standard kill(). On other systems, SI_LWP is generated by lwp_kill().
This will allow conforming applications to differentiate between
signals generated by standard events and those generated by other
implementation events in a manner compatible with existing practice.
- Bump __FreeBSD_version
support WOL. Some controllers require additional 3-wire auxiliary
remote wakeup connector to draw power. More recent xl(4)
controllers may not need the wakeup connector though.
initialize controller from a known good state. Previously driver
used to issue controller reset while TX/RX DMA are in progress.
I guess resetting controller in active TX/RX DMA cycle is to ensure
stopping I/Os in xl_shutdown(). I remember some buggy controllers
didn't respond with stop command if controller is under high
network load at the time of shutdown so resetting controller was
the only safe way to stop the I/Os. However, from my experiments,
controller always responded with stop command under high network
load so I think it's okay to remove the xl_reset() in
device_shutdown handler.
Resetting controller also will clear configured RX filter which
in turn will make WOL support hard because driver have to reprogram
RX filter in WOL handler as well as setting station address.
Use MACHINE_CPUARCH in preference to MACHINE_ARCH. The former is the
source code location of the machine, the latter the binary output. In
general, we want to use MACHINE_CPUARCH instead of MACHINE_ARCH unless
we're tesitng for a specific target. The isn't even moot for
i386/amd64 where there's momemntum towards a MACHINE_CPUARCH == x86,
although a specific cleanup for that likely would be needed...
the uio_offset adjustment instead to calculate a correct *len.
Without this change, we run off the end of the directory data
we're reading and panic horribly for nfs filesystems.
MFC after: 1 week
register mapping. I'm not sure whether it comes from the fact that
controllers live behind certain PCI brdge(PLX PCI 6152 33BC) and
the bridge has some issues in handling I/O space register mapping.
Unfortunately it's not possible to narrow down to an exact
controller that shows this issue because RealTek used the same PCI
device/revision id again. In theory, it's possible to check parent
PCI bridge device and change rl(4) to use memory space register
mapping if the parent PCI bridge is PLX PCI 6152. But I didn't try
to do that and we wouldn't get much benefit with added complexity.
Blindly switching to use memory space register mapping for rl(4)
may make most old controllers not to work. At least, I don't want
to take potential risk from such change. So use I/O space register
mapping by default but give users chance to override it via a
tunable. The tunable to use memory space register mapping would be
given by adding the following line to /boot/loader.conf file.
dev.rl.%d.prefer_iomap="0"
This change makes P811B quad-port work with this tunable.
Tested by: Nikola Kalpazanov ( n.kalpazanov <> gmail dot com )
MFC after: 1 week
devfs_populate(). This is a prerequisite for the automatic removal of
empty directories which will be committed in the future.
Reviewed by: kib (previous version)
Sponsored by: The FreeBSD Foundation
> Description of fields to fill in above: 76 columns --|
> PR: If a GNATS PR is affected by the change.
> Submitted by: If someone else sent in the change.
> Reviewed by: If someone else reviewed your modification.
> Approved by: If you needed approval for this commit.
> Obtained from: If the change is from a third party.
> MFC after: N [day[s]|week[s]|month[s]]. Request a reminder email.
> Security: Vulnerability reference (one per line) or description.
> Empty fields above will be automatically removed.
M sys/fasttrap_impl.h
use '-' in probe names, matching the probe names in Solaris.[1]
Add userland SDT probes definitions to sys/sdt.h.
Sponsored by: The FreeBSD Foundation
Discussed with: rwaston [1]
Right now unionfs only allows filesystems to be mounted on top of
another if it supports whiteouts. Even though I have sent a patch to
daichi@ to let unionfs work without it, we'd better also add support for
whiteouts to tmpfs.
This patch implements .vop_whiteout and makes necessary changes to
lookup() and readdir() to take them into account. We must also make sure
that when adding or removing a file, we honour the componentname's
DOWHITEOUT and ISWHITEOUT, to prevent duplicate filenames.
