on friday 13th and without making a universe). This adds struct and
constant definitions for ATM traffic parameters and re-enables the
build of the midway driver.
Tested by: make universe
don't reveal the info in reply to the SYST command.
Get rid of using the "unix" macro at the same time. It was a rather
poor way to check if the system was Unix since there were quite a
few Unix clones out there whose cc didn't define "unix" (e.g.,
NetBSD.) It was also sensitive to the C standard used, which caused
unnecessary trouble: With -std=c99, it should have been "__unix__",
and so on.
PR: bin/50690
Submitted by: Alex Semenyaka <alexs _at_ snark.ratmir.ru>
MFC after: 1 week
Previously, any normal I/O on an fdc(4) device would fail with ENXIO
if the device had been opened in non-blocking mode and then closed
prior to the conventional access; that would last until the floppy
disk was ejected and re-inserted to raise the unit attention condition.
Add a clarifying comment.
header file differences between FBSD and NBSD. Like lukemftpd, the
portable version of lukemftp lags too far behind CVS.
This import includes several big fixes plus a cleaned up manpage.
populated. Apparently, if you use an ehci controller, it's not.
Use usbd_device2interface_handle() to retrieve the interface handle.
NOTE: uaa->iface is populated in the probe routine, so I suspect the
fact that it's NULL in the attach routine is a bug in the ehci driver.
Also, don't depend on the PHY addresses returned by the AXE_CMD_READ_PHYID
command. The address is correct for my LinkSys NIC, but a user has
reported that with a D-Link NIC, the PHYID command returns address 4
while the attached Broadcom PHY is in fact strapped for address 0.
Instead, latch onto the first PHY address that returns valid data
during a readreg operation.
Only call pw_mkdb if passfile == _PATH_MASTERPASSWD.
Otherwise, rename master.passwd to a temp filename, rename
the new passwd to master.passwd, and let yppwupdate update
passwd as it sees fit.
Reviewed by: phk
Tested by: genesys
- Add vm page queue locking in certain places that are only needed on
sparc64.
This should make pmap_qenter and pmap_qremove MP-safe.
Discussed with: alc
as should every block device strategy routine.
There was at least one evil consequence of not doing so:
Some errors returned by fdstrategy() could be lost (EAGAIN,
in particular.)
PR: kern/52338 (in the audit-trail)
Discussed with: bde
to access floppy parameters through it.
Note: The DIOCGSECTORSIZE and DIOCGMEDIASIZE handlers withing
fdioctl() couldn't be just moved to below the existing check
for blocking mode because fd->ft can be non-NULL while still
in non-blocking mode (fd->ft can be set with the FD_STYPE ioctl.)
PR: kern/52338
No MFC: Not applicable to STABLE
Remove a reference to the defunct macro M_COPY_PKTHDR;
document the new functions m_dup_pkthdr() and m_move_pkthdr(),
and the macro variant of the latter, M_MOVE_PKTHDR().
- tagging plaintext "mbuf", "mbuf cluster", and "mbuf chain"
with .Vt (variable type) since all of them are ways of managing
data, i.e., they can be seen as data types;
- using .Vt/.Va instead of .Li (literal) where appropriate;
- tagging plaintext words that actually refer to function arguments
with .Fa.
Suggested by: ru
schedules an upcall. Signal delivering to a bound thread is same as
non-threaded process. This is intended to be used by libpthread to
implement PTHREAD_SCOPE_SYSTEM thread.
2. Simplify kse_release() a bit, remove sleep loop.
ulpt_status() afterwards. This fixes a crash that can occur if a
USB printer is power-cycled when printing is just starting. The
problem is similar to that fixed in revision 1.33, but it is much
less likely to occur.
MFC after: 1 week
panics. Before revision 1.38, we used to just point panicstr at the
format string if panicstr was NULL, but since we now use a static
buffer for the formatted panic message, we have to be careful to
only write to it during the first panic.
Pointed out by: bde
