It is a preparation to the next patch which will service packet queue even
if packet addtion fails.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2552
Now each branch has one and only one possible TxQ lock state.
It simplifies understanding of the code.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2551
We can't disable it in HW, but we can ignore result.
Discard Rx descriptor checksum flags if Rx checksum offload is off.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2544
was granted via rings and ni_bufs_list_head represented in those rings
and lists (e.g., via SIGKILL), those buffers are no longer available
for subsequent users for the lifetime of the system. To mitigate this
resource leak, reset the allocator state when the last ref to that
allocator is released.
Note that this only recovers leaked resources for an allocator when
there are no longer any users of that allocator, so there remain
circumstances in which leaked allocator resources may not ever be
recovered - consider a set of multiple netmap processes that are all
using the same allocator (say, the global allocator) where members of
that set may be killed and restarted over time but at any given point
there is one member of that set running.
Based on intial work by adrian@.
Reviewed by: Giuseppe Lettieri (g.lettieri@iet.unipi.it), luigi
Approved by: jmallett (mentor)
MFC after: 1 week
Sponsored by: Norse Corp, Inc.
It simplifies understanding of the sfxge_tx_packet_add() logic and
avoids passing of 'locked' to called function.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2547
It is simply not required since the kernel checks corresponding
IFCAP_TSOx capability and CSUM_TSO in hw-assisted offloads.
Note that CSUM_TSO is two bits (CSUM_IP_TSO|CSUM_IP6_TSO) and both bits
are set in IPv4 and IPv6 mbufs.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2546
Also it is cheaper to check Rx descriptor flags than TCP protocol in IP
header.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2542
Netfront has to wait for the backend to switch to state XenbusStateConnected
before sending the ARP request, or else the backend might not be connected
and thus the packet will be lost.
Sponsored by: Citrix Systems R&D
MFC after: 1 week
Tx checksum offload may be enabled/disabled.
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2543
Split IFCAP_HWCSUM to IFCAP_RXCSUM and IFCAP_TXCSUM to highlight Tx and Rx.
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2541
Summary:
The Freescale PCIe Root Complex shows up as a Processor class device, PowerPC
subclass, so the generic PCI code ignores it for a bridge. This adds support
for it.
As part of this, update the Freescale PCI hostbridge driver, to allow probing
beyond the root complex, instead of only allowing "proper" PCI-PCI bridges.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2442
Relnotes: yes
results.
Right now the scan infrastructure assumes the channel is under net80211
control, and that when receiving beacon frames for scanning, the
current channel is indeed what ic_curchan is set to.
But firmware NICs with firmware scan support need more than this -
they can do background scans whilst hiding the off-channel behaviour
from net80211. Ie, net80211 still thinks everything is associated
and on the main channel, but it's getting scan results from all the
background traffic.
However sta_add() pays attention to ic_curchan and discards scan
results that aren't on the right channel. CCK beacon frames can be
decoded from adjacent channels so the receive path and sta_add
discard these as appropriate. This is fine for software scanning
like for ath(4), but not for firmware NICs. So with those, the
whole concept of background firmware scanning won't work without
major hacks (eg, overriding ic_curchan before calling the beacon
input / scan add.)
As part of my scan overhaul, modify sta_add() and the scan_add()
APIs to take an explicit current channel. The normal RX path
will set it to ic_curchan so it's a no-op. However, drivers may
decide to (eventually!) override the scan method to set the
"right" current channel based on what the firmware reports the
scan state is.
So for example, iwn, rsu and other NICs will eventually do this:
* driver issues scan start firmware command;
* firmware sends a "scan start on channel X" notify;
* firmware sends a bunch of beacon RX's as part of
the scan results;
* .. and the driver will replace scan_add() curchan with channel X,
so scan results are correct.
* firmware sends a "scan start on channel Y" notify;
* firmware sends more beacons...
* .. the driver replaces scan_add() curchan with channel Y.
Note:
* Eventually, net80211 should eventually grow the idea of a per-packet
current channel. It's possible in various modes (eg WAVE, P2P, etc)
that individual frames can come in from different channels and that
is under firmware control rather than driver/net80211 control, so
we should support that.
Several improvements to the Synaptics driver to support
semi-multitouch trackpads and some other fixes:
- Two finger scrolling support for "semi-MT" touchpads. Those include
many of the older Synaptics touchpads before "true" multitouch support
(indicated by capMultiFinger). Semi-MT touchpads can report a second
finger position, but the X or Y coordinate may be swapped with some
coordinate of the first finger. This is a result of how the hardware
works internally. Therefore, all that can be reliably extracted is the
bounding box of the two finger positions. Semi-MT touchpads can be
recognized by the capAdvancedGestures capability bit. After setting the
mode byte, advanced gestures mode has to be enabled. Then, data packets
compatible with the capMultiFinger format are sent, so the same two
finger scrolling code can be leveraged. Enabling advanced gestures mode
on true multitouch touchpads should be harmless. Linux seems to always
enable advanced gestures mode.