MFC after: 1 month
datagrams with checksum value 0 when TX UDP checksum offloading is
enabled. Generating UDP checksum value 0 is RFC 768 violation.
Even though the probability of generating such UDP datagrams is
low, I don't want to see FreeBSD boxes to inject such datagrams
into network so disable UDP checksum offloading by default. Users
still override this behavior by setting a sysctl variable or loader
tunable, dev.bge.%d.forced_udpcsum.
I have no idea why this issue was not reported so far given that
bge(4) is one of the most commonly used controller on high-end
server class systems. Thanks to andre@ who passed the PR to me.
PR: kern/104826
problems compiling it, but it just gets too big at the moment, even
with -Os. This is not applicable to gptboot, though.
Submitted by: Dimitry Andric <dimitry at andric.com>
LK_CANRECURSE after a lock is created. Use them to implement macros that
otherwise manipulated the flags directly. Assert that the associated
lockmgr lock is exclusively locked by the current thread when manipulating
these flags to ensure the flag updates are safe. This last change required
some minor shuffling in a few filesystems to exclusively lock a brand new
vnode slightly earlier.
Reviewed by: kib
MFC after: 3 days
of p_traceflag that is stored in the kinfo_proc structure. It is still
racey even with the lock and the code will read a consistent snapshot of
the flag without the lock.
* Add a function to write to the relevant PLL register
* Break out the PLL configuration for the AR71XX into the CPU ops,
lifted from if_arge.c.
* Add the AR91XX PLL configuration ops, using the AR91XX register
definitions.
This is untested but should at least allow an AR724X to boot.
The current code is lacking the detail needed to expose the PCIe bus.
It is also lacking any NIC, PLL or flush/WB code.
This works well enough to bring a system up to single-user mode
using an MDROOT.
Known Issues:
* The EHCI USB doesn't currently work and will panic the kernel during
attach.
* The onboard ethernet won't work until the PLL routines have been
fleshed out and shoe-horned into if_arge.
* The WMAC device glue (and quite likely the if_ath support)
hasn't yet been implemented.
Add kernel side support for Secure Neighbor Discovery (SeND), RFC 3971.
The implementation consists of a kernel module that gets packets from
the nd6 code, sends them to user space on a dedicated socket and reinjects
them back for further processing.
Hooks are used from nd6 code paths to divert relevant packets to the
send implementation for processing in user space. The hooks are only
triggered if the send module is loaded. In case no user space
application is connected to the send socket, processing continues
normaly as if the module would not be loaded. Unloading the module
is not possible at this time due to missing nd6 locking.
The native SeND socket is similar to a raw IPv6 socket but with its own,
internal pseudo-protocol.
Approved by: bz (mentor)
* Implement a SoC probe function, from Linux, which determines the
SoC family, type and revision. This only probes the AR71xx series
SoC and (currently) panics on others.
* Migrate some of the AR71XX specific hardware init (USB device, determining
system frequencies) into using the cpuops introduced in an earlier commit.
Other SoC specific hardware stuff (per-device flush/WB, GPIO pin wiring,
Ethernet PLL setup, other things I've likely missed) will be introduced in
subsequent commits.
Reviewed by: imp@
Obtained from: (partially) Linux
it must reset its congestion window back to the initial window.
RFC3390 has increased the initial window from 1 segment to up to
4 segments.
The initial window increase of RFC3390 wasn't reflected into the
restart window which remained at its original defaults of 4 segments
for local and 1 segment for all other connections. Both values are
controllable through sysctl net.inet.tcp.local_slowstart_flightsize
and net.inet.tcp.slowstart_flightsize.
The increase helps TCP's slow start algorithm to open up the congestion
window much faster.
Reviewed by: lstewart
MFC after: 1 week
sysctl's and remove any side effects.
Both sysctl's share the same backend infrastructure and due to the
way it was implemented enabling net.inet.tcp.log_in_vain would also
cause log_debug output to be generated. This was surprising and
eventually annoying to the user.
