The <uchar.h> header, part of C11, adds a small number of utility
functions for 16/32-bit "universal" characters, which may or may not be
UTF-16/32. As our wchar_t is already ISO 10646, simply add light-weight
wrappers around wcrtomb() and mbrtowc().
While there, also add (non-yet-standard) _l functions, similar to the
ones we already have for the other locale-dependent functions.
Reviewed by: theraven
r124183: Work around a `label defined but not used' warning.
r179549: De-register declarations.
r179657: De-register declarations in non-dot-c files.
r181269: Mark yy_fatal_error() as __dead2.
r228992: Spelling fixes.
r240518: Correct double "the the".
traffic.
When transmitting non-aggregate traffic, we need to keep the hardware
busy whilst transmitting or small bursts in txdone/tx latency will
kill us.
This restores non-aggregate iperf performance, especially when doing
TDMA.
Tested:
* AR5416<->AR5416, TDMA
* AR5416 STA <-> AR9280 AP
of course.)
There's a few things that needed to happen:
* In case someone decides to set the beacon transmission rate to be
at an MCS rate, use the MCS-aware version of the duration calculation
to figure out how long the received beacon frame was.
* If TxOP enforcing is available on the hardware and we're doing TDMA,
enable it after a reset and set the TDMA guard interval to zero.
This seems to behave fine.
TODO:
* Although I haven't yet seen packet loss, the PHY errors that would be
triggered (specifically Transmit-Override-Receive) aren't enabled
by the 11n HAL. I'll have to do some work to enable these PHY errors
for debugging.
What broke:
* My recent changes to the TX queue handling has resulted in the driver
not keeping the hardware queue properly filled when doing non-aggregate
traffic. I have a patch to commit soon which fixes this situation
(albeit by reminding me about how my ath driver locking isn't working
out, sigh.)
So if you want to test this without updating to the next set of patches
that I commit, just bump the sysctl dev.ath.X.hwq_limit from 2 to 32.
Tested:
* AR5416 <-> AR5416, with ampdu disabled, HT40, 5GHz, MCS12+Short-GI.
I saw 30mbit/sec in both directions using a bidirectional UDP test.
the system compiler is not clang. clang and gcc appear to differ
signficantly in their interpretation of -isystem and --sysroot. Further
work is likely required to support an external gcc.
Reported by: andreast, fidaj@ukr.net, sergey.dyatko@gmail.com
the right type for the argument in syscalls.master. Also fix the
posix_fallocate(2) and posix_fadvise(2) compat32 syscalls on the
architectures which require padding of the 64bit argument.
Noted and reviewed by: jhb
Pointy hat to: kib
MFC after: 1 week
for the case when the nullfs vnode is not reclaimed. Otherwise, later
reclamation would not unlock the lower vnode.
Reported by: antoine
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
registers also on other CPUs, besides the CPU which happens to execute
the ddb. The debugging registers are stored in the pcpu area,
together with the command which is executed by the IPI stop handler
upon resume.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
a vm page, denoted either by an address of the struct vm_page, or, if
the '/p' modifier is specified, by a physical address of the
corresponding frame.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
1. Common headers for fdt.h and ofw_machdep.h under x86/include
with indirections under i386/include and amd64/include.
2. New modinfo for loader provided FDT blob.
3. Common x86_init_fdt() called from hammer_time() on amd64 and
init386() on i386.
4. Split-off FDT specific low-level console functions from FDT
bus methods for the uart(4) driver. The low-level console
logic has been moved to uart_cpu_fdt.c and is used for arm,
mips & powerpc only. The FDT bus methods are shared across
all architectures.
5. Add dev/fdt/fdt_x86.c to hold the fdt_fixup_table[] and the
fdt_pic_table[] arrays. Both are empty right now.
FDT addresses are I/O ports on x86. Since the core FDT code does
not handle different address spaces, adding support for both I/O
ports and memory addresses requires some thought and discussion.
It may be better to use a compile-time option that controls this.
Obtained from: Juniper Networks, Inc.
If 'e' is used, the kernel must support the recently added pipe2() system
call.
The use of pipe2() with O_CLOEXEC also fixes race conditions between
concurrent popen() calls from different threads, even if the close-on-exec
flag on the fd of the returned FILE is later cleared (because popen() closes
all file descriptors from earlier popen() calls in the child process).
Therefore, this approach should be used in all cases when pipe2() can be
assumed present.
The old version of popen() rejects "re" and "we" but treats "r+e" like "r+".
Change several int variables to size_t, ssize_t, or ptrdiff_t.
This should fix the bug described in CVE-2012-5667 when an input
line is so long that its length cannot be stored in an int
variable.
This is based on NetBSD's revision which says:
This change to NetBSD's version of GNU grep 2.5.1 (licenced under
GPLv2) was made without direct reference to any code licenced
under GPLv3.
Obtained from: NetBSD
MFC after: 3 days
