanox)
c) mlx5ib (Mellanox)
4) WITH_OFED=YES is still required by make in order to build
OFED userspace and kernel code.
5) Full support has been added for routable RoCE, RoCE v2.
Sponsored by: Mellanox Technologies
The recently imported cloudabi_vdso_armv6_on_64bit.S should be the vDSO
for 32-bit processes when being run on FreeBSD/arm64. This vDSO ensures
that all system call arguments are padded to 64 bits, so that they can
be used by the kernel to call into most of the native implementations
directly.
The driver is functional on both BHND Wi-Fi adapters and MIPS SoCs, but
does not currently include support for features not required by bwn(4),
including GPIO interrupt handling.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12708
The bwn(4) driver requires a number of extensions to the bhnd(4) PMU
interface to support external configuration of PLLs, LDOs, and other
parameters that require chipset or PHY-specific workarounds.
These changes add support for:
- Writing raw voltage register values to PHY-specific LDO regulator
registers (required by LP-PHY).
- Enabling/disabling PHY-specific LDOs (required by LP-PHY)
- Writing to arbitrary PMU chipctrl registers (required for common PHY PLL
reset support).
- Requesting chipset/PLL-specific spurious signal avoidance modes.
- Querying clock frequency and latency.
Additionally, rather than updating legacy PWRCTL support to conform to the
new PMU interface:
- PWRCTL API is now provided by a bhnd_pwrctl_if.m interface.
- Since PWRCTL is only found in older SSB-based chipsets, translation from
bhnd(4) bus APIs to corresponding PWRCTL operations is now handled
entirely within the siba(4) driver.
- The PWRCTL-specific host bridge clock gating APIs in bhnd_bus_if.m have
been lifted out into a standalone bhnd_pwrctl_hostb_if.m interface.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12664
the system time.
As we seem to only read this time on boot, and this is the only source of
time on many arm64 machines we need to enable this by default there. As
this is not always the case with U-Boot firmware, or when we have been
booted from a non-UEFI environment we only enable the device driver when
the Runtime Services are present and reading the time doesn't result in an
error.
PR: 212185
Reviewed by: imp, kib
Tested by: emaste
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12650
IPsec support can be loaded as kernel module, thus do not depend from
kernel option IPSEC and always build O_IPSEC opcode implementation as
enabled.
Obtained from: Yandex LLC
MFC after: 1 week
Sponsored by: Yandex LLC
Background:
The coming ibcore update forces an update of mlx4ib(4) which in turn requires
an updated mlx4 core module. This also affects the mlx4en(4) module because
commonly used APIs are updated. This commit is a middle step updating the
mlx4 modules towards the new ibcore.
This change contains no major new features.
Changes in mlx4:
a) Improved error handling when mlx4 PCI devices are
detached inside VMs.
b) Major update of codebase towards Linux 4.9.
Changes in mlx4ib(4):
a) Minimal changes needed in order to compile using the
updated mlx4 core APIs.
Changes in mlx4en(4):
a) Update flow steering code in mlx4en to use new APIs for
registering MAC addresses and IP addresses.
b) Update all statistics counters to be 64-bit.
c) Minimal changes needed in order to compile using the
updated mlx4 core APIs.
Sponsored by: Mellanox Technologies
MFC after: 1 week
the coming ibcore and mlx5ib updates in order to support traffic redirection
to so-called raw ethernet QPs.
Remove unused E-switch related routines and files while at it.
Sponsored by: Mellanox Technologies
MFC after: 1 week
mbpool existed to support NICs with memory interfaces and all remaining
comsumers were removed earlier this year with NATM.
Reviewed by: jhb
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D10513
this is more friendly to the tree.
Tested this with loader.conf:if_igb_load="YES" and it does the right
thing.
Submitted by: Ian Lepore <ian@freebsd.org>
mapping. This uses the new common code shared with amd64.
The RTC should only be accessed via EFI. There is no locking around it as
the spec only has this as a requirement for the PC-AT CMOS device.
Reviewed by: kib, imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12595
end up with non-standard DESTDIR information in its symlink. This
can happen very trivially if the release scripts are used.
Sponsored by: Limelight Networks
Changes since 1.16.26.0 for all three firmwares are listed below. This
list was obtained from the Release Notes of the Chelsio Unified Wire
v3.5.05 release for Linux.
T6 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
BASE:
- Fixed a fw crash when configured traffic rate limit is less than 10kbps.
- Fixed traffic rate limiting for smaller traffic rate value.
ETH:
- Fixed 40G link failure when interface is toggled.
- Fixed adapter crash when interface is toggled during traffic.
- Fixed 25G link failure when PEER only supports consortium mode autoneg
for 25G.
- Fixed 100G optics link failure when cable is plugged in after bringing up
the interface.
- Enable RS FEC as default if speed is 100G.
- Fixed DCBX configuration refresh failure.
OFLD
- Fixed 0B iWARP ingress read failure.
- Fixed iWARP SRQ reuse failure.
FOiSCSI:
- Fixed vlan interface ping failure.
- Fixed target discovery failures.
- Fixed mutual chap login failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed fw crash caused by MC parity error in SO adapters.
- Generate Timer0Int interrupt if fw crashes due to unaligned access error. Host
driver must look into PCIE_FW register to see if any fw fatal error has
encountered. If PCIE_FW doesn't indicate any error then driver must ignore this
interrupt.
- Fixed receive buffer threshold settings which was resulting in error frames on
receive side.
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
check.