The log output backend is kept the same but a little shim is inserted
to properly separate log_in_vain and log_debug and to remove any side
effects.
PR: kern/137317
MFC after: 1 week
1. On n64, use XKPHYS to map page table pages instead of KSEG0. Maintain
just one freepages list on n64.
The changes are mainly to introduce MIPS_PHYS_TO_DIRECT(pa),
MIPS_DIRECT_TO_PHYS(), which will use KSEG0 in 32 bit compilation
and XKPHYS in 64 bit compilation.
2. Change macro based PMAP_LMEM_MAP1(), PMAP_LMEM_MAP2(), PMAP_LMEM_UNMAP()
to inline functions.
3. Introduce MIPS_DIRECT_MAPPABLE(pa), which will further reduce the cases
in which we will need to have a special case for 64 bit compilation.
4. Update CP0 hazard definitions for CPU_RMI - the cpu does not need any
nops
Reviewed by: neel
number of syncache entries into account for the surplus we add to account
for a possible increase of records in the re-entry window.
Discussed with: jhb, silby
MFC after: 1 week
Each of these SoCs have different devices, different hardware initialisation
methods and, quite likely, different quirks. These functions will abstract
out the SoC differences and keep these differences out of the drivers (eg
USB init, if_arge, etc.)
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
memory size estimate to userland for pcb list sysctls. The previous
behavior of a "slop" of n/8 does not work well for small values of n
(e.g. no slop at all if you have less than 8 open UDP connections).
Reviewed by: bz
MFC after: 1 week
method is used by the PCI bus driver to query the power management system
to determine the proper device state to be used for a device during suspend
and resume. For the ACPI PCI bridge drivers this calls
acpi_device_pwr_for_sleep(). This removes ACPI-specific knowledge from
the PCI and PCI-PCI bridge drivers.
Reviewed by: jkim
In particular, provide pagesize and pagesizes array, the canary value
for SSP use, number of host CPUs and osreldate.
Tested by: marius (sparc64)
MFC after: 1 month
to uma_zone_set_max().
The UMA zone limit is not exactly set to the value supplied but
rounded up to completely fill the backing store increment (a page
normally). This can lead to surprising situations where the number
of elements allocated from UMA is higher than the supplied limit
value. The new get function reads back the effective value so that
the supplied limit value can be adjusted to the real limit.
Reviewed by: jeffr
MFC after: 1 week
path MTU discovery and the tcp_minmss limiter for very small MTU's.
When the MTU suggested by the gateway via ICMP, or if there isn't
any the next smaller step from ip_next_mtu(), is lower than the
floor enforced by net.inet.tcp.minmss (default 216) the value is
ignored and the default MSS (512) is used instead. However the
DF flag in the IP header is still set in tcp_output() preventing
fragmentation by the gateway.
Fix this by using tcp_minmss as the MSS and clear the DF flag if
the suggested MTU is too low. This turns off path MTU dissovery
for the remainder of the session and allows fragmentation to be
done by the gateway.
Only MTU's smaller than 256 are affected. The smallest official
MTU specified is for AX.25 packet radio at 256 octets.
PR: kern/146628
Tested by: Matthew Luckie <mjl-at-luckie org nz>
MFC after: 1 week
report when a new socket couldn't be created because one of
in_pcbinshash(), in6_pcbconnect() or in_pcbconnect() failed.
Logging is conditional on net.inet.tcp.log_debug being enabled.
MFC after: 1 week
and we loop back to 'again'. If the remainder is less or equal
to one full segment, the TSO flag was not cleared even though
it isn't necessary anymore. Enabling the TSO flag on a segment
that doesn't require any offloaded segmentation by the NIC may
cause confusion in the driver or hardware.
Reset the internal tso flag in tcp_output() on every iteration
of sendalot.
PR: kern/132832
Submitted by: Renaud Lienhart <renaud-at-vmware com>
MFC after: 1 week
a kernel printf to a log output with the priority of LOG_NOTICE.