- Put mode setting logic into own functions synaptics_preferred_mode()
and synaptics_set_mode() to have this in one place.
synaptics_passthrough_on() and synaptics_passthrough_off() currently
always use 0xc1 as the mode byte, which may be wrong for touchpads that
don't have capExtended.
- Expose X and Y resolution of touchpad to userland. Also expose minimum
and maximum X and Y coordinates. This is useful for programs in
userspace that read raw PSM packets (with PSM_LEVEL_NATIVE enabled) and
need to interpret the coordinates.
- Also send "extended w mode" packets (see section 3.2.9 of
511-000275-01_RevB.pdf) to userspace if PSM_LEVEL_NATIVE is enabled.
This is useful for userspace programs/drivers such as
xf86-input-synaptics that can handle these packets.
- Fix parsing of nExtendedQueries, and request extended/continued
capability bits depending on this value.
- capReportsMax, capClearPad, capAdvancedGestures and capCoveredPad must
be extracted from status[0] and not status[2], I think.
Submitted by: Jan Kokemüller jan.kokemueller at gmail.com
bus_alloc_resource(), bus_release_resource() and bus_set_resource()
(bus_generic_rl_alloc_resource(), bus_generic_rl_release_resource() and
bus_generic_rl_set_resource() respectively).
Do not print the resources for nomatch devices.
Use the inherited method for bus_get_resource_list() on ofw_iicbus.c.
Submitted by: jhb and Michal Meloun (D2033)
interacts with interrupts, query ACPI and use MWAIT for entrance into
Cx sleep states. Support C1 "I/O then halt" mode. See Intel'
document 302223-007 "Intelб╝ Processor Vendor-Specific ACPI Interface
Specification" for description.
Move the acpi_cpu_c1() function into x86/cpu_machdep.c and use
it instead of inlining "sti; hlt" sequence in several places.
In the acpi(4) man page, besides documenting the dev.cpu.N.cx_methods
sysctl, correct the names for dev.cpu.N.{cx_usage,cx_lowest,cx_supported}
sysctls.
Both jkim and avg have some other patches implementing the mwait
functionality; this work is unrelated. Linux does not rely on the
ACPI to provide correct tables describing Cx modes. Instead, the
driver has pre-defined knowledge of the CPU models, it was supplied by
Intel.
Tested by: pho (previous versions)
Sponsored by: The FreeBSD Foundation
127 and decrease the maximum number of sub-channels to 1. These
definitions are only used inside the kernel and can be changed later
if more than one sub-channel is desired. This has been done to allow
so-called USB audio rack modules to work with FreeBSD.
Bump the FreeBSD version to force recompiling all external modules.
MFC after: 2 weeks
Reviewed by: mav
and is not applicable unless the integer pointer is NULL. Set it to
zero to avoid confusion. While at it remove extra semicolon at the end
of the "VT_SYSCTL_INT()" macro.
MFC after: 1 week
function. This fixes an issue where X11 keyboard input can appear
stuck. The cause of the problem is a duplicate TTY device window
switch IOCTL during boot, which leaves the "vt_switch_timer" running,
because the current window is already selected. While at it factor out
some NULL checks.
PR: 200032
Differential Revision: https://reviews.freebsd.org/D2480
Reported by: several people
MFC after: 1 week
Reviewed by: emaste
In order to map memory from other domains when running on Xen FreeBSD uses
unused physical memory regions. Until now this memory has been allocated
using bus_alloc_resource, but this is not completely safe as we can end up
using unreclaimed MMIO or ACPI regions.
Fix this by introducing a new newbus method that can be used by Xen drivers
to request for unused memory regions. On amd64 we make sure this memory
comes from regions above 4GB in order to prevent clashes with MMIO/ACPI
regions. On i386 there's nothing we can do, so just fall back to the
previous mechanism.
Sponsored by: Citrix Systems R&D
Tested by: Gustau Pérez <gperez@entel.upc.edu>
1. While disabling interrupt the FW disables interrupts for only 16 vectors.
In case of Invader which supports 96 MSI-x vectors, some spurious interrupts
may come on other vectors even after interrupt disable. So, driver uses a flag
and ignores the spurious interrupts.
2. Reply queue depth is made double the number of commands supported by FW.
3. Misplaced interrupt enable code is now moved down in the OCR path.
4. Updated error handling code in OCR path.
5. Removed un-necessary print.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
issued through the ioctl() interface prior to the kill adapter. This ensures
userspace ioctl() system calls issued just before a kill adapter don't get stuck in
wait state and IOCTLs are returned to application.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
MEGASAS_HBA_OPERATIONAL before getting new RAID map.
There will be a small window where IO will come from OS with old RAID map.
This patch will update adapter state to MEGASAS_HBA_OPERATIONAL,
only after driver has new RAID map to avoid any IOs getting build using old RAID map.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
for two Drive Raid-1 configuration only.
Now, Driver support fast path read load balancing for all (any number of disk) Raid-1 configuration.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
FW expose Secure Jbod support via Controller properity.
Firmware expect IOs to be received from different IO path than
conventional fast path queue, in case of SED drives.
To have Secure jbod support user need driver and firmware support.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
