- Use ustringp for the location of the argv and environment strings
and allow destp to travel further down the stack for the stackgap
and auxv regions.
- Update the Linux copyout_strings variants to move destp down the
stack as was done for the native ABIs in r263349.
- Stop allocating a space for a stack gap in the Linux ABIs. This
used to hold translated system call arguments, but hasn't been used
since r159992.
Reviewed by: kib
Tested on: md64 (amd64, i386, linux64), i386 (i386, linux)
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D22501
the vnode, logical block number, and size of data block that is
being requested. They then use the VOP_BMAP function to calculate
the mapping from logical block number to physical block number from
which to access the data. This change expands the interface to also
pass the physical block number in cases where the VOP_MAP function
may no longer work, for example when a file is being truncated.
No functional change.
Reviewed by: kib
Tested by: Peter Holm
Sponsored by: Netflix
If we boot with hw.ncpu=X (available on arm and arm64 at least) we
shouldn't attach the cpufreq driver as cf_set_method will try to get
the cpuid and it doesn't exists.
This solves cpufreq panicing on RockChip RK3399 when booting with
hw.ncpu=4
MFC after: 1 week
RK3399 PLLs have three modes :
- Normal, where they behave normally and their freq is calculated based on
the registers values.
- Slow, where the PLL freq is 24Mhz (well, the external oscillator).
- Deep Slow, used for suspend where the freq is 32Khz.
We used to put every CPU related PLL in normal mode but it can cause problem
if the firmware didn't setup the clocks register correctly.
And even if it did but left the pll in slow or deep slow mode that might be
because the PMIC suppling voltage for the CPU haven't been configured yet
and we cannot do that at this point.
So remove the ability to set PLLs to normal mode at boot to avoid any problems.
r354247 converted try_include to lfs + dofile with the loader.lua_path added
just before. Fortunately, there was a hardcoded /boot/lua fallback in case
loader.lua_path wasn't being set yet- I typo'd it as loader.lua_paths.
Fix the typo.
X-MFC-With: r354247
MFC after: 3 days
We have a couple optimizations for when the bitset is known to be just
one word. But with dynamically sized bitsets, it was actually more work
to determine the size than just to do the necessary computation. Now,
only use the optimization when the size is known to be constant.
Reviewed by: markj
Discussed with: jeff
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D22639
Maps from the mips busdma dmamap_zone were not completely initialized.
In particular, pagesneeded and pagesreserved were not initialized. This
could cause a crash.
Remove some dead fields from mips struct bus_dmamap while here.
Reported by: brooks
Reviewed by: ian
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D22638
The resizing could be a downsizing so some data would be lost and we
could attempt to read past the end of the new memory allocation.
MFC after: 2 weeks
Sponsored by: Panzura
groups. Do not acquire additional references. This makes the IPv4 IGMP
code in line with the IPv6 MLD code.
Background:
The IPv4 multicast code puts an extra reference on the in_multi struct
when joining groups. This becomes visible when using daemons like
igmpproxy from ports, that multicast entries do not disappear from the
output of ifmcstat(8) when multicast streams are disconnected.
This fixes a regression issue after r349762.
While at it factor the ip_mfilter_insert() and ip6_mfilter_insert() calls
to avoid repeated "is_new" check.
Differential Revision: https://reviews.freebsd.org/D22595
Tested by: Guido van Rooij <guido@gvr.org>
Reviewed by: rgrimes (network)
MFC after: 1 week
Sponsored by: Mellanox Technologies
This was purely automatically massaged... some parts are still imperfect,
but this is close enough to make it more readable/easy to work on.
Unfortunately the vt/syscons/kdb situation slightly complicates changes to
tty locking, so some work will need to be done to remediate that.
tightening constraints on busy as a precursor to lockless page lookup and
should largely be a NOP for these cases.
Reviewed by: alc, kib, markj
Differential Revision: https://reviews.freebsd.org/D22611
the sched_preempt() switch optimization and causes the sched lock to be dropped
and immediately reacquired.
Reviewed by: jhb, kib, mav, markj (with changes)
Differential Revision: https://reviews.freebsd.org/D22623
This makes it possible to retrieve per-connection statistical
information such as the receive window size, RTT, or goodput,
using a newly added TCP_STATS getsockopt(3) option, and extract
them using the stats_voistat_fetch(3) API.
See the net/tcprtt port for an example consumer of this API.
Compared to the existing TCP_INFO system, the main differences
are that this mechanism is easy to extend without breaking ABI,
and provides statistical information instead of raw "snapshots"
of values at a given point in time. stats(3) is more generic
and can be used in both userland and the kernel.
Reviewed by: thj
Tested by: thj
Obtained from: Netflix
Relnotes: yes
Sponsored by: Klara Inc, Netflix
Differential Revision: https://reviews.freebsd.org/D20655
Some of the printf statements only use LF to get a newline. However, a CR character is also required for the serial console to print debug logs in a nice way.
Fix those code locations that only use LF, by adding a CR character.
Reviewed by: markj, aleksandr.fedorov@itglobal.com
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D22552
My changes in 351599 (kindly committed by avg) made the cd(4) media check
asynchronous to avoid a sleep while holding a mutex.
There was a difficult to reproduce bug with those changes that caused a
hang on boot on some single processor machines/VMs. Leandro Lupori
managed to reproduce the bug, diagnose it, and supplied a patch! Here is
his analysis, from the PR:
======
I was able to reproduce the problem described in comment#14.
Actually, I wasn't trying to reproduce it, I just started seeing it a few
weeks ago, in CURRENT.
I can reproduce it consistently, by using QEMU to run a PowerPC64 VM with a
single core/thread (-smp 1).