This way the messages still show up in /var/log/messages but no
longer spam the console every other second on busy servers that
are port scanned:
"Limiting open port RST response from 114 to 100 packets/sec"
PR: kern/147352
Submitted by: Eugene Grosbein <eugen-at-eg sd rdtc ru>
MFC after: 1 week
It was experimental and interferes with the normal congestion control
algorithms by instating a separate, possibly lower, ceiling for the
amount of data that is in flight to the remote host. With high speed
internet connections the inflight limit frequently has been estimated
too low due to the noisy nature of the RTT measurements.
This code gives way for the upcoming pluggable congestion control
framework. It is the task of the congestion control algorithm to
set the congestion window and amount of inflight data without external
interference.
Reviewed by: lstewart
MFC after: 1 week
Removal after: 1 month
and go to the next iteration early if multicast filtering would decide that
this socket shall not receive the data.
Unlock the pcb in that case or we leak the read lock and next time trying
to get a write lock, would hang forever.
PR: kern/149608
Submitted by: Chris Luke (chrisy flirble.org)
MFC after: 3 days
It is more appropriate in this context because TSC MSR is reset to zero
when the CPU is restarted from S3 and above. Move acpi_resync_clock() back
to where it was before r211202. It does not make a difference any more.
Interrupt driven configuration hooks serve two purposes: they are a
mechanism for registering for a callback that is invoked once interrupt
services are available, and they hold off root device selection so long
as any configuration hooks are still active. Before this change, it was
not possible to safely register additional hooks from the context of a
configuration hook callback. The need for this feature arises when
interrupts are required to discover new devices (e.g. access to the XenStore
to find para-virtualized devices) which in turn also require the ability
to hold off root device selection until some lengthy, interrupt driven,
configuration task has completed (e.g. Xen front/back device driver
negotiation).
More specifically, the mutex protecting the list of active configuration
hooks is never held during a callback, and static information is used
to ensure proper ordering and only a single callback to each hook even
when faced with registration or removal of a hook during an active run.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week.
time-of-day clock or vice versa. For x86 systems, RTC resolution is one
second and we used to lose up to one second whenever we initialize system
time from RTC or write system time back to RTC. With this change, margin
of error per conversion is roughly between -0.5 and +0.5 second rather
than between -1 and 0 second. Note that it does not take care of errors
from getnanotime(9) (which is up to 1/hz second) or CLOCK_GETTIME() latency.
These are just too expensive to correct and it is not worthy of the cost.
case future compile-time knobs were added that it wants to use.
Also add include guards and forward declarations to vm/memguard.h.
Approved by: zml (mentor)
MFC after: 1 month
if the device file appears during or after the link creation.
User created symbolic links are now inserted at the head of the
directory entry list after the "." and ".." entries. A new directory
entry flag DE_COVERED indicates that an entry is covered by a symbolic
link.
PR: kern/114057
Reviewed by: kib
Idea from: kib
Discussed on: freebsd-current (mostly silence)
As long as interrupts are disabled and there is not explicit call to
sched_add() there can't be any preemption there, thus the calls may be
consistent.
Reported by: kib, jhb
- Enable KX and UX bits on CPU startup for non-boot CPUs
- Keep the KX bit when in userspace - XTLB handler needs it to access
PCPU data
- revert r210638 partly - we don't need to enable KX on kernel entry
now
Reviewed by: jmallett, imp
1. Move dirty bit emulation code that is duplicted for kernel and user
in trap.c to a function pmap_emulate_modified() in pmap.c.
2. While doing dirty bit emulation, it is not necessary to update the
TLB entry on all CPUs using smp_rendezvous(), we can just update the
TLB entry on the current CPU, and let the other CPUs update their TLB
entry lazily if they get an exception.
Reviewed by: alc, neel
per-cpu variants are also available to be called. The per-cpu variants
are needed for some later optimizations.
Also remove unnecessary casts, do some style fixes.