- Fixed improper LED behaviour for blink test and when traffic is running.
- Removed storage of previous fec settings from fw. Driver needs to pass the user
settings whenever a new module is plugged in as fw resets these when a module is
unplugged.
OFLD
- OVS offload: TP cache is flushed periodically to get the accuate filters stats
(hit count).
ENHANCEMENTS
------------
BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
added to query and enable ring backbone support.
- VNI support added for filtering. New entry_type FW_VI_MAC_TYPE_EXACTMAC_VNI
added to FW_VI_MAC_CMD.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
- HMA (Host memory access) support added. New FW_HMA_CMD and
FW_PARAMS_PARAM_DEV_HMA_SIZE added to query and configure the HMA. It
enables the memfree support (256 connections) for iwarp.
- PTP support enabled.
ETH:
- Added consortium mode 50G support.
- Added the ability to allow only selected speeds to be advertised during auto
negotiation.
- Increased port capability from 16 to 32 bits to support more speeds.
FW_PARAMS_PARAM_PFVF_PORT_CAPS32 added to query whether fw supports 16 or 32
bit port capability.
OFLD:
- RDMA Write with immediate support added (iwarp 2.0 feature)
- FW_TLS_KEYCTX_TX_WR removed and security key management moved to driver.
- 256 offloaded connections support for iwarp on SO adapters.
iSCSI:
- New param FW_PARAMS_PARAM_DEV_PPOD_EDRAM added for iscsi ppod configuration
in EDRAM (performance improvement).
FOiSCSI:
- iSCSI Command offload target support added.
FOFCoE:
- FCoE support enabled.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
- Fixed DDR3/DDR4 ECC errors.
- Fixed an FLR issue where FLR completion was going to host before FLR
processing is finished in fw.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
after loading the driver.
- Fixed false link up when peer interface was brought down.
- Enabling RS FEC by default for 100Gbase-SR4 according to 802.3BJ standard.
- Fixed bugs related to negotiated fec based local/peer fec ability and request.
- Fixed auto-neg failure with few switches.
- T6 Performance improvement fixes.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
- T6 Crypto Coprocessor mode bug fixes.
- T6 Crypto TLS-inline mode bug fixes.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
ETH:
- Added broadcom consortium next page support for 25G CR.
This can be enabled using flags=an_brcm option in the t6-config.txt file.
- Added spider mode support.
- Added support for 10G-BaseT converter sfp+ module.
- Added support for additional 25G/100G cables.
- Added support to enable/disable auto-neg using ethtool.
================================================================================
Version : 1.16.33.0
Date : 02/24/2017
================================================================================
Fixes
-----
BASE:
- Fixed DDR4 uncorrectable errors.
ETH:
- Enabled link auto negotiation (AN) by default in config file.
- Added AN and FEC control api. Host driver and application can enable/disable
AN and FEC.
ENHANCEMENTS
------------
BASE:
- Enabled High priorty filter.
- Added T6425 adapter support.
ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).
================================================================================
Version : 1.16.29.0
Date : 01/27/2017
================================================================================
FIXES
-----
BASE:
- Set multiple fec values only if AN is enabled in config file and when module
is connected.
- Fixed intermittent DDR3/4 ECC errors.
- max number of ethctrl queue in VF set to 2 (reverted the last change
because it causes problem in VF drivers).
ETH:
- Made devlog more verbose by printing cable information in redable form.
- Updated AN settings to work with more 25G/100G switches.
- Added support for more SFP28/QSFP28 cables.
- Fixed an issue of link going down after few hours of idle time.
OFLD:
- Fixed an issue in TLS which was causing fw crash on running TLS traffic.
FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.
ENHANCEMENTS
------------
OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.
================================================================================
T5 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
BASE:
- Fixed offload memory overcommit in case of SO adapter.
ETH:
- Fixed DCBX configuration refresh failure.
OFLD
- Fixed 0B iWARP ingress read failure.
FOiSCSI:
- Fixed vlan interface ping failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed an FLR issue which was causing error when VF attached VM was powered on.
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
check.
- Fixed T580 link failure with few switches which take more time for
establishing link.
ENHANCEMENTS
------------
BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
added to query and enable ring backbone support.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
FOiSCSI:
- iSCSI Command offload target support added.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
after loading the driver.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
================================================================================
Version : 1.16.33.0
Date : 02/24/2017
================================================================================
ENHANCEMENTS
------------
ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).
================================================================================
Version : 1.16.29.0
Date : 01/27/2017
================================================================================
FIXES
-----
BASE:
- max number of ethctrl queue in VF set to 2 (reverted the last change
because it causes problem in VF drivers).
FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.
ENHANCEMENTS
------------
OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.
================================================================================
T4 Firmware
+++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
ETH:
- Fixed DCBX configuration refresh failure.
FOiSCSI:
- Fixed vlan interface ping failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
ENHANCEMENTS
------------
BASE:
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
Obtained from: Chelsio Communications
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Make armv7 as a new MACHINE_ARCH.
Copy all the places we do armv6 and add armv7 as basically an
alias. clang appears to generate code for armv7 by default. armv7 hard
float isn't supported by the the in-tree gcc, so it hasn't been
updated to have a new default.
Support armv7 as a new valid MACHINE_ARCH (and by extension
TARGET_ARCH).
Add armv7 to the universe build.
Differential Revision: https://reviews.freebsd.org/D12010
machine independent parts of the existing code to a new file that can be
shared between amd64 and arm64.
Reviewed by: kib (previous version), imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12434