It happens only when there is no media in the emulated CD-ROM, a device
that QEMU adds by default, unless -nodefaults is specified in command line.
I've debugged it and this is what I've found:
1- After the CD probe is successful, GEOM will try to open the device,
which will end up calling cdcheckmedia(), that sets CD state to
CD_STATE_MEDIA_PREVENT.
2- Next, scsi_prevent() is executed and succeeds, the CD_FLAG_DISC_LOCKED
flag is set and CD state moves to CD_STATE_MEDIA_SIZE.
3- Next, scsi_read_capacity() is executed and fails, state is set to
CD_STATE_MEDIA_ALLOW, cdmediaprobedone() is called and wakes up
cdcheckmedia().
4- Then, when cdstart() is invoked to process CD_STATE_MEDIA_ALLOW, it
first checks if CD_FLAG_DISC_LOCKED is set, and if so skips directly to
CD_STATE_MEDIA_SIZE state. This will repeat the steps of bullet 3, entering
an infinite MEDIA_SIZE command loop.
When there is a least another core/thread, the GEOM thread that performed
the initial cdopen() will get scheduled again, closing the CD device, that
will call cdprevent(PR_ALLOW) that clears the CD_FLAG_DISC_LOCKED flag and
breaks the loop.
So, apparently, the problem is CD_STATE_MEDIA_ALLOW being skipped when
CD_FLAG_DISC_LOCKED is set. If I understand correctly, in this case, the
state should be advanced to CD_STATE_MEDIA size only when the current state
is CD_STATE_MEDIA_PREVENT.
=====
PR: kern/219857
Submitted by: Leandro Lupori <leandro.lupori@gmail.com>
MFC after: 1 week
struct gpio_pin. It turns out these two sets of flags are completely
unrelated to each other.
Also, update the comment for GPIO_ACTIVE_LOW to reflect the fact that it
does get set, somewhat unobviously, by code that parses FDT data. The bits
from the FDT cell containing flags are just copied to gpiobus_pin.flags, so
there's never any obvious reference to the symbol GPIO_ACTIVE_LOW being
stored into the flags field.
After discussing with mmel@, it was clear this is insufficient to address
all the needs. mmel@ will commit his original patch, from
https://reviews.freebsd.org/D13861, and the additions needed from r354714
will be made afterward.
Requested by: mmel
Sponsored by: Juniper Networks, Inc.
When using sysrc to modify a file, the file should be created silently.
However, with the introduction of SVN r335280, an error of "No such file
or directory" would appear despite everything else working as-expected.
The nature of this spurious error is that SVN r335280 did not check if
the file exists first, before trying to fixup the line-endings in the
file just prior to modification.
PR: bin/240875
Reported by: Jose Luis Duran
MFC after: 3 days
FDT bindings document for gpio-i2c devices.
Using the gpio_pin_* functions to acquire/release/manipulate gpio pins
removes the constraint that both gpio pins must belong to the same gpio
controller/bank, and that the gpioiic instance must be a child of gpiobus.
Removing those constraints allows the driver to be fully compatible with
the modern dts bindings for a gpio bitbanged i2c bus.
For hinted attachment, the two gpio pins still must be on the same gpiobus,
and the device instance must be a child of that bus. This preserves
compatibility for existing installations that have use gpioiic(4) with hints.
This lets us print, for example, the user's trap frame when a panic occurs.
The frame address is given in the backtrace at the trap point, which can
then be passed to 'show frame'. This is useful for debugging as it can show
inputs that lead to a panic or fault. It can also be used to print trap
frames from other CPUs that get stuck.
i386 already has a similar command, but no others do.
that they can be used by drivers on non-FDT-configured systems. Only the
functions related to acquiring pins by parsing FDT data remain in
ofw_gpiobus. Also, add two new functions for acquiring gpio pins based on
child device_t and index, or on the bus device_t and pin number. And
finally, defer reserving pins for gpiobus children until they acquire the
pin, rather than reserving them as soon as the child is added (before it's
even known whether the child will attach).
This will allow drivers configured with hints (or any other mechanism) to
use the same code as drivers configured via FDT data. Until now, a hinted
driver and an FDT driver had to be two completely different sets of code,
because hinted drivers could only use gpiobus calls to manipulate pins,
while fdt-configured drivers could not use that API (due to not always being
children of the bus that owns the pins) and had to use the newer
gpio_pin_xxxx() functions. Now drivers can be written in the more
traditional form, where most of the code is shared and only the resource
acquisition code at attachment time changes.
This allows adding more ECN related flags in the future.
No functional change intended.
Submitted by: Richard Scheffenegger
Reviewed by: rrs@, tuexen@
Differential Revision: https://reviews.freebsd.org/D22497
to make them aligned.
Submitted by: Richard Scheffenegger
Reviewed by: rgrimes@, rrs@, tuexen@
Differential Revision: https://reviews.freebsd.org/D22428
As part of my journey to make it easy to determine what's relying on tty
bits, remove a couple more. Some of these just outright didn't need it,
while others did rely on <sys/tty.h> pollution for mutex headers.
The handle value is stable for all shadow objects in the inheritance
chain. This allows to avoid descending the shadow chain to get to the
bottom of it in vm_map_entry_set_vnode_text(), and eliminate
corresponding object relocking which appeared to be contending.
Change vm_object_allocate_anon() and vm_object_shadow() to handle more
of the cred/charge initialization for the new shadow object, in
addition to set up the handle.
Reported by: jeff
Reviewed by: alc (previous version), jeff (previous version)
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differrential revision: https://reviews.freebsd.org/D22541