Reviewed by: alc, neel
bufobj lock. If b_bufobj is not NULL, then bufobj lock should be
held when manipulating the flags. Not doing this sometimes leaves
BV_BKGRDINPROG to be erronously set, causing softdep' getdirtybuf() to
stuck indefinitely in "getbuf" sleep, waiting for background write to
finish which is not actually performed.
Add BO_LOCK() in the cases where it was missed.
In collaboration with: pho
Tested by: bz
Reviewed by: jeff
MFC after: 1 month
the worklist (in softdep_process_journal), but also after flushing the
workitems. Might be, we should even do this before bwillwrite() too, but
this seems to be not needed for now.
Fs might be suspended during processing the queue, and then there is
nobody around to unsuspend.
In collaboration with: pho
Tested by: bz
Reviewed by: jeff
If it does, don't then try reprogramming the NF "cap" values (ie
what values are the "maximum" value the NF can be) - instead,
just leave the current CCA value as the NF cap.
This was inspired by some similar work from ath9k. It isn't
a 100% complete solution (as there may be some reason where a
high NF CCA/cap is written, causing the baseband to stop thinking it
is able to transmit, leading to stuck beacon and interface reset)
which I'll investigate and look at fixing in a later commit.
Obtained from: Linux
AR5416 and later chipsets.
ath_hal_calibrateN() calls the HAL calibrateN function with rxchainmask=0x1.
This is not necessarily the case for AR5416 and later chipsets.
use-after-free over a longer time. Also release the backing pages of
a guarded allocation at free(9) time to reduce the overhead of using
memguard(9). Allow setting and varying the malloc type at run-time.
Add knobs to allow:
- randomly guarding memory
- adding un-backed KVA guard pages to detect underflow and overflow
- a lower limit on the size of allocations that are guarded
Reviewed by: alc
Reviewed by: brueffer, Ulrich Spörlein <uqs spoerlein net> (man page)
Silence from: -arch
Approved by: zml (mentor)
MFC after: 1 month
are served via an interrupt gate.
However, that doesn't explicitly prevent preemption and thread
migration thus scheduler pinning may be necessary in some handlers.
Fix that.
Tested by: gianni
MFC after: 1 month
r211130 in favor of this more general fix.
This fixes a compilation error for mips 64-bit little endian build.
libexec/rtld-elf/mips/reloc.c:196: warning: right shift count >= width of type
Suggested by: stefanf, jchandra, bde
bridge(4), lagg(4) etc. and make use of function pointers and
pf_proto_register() to hook carp into the network stack.
Currently, because of the uncertainty about whether the unload path is free
of race condition panics, unloads are disallowed by default. Compiling with
CARPMOD_CAN_UNLOAD in CFLAGS removes this anti foot shooting measure.
This commit requires IP6PROTOSPACER, introduced in r211115.
Reviewed by: bz, simon
Approved by: ken (mentor)
MFC after: 2 weeks
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
While there, also fix some places assuming cpu type is 'int' while
u_int is really meant.
Note: this will also fix some possible races in per-cpu data accessings
to be addressed in further commits.
In collabouration with: Yahoo! Incorporated (via sbruno and peter)
Tested by: gianni
MFC after: 1 month
flag immediately so it's only set once per longcal interval.
Without this, the current AR5416 code will continuously spam NF
calibrations during a periodic calibration if the longcal flag
is set. The longcal flag wouldn't be cleared until the calibration
method indicates that calibrations are "complete".
This drops the rate of NF calibration updates down from "once every
shortcal" (ie, every 100ms) during a periodic calibration, to only
once per "longcal" interval. Spamming NF calibrations every 100ms
caused some potentially horrific issues in noisy environments as
NF calibrations can take longer than 100ms and this spamming can
cause invalid NF calibration results to be read back - leading to
missed beacons, and thus leading to a stuck beacon situation.
Stuck beacons cause interface resets, which restart calibrations.
This means that the longcal calibration runs every 100ms (shortcal)
until all initial calibrations are completed. This spamming can then
cause the above issues which leads to stuck beacons, leading to
interface resets, etc, etc. Quite annoying.
