Systematically use ANSI C functions definitions.
Correct type of the flags argument to the dev_pager_putpages() function.
Use vm_pager_free_nonreq().
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
On ARM, we must ensure proper interdevice write ordering.
The AHCI interrupt status register must be updated in HW before
registers in interrupt controller.
Unfortunately, only way how we can do it is readback.
Discussed with: mav
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D4240
This is a 2x2 2GHz 802.11n part. It works enough at the moment to
bring up, scan and associate. I haven't started using this as
a day to day AP.
The specifics:
* add honeybee initvals
* add in changes; a mix from the QCA HAL and ath9k;
* fix a bug in AR_SREV_AR9580_10_OR_LATER(), which is only used
for one capability check and we don't even implement it - so it's
a big no-op.
Shady things:
* ath9k has the "platform data" define the 25/40MHz clock.
This HAL .. doesn't. Honeybee gets hard-coded to 25MHz which
it likely shouldn't be. I'll have to go and identify/fix those.
Tested:
* Qualcomm Atheros AP143 reference design board.
Obtained from: Qualcomm Atheros; Linux ath9k
Using a typedef for common code return types (rather than "int")
allows the Prefast static analyser to understand when a function
has been successful (and thus when its postconditions must hold).
This greatly reduces then number of false positives reported by
prefast for error paths in common code functions.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Dynamic config partitions on boards that support RFID are divided into
a number of segments, each formatted like a partition, with header,
trailer and end tags. The first segment is the current active
configuration.
The segments are initialised by manftest and each contain a different
configuration e.g. firmware variant. The firmware can be instructed
via RFID to copy a segment over the first segment, hence changing the
active configuration. This allows ops to change the configuration of
a board prior to shipment using RFID.
Changes to the dynamic config may need to be written to all segments (in
particular firmware versions written by manftest) or just the first
segment (changes to the active configuration). See SF-111324-SW.
If only the first segment is written the code still needs to be aware of
the possible presence of subsequent segments as writing to a segment may
cause its size to increase, which would overwrite the subsequent
segments and invalidate them.
Boards that do not support RFID will only have one segment in their
dynamic config partition.
Submitted by: Paul Fox <pfox at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D4302
sysent.
sv_prepsyscall is unused.
sv_sigsize and sv_sigtbl translate signal number from the FreeBSD
namespace into the ABI domain. It is only utilized on i386 for iBCS2
binaries. The issue with this approach is that signals for iBCS2 were
delivered with the FreeBSD signal frame layout, which does not follow
iBCS2. The same note is true for any other potential user if
sv_sigtbl. In other words, if ABI needs signal number translation, it
really needs custom sv_sendsig method instead.
Sponsored by: The FreeBSD Foundation
This probe/attaches correctly in my local branch and now displays
a useful message:
ath0: <Qualcomm Atheros QCA953x> at mem 0x18100000-0x1811ffff irq 0 on nexus0
...
ath0: AR9530 mac 1280.0 RF5110 phy 0.0
active queue scan initiated write.
Re-trying from the inactive queue when doing active scan makes the
loop never end if number of domains is greater than 1 and inactive or
active scan cannot reach the target.
Reported and tested by: Andrew Gallatin <gallatin@netflix.com>
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Some architectures (including ARMv6/v7) do not have separate single step
events and cannot see difference between breakpoint and single step.
Add db_pc_is_singlestep() to avoid skipping instruction we stepped on
to trigger debug event.
This commit does not change the existing functionality but adds possibility
to implement custom db_pc_is_singlestep().
Reviewed by: imp
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4036
- Add a kvaddr_type to represent kernel virtual addresses instead of
unsigned long.
- Add a struct kvm_nlist which is a stripped down version of struct nlist
that uses kvaddr_t for n_value.
- Add a kvm_native() routine that returns true if an open kvm descriptor
is for a native kernel and memory image.
- Add a kvm_open2() function similar to kvm_openfiles(). It drops the
unused 'swapfile' argument and adds a new function pointer argument for
a symbol resolving function. Native kernels still use _fdnlist() from
libc to resolve symbols if a resolver function is not supplied, but cross
kernels require a resolver.
- Add a kvm_nlist2() function similar to kvm_nlist() except that it uses
struct kvm_nlist instead of struct nlist.
- Add a kvm_read2() function similar to kvm_read() except that it uses
kvaddr_t instead of unsigned long for the kernel virtual address.
- Add a new kvm_arch switch of routines needed by a vmcore backend.
Each backend is responsible for implementing kvm_read2() for a given
vmcore format.
- Use libelf to read headers from ELF kernels and cores (except for
powerpc cores).
- Add internal helper routines for the common page offset hash table used
by the minidump backends.
- Port all of the existing kvm backends to implement a kvm_arch switch and
to be cross-friendly by using private constants instead of ones that
vary by platform (e.g. PAGE_SIZE). Static assertions are present when
a given backend is compiled natively to ensure the private constants
match the real ones.
- Enable all of the existing vmcore backends on all platforms. This means
that libkvm on any platform should be able to perform KVA translation
and read data from a vmcore of any platform.
Tested on: amd64, i386, sparc64 (marius)
Differential Revision: https://reviews.freebsd.org/D3341
Previous value was not enough on Arndale platform.
Reviewed by: hselasky
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4145
During cv_wait we may be waiting for an event triggered by callout.
Run callbacks here to avoid code blocking.
Reviewed by: hselasky
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4144
The initial IOCTL implementation supports reading disk physical
geometry.
Two additional functions were added. They allow reading/writing raw
data to the disk (default partition).
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4143
The detach function is called very often, for example from
get_capacity function. We don't want to loose any pointers
here, so disable detaching for umass driver.
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4141
The PA adress must be gathered from an aligned VA,
not the RAW pointer to the memory space.
Reviewed by: hselasky
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4140
If the VPD is corrupt and contains an 'RV' keyword before the
END tag, then this function could return without setting the
return code to report the error.
Found by prefast.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Keep prefast happy by returning the initial queue index
from falconsiena_tx_qcreate(). No change in behaviour, as
etxo_qcreate already zeros *addedp before the call.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
PIO is not yet supported in the FreeBSD driver.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Adjust external port mapping table to distinguish Pavia from Monza.
Now the presence of any 40G mode implies at least 2 outputs per
external port. So Pavia 4x10G ports are now mapped to 1,2,3,4;
Monza 4x10G ports map to 1,1,2,2 as before.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
GCC 4.2.1 used on FreeBSD 8 and 9 branches does not like unnamed
union member in the structure. It is not strictly required in head,
but nice to have to minimize difference with out-of-tree driver.
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
active list, into the header comment for vdrop(), which is the
function that decides whether to leave the vnode on the list. Note
that dirty page write-out in vinactive() is asynchronous.
Discussed with: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