Now we use a regular mutex instead of a spin mutex. When we enter and exit
the emulator, spinlock_enter() and spinlock_exit() are additionally used.
Move some page table related stuff from x86bios_init() and x86bios_uninit()
to x86bios_map_mem() and x86bios_unmap_mem().
most system, based on benchmark results on a low-end fibre channel SAN
under VMWare:
vfs.read_max read performance
8 (historical default) 83 MB/s
16 (recent bump) 131 MB/s
32 (this version) 152 MB/s
64 157 MB/s
(results are +/- 3 MB/s)
As read-ahead is heuristic, based on past IO requests, it shouldn't be
problematic. The new default is still smaller then in other OSes.
Add proto spacers to inet6sw like we have for legacy IP. This allows us
to dynamically pf_proto_register() for INET6 from modules, needed by
upcoming CARP changes and SeND.
MC and SCTP could make use of it as well in theory in the future after
upcoming VIMAGE vnet teardown work.
Discussed with: will, anchie
MFC after: 10 days
Even though cons25 normally doesn't support origin regions, this
emulator does allow you to do it. It makes more sense to blank only the
origin region when emitting ^L instead of blanking the entire screen.
Apart from that, we should always place the cursor inside the origin
region, which doesn't happen right now.
within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
controller. These controllers are known as L1D(AR8151) and
L2CB/B2(AR8152). This change adds supports for the following
controllers.
o AR8151 v1.0(L1D) gigabit ethernet controller
o AR8151 v2.0(L1D) gigabit ethernet controller
o AR8152 v1.1(L2CB) fast ethernet controller
o AR8152 v2.0(L2CB2) fast ethernet controller
These controllers have the same feature of AR8131/AR8132 and
support improved power saving control. The user visible change at
this moment is reduced jumbo frame size from 9KB to 6KB. Many
thanks to Atheros for continuing to support FreeBSD.
HW donated by: Atheros Communications, Inc.
- Increase target limit from 4 to 64; this limit will be removed entirely
at a later time.
- Improve recovery from lost network connections.
- Fix some potential deadlocks and a serious memory leak.
- Fix incorrect use of MH_ALIGN (instead of M_ALIGN), which makes no
practical difference, but triggers a KASSERT with INVARIANTS.
- Fix some warnings in iscontrol(8) and improve the man page somewhat.
Submitted by: Daniel Braniss <danny@cs.huji.ac.il>
Sponsored by: Dansk Scanning A/S, Data Robotics Inc.
This fixes booting from a ZFS mirror with a unavailable primary device.
PR: kern/148655
Reviewed by: avg
Approved by: delphij (mentor)
MFC after: 3 days
like memory mapped register access. Typical problem from the issue
was MII access returned unreliable values. I'm not sure this comes
from lack of register flushing in MII access after accessing
STE_PHYCTL register though.
To address the issue, read hints data that controls which type of
memory mapping should be used in driver. ste(4) still prefers
memory mapping to io mapping but honor hints entered by user except
for controllers that have problems with memory mapping.
The hint to use iomapping could be given by adding the following
line to /boot/device.hints file.
hint.ste.0.prefer_iomap="1"
PR: kern/149285
MFC after: 5 days
number of CPUs detection.
However, that was not mention at all, the problem was not reported, the
patch has not been MFCed and the fix is mostly improper.
Fix the original overflow (caused when 32 CPUs must be detected) by
just using a different mathematical computation (it also makes more
explicit the size of operands involved, which is good in the moment
waiting for a more complete support for a large number of CPUs).
PR: kern/148698
Submitted by: Joe Landers <jlanders at vmware dot com>
Tested by: gianni
MFC after: 10 days
td_critnest > 1 when not already running on the desired CPU read the
TICK counter of the BSP via a direct cross trap request in that case
instead.
- Treat the STICK based timecounter the same way as the TICK based one
regarding its quality and obtaining the counter value from the BSP.
Like the TICK timers the STICK ones also are only synchronized during
their startup (which might not result in good synchronicity in the
first place) but not afterwards and might drift over time, causing
problems when the time is read from different CPUs (see r135972).
interface goes to issue LINK_UP, then LINK_DOWN, then LINK_UP at
cold boot. This behavior is not observed when carp(4) interface
is created slightly later, when the underlying interface is fully
up.
Before this change what happen at boot is roughly:
- ifconfig creates em0 interface;
- ifconfig clones a carp device using em0;
(em0's link state is DOWN at this point)
- carp state: INIT -> BACKUP [*]
- carp state: BACKUP -> MASTER
- [Some negotiate between em0 and switch]
- em0 kicks up link state change event
(em0's link state is now up DOWN at this point)
- do_link_state_change() -> carp_carpdev_state()
- carp state: MASTER -> INIT (via carp_set_state(sc, INIT)) [+]
- carp state: INIT -> BACKUP
- carp state: BACKUP -> MASTER
At the [*] stage, em0 did not received any broadcast message from other
node, and assume our node is the master, thus carp(4) sets the link
state to "UP" after becoming a master. At [+], the master status
is forcely set to "INIT", then an election is casted, after which our
node would actually become a master.
We believe that at the [*] stage, the master status should remain as
"INIT" since the underlying parent interface's link state is not up.
Obtained from: iXsystems, Inc.
Reported by: jpaetzel
MFC after: 2 months
suspend state. Also disable master clock after PHY power down,
this is supposed to save more power. The master clock should be
enabled if WOL is active.
to single CPUs more efficiently with Cheetah(-class) and Jalapeno CPUs.
Besides being used to implement the ipi_cpu() introduced in r210939,
cpu_ipi_single() will also be used internally by the sparc64 MD code.
- Factor out the Jalapeno support from the Cheetah IPI send functions
in order to be able to more easily and efficiently implement support
for more than 32 target CPUs as well as a workaround for Cheetah+
erratum 25 for the latter.
the vfs.read_max default. For most systems this means going from 128 KiB
to 256 KiB, which is still very conservative and lower than what most
other operating systems use, but as a sane default should not
interfere much with existing systems.
For systems with RAID volumes and/or virtualization envirnments, where
read performance is very important, increasing this sysctl tunable to 32
or even more will demonstratively yield additional performance benefits.
If MAXPHYS ever gets bumped up, it will probably be a good idea to slave
read_max to it.
SOCK_DGRAM socket. MSG_TRUNC was only returned when some mbufs could
not be copied to the application. If some data was left in the last
mbuf, it was correctly discarded, but MSG_TRUNC was not set.
Reviewed by: bz
MFC after: 3 weeks
and BeOS. The devices supported by uslcom(4) are now in sync with:
NetBSD src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Two vendor/product IDs from Linux have not been added to uslcom(4):
SILABS SAEL - This device has special code in u3g to support it
SILABS GSM2228 - I suspect this should also be covered by u3g(4).
MFC after: 1 week
vendor ID in the vendor section, and by symbolic name in the product
section. Products are sorted by product ID. While here, get rid of a
duplicate Microsoft Mouse entry, revealed by sorting.
MFC after: 1 week
1. Use unsigned rather than signed lengths
2. Bound messages to/from Venus to VC_MAXMSGSIZE
3. Bound messages to/from general user processes to VC_MAXDATASIZE
4. Update comment regarding data limits for pioctl
Without (1) and (3), it may be possible for unprivileged user processes to
read sensitive portions of kernel memory. This issue is only present if
the Coda kernel module is loaded and venus (the userspace Coda daemon) is
running and has /coda mounted.
As Coda is considered experimental and production use is warned against in
the coda(4) man page, and because Coda must be explicitly configured for a
configuration to be vulnerable, we won't be issuing a security advisory.
However, if you are using Coda, then you are advised to apply these fixes.
Reported by: Dan J. Rosenberg <drosenberg at vsecurity.com>
Obtained from: NetBSD (Christos Zoulas)
Security: Kernel memory disclosure; no advisory as feature experimental
MFC after: 3 days
IPI to a specific CPU by its cpuid. Replace calls to ipi_selected() that
constructed a mask for a single CPU with calls to ipi_cpu() instead. This
will matter more in the future when we transition from cpumask_t to
cpuset_t for CPU masks in which case building a CPU mask is more expensive.
Submitted by: peter, sbruno
Reviewed by: rookie
Obtained from: Yahoo! (x86)
MFC after: 1 month
interfaces to be a vlan (IFT_L2VLAN) rather than an Ethernet interface
(IFT_ETHER). The code already fixed if_type in the ifnet causing some
places to report the interface as a vlan (e.g. arp -a output) and other
places to report the interface as Ethernet (getifaddrs(3)). Now they
should all report IFT_L2VLAN.
Reviewed by: brooks
MFC after: 1 month
the virtualization detection successfully disabling the clflush instruction.
This fixes insta-panics for XEN hvm users when the hw.clflush_disable
tunable is -1 or 0 (-1 by default).
Discussed with: jhb
cdev will never be destroyed. Propagate the flag to devfs vnodes as
VV_ETERNVALDEV. Use the flags to avoid acquiring devmtx and taking a
thread reference on such nodes.
In collaboration with: pho
MFC after: 1 month
MIPS doesn't really need to use atomic_cmpset_int() in situations like
this because the software dirty bit emulation in trap.c acquires
the pmap lock. Atomics like this appear to be a carryover from i386
where the hardware-managed TLB might concurrently set the modified bit.
Reviewed by: alc
pmap_page_wired_mappings() counts the number of pv entries for the
specified page that have the pv entry wired flag set to TRUE.
pmap_enter() correctly initializes this flag. However,
pmap_change_wiring() doesn't update the corresponding pv entry flag,
only the PTE. So, the count returned by pmap_page_wired_mappings()
will sometimes be wrong.
In the short term, the best fix would be to eliminate the pv entry
flag and use only the PTE. That flag is wasting non-trivial memory.
Remove pv_wired flag, and use PTE flag to count the wired mappings.
Reviewed by: alc
value resulted in poor performance for UDP packets. With this
change, UDP bulk transfer performance is more than 940Mbps.
While I'm here fix a wrong register definition.
VM86 calls instead of the real mode emulator as a backend. VM86 has been
proven reliable for very long time and it is actually few times faster than
emulation. Increase maximum number of page table entries per VM86 context
from 3 to 8 pages. It was (ridiculously) low and insufficient for new VM86
backend, which shares one context globally. Slighly rearrange and clean up
the emulator backend to accommodate new code. The only visible change here
is stack size, which is decreased from 64K to 4K bytes to sync. with VM86.
Actually, it seems there is no need for big stack in real mode.
MFC after: 1 month
As des noted, the section on SCTP would benefit from
a rewrite by a native speaker (which I am not).
Any volunteers?
Approved by: des (mentor)
MFC after: 1 week
bus_generic_resume() since the pci_link(4) driver was added.
- Change the ACPI PCI-PCI bridge driver to inherit most of its methods
from the generic PCI-PCI bridge driver. In particular, this will now
restore PCI config registers for ACPI PCI-PCI bridges.
Tested by: Oleg Sharoyko osharoiko of gmail
'counter_upper' and 'counter_lower_last'. The race exists because
interrupts are enabled even though tick_ticker() executes in a
critical section.
Fix a bug in clock_intr() in how it updates the cached values of
'counter_upper' and 'counter_lower_last'. They are updated only
when the COUNT register rolls over. More interestingly it will *never*
update the cached values if 'counter_lower_last' happens to be zero.
Get rid of superfluous critical section in clock_intr(). There is no
reason to do this because clock_intr() executes in hard interrupt
context.
Switch back to using 'tick_ticker()' as the cpu ticker for Sibyte.
Reviewed by: jmallett, mav
