VR_STICKHW register would result in unexpected results on these
hardwares. wpaul said the following for the issue.
The vr_attach() routine unconditionally does this for all supported
chips:
/*
* Windows may put the chip in suspend mode when it
* shuts down. Be sure to kick it in the head to wake it
* up again.
*/
VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1));
The problem is, the VR_STICKHW register is not valid on all Rhine
devices. The VT86C100A chip, which is present on the D-Link DFE-530TX
boards, doesn't support power management, and its register space is
only 128 bytes wide. The VR_STICKHW register offset falls outside this
range. This may go unnoticed in most scenarios, but if you happen to have
another PCI device in your system which is assigned the register
space immediately after that of the Rhine, the vr(4) driver will
incorrectly stomp it. In my case, the BIOS on my test board decided
to put the register space for my PRO/100 ethernet board right next
to the Rhine, and the Rhine driver ended up clobbering the IMR register
of the PRO/100 device. (Long story short: the board kept locking up on
boot. Took me the better part of the morning suss out why.)
The strictly correct thing to do would be to check the PCI config space
to make sure the device supports the power management capability and only
write to the VR_STICKHW register if it does.
Instead of inspecting chip revision numbers for the availability of
VR_STICKHW register, check the existence of power management capability
of the hardware as wpaul suggested.
Reported by: wpaul
Suggested by: wpaul
OK'ed by: jhb
1. The locking was changed to shared but roundrobin mode still updated a
pointer in the softc with the next tx interface to use. This will panic
under high load. Change this to an atomically incremented sequence number in
order to choose the tx port in round robin.
2. IFQ_HANDOFF will free the mbuf if the queue is full, this will then be freed
again by lagg_start() and panic. Reorganised the error handling and freeing
to fix this.
MFC after: 3 days
- Mention tzdata2007h update. An in advance &merged; is
added so that we don't have to change this again when
it is actually MFC'ed.
Approved by: re (bmah)
SAS-enabled cards. It also makes the driver MPSAFE, eliminating some
problems that resulted from CAM becoming MPSAFE. Many thanks to 3Ware/AMCC
for continuing to support FreeBSD.
Submitted by: Manjunath Ranganathaiah
Approved by: re
voltage of 0. This can result in a divide by zero trap. Add a guard
for this case. The value of lfcap is checked in acpi_battery_bif_valid()
just before this, so it is safe.
Reportd by: sam
Approved by: re
MFC after: 3 days
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
local rc.d scripts in the overall boot order was added.
Proper rc.d scripts are run by rc.subr in a subshell, whereas scripts that
end in .sh are sourced into rc's shell. The latter has potential to create
serious boot problems, and there is no reason that the same functionality
cannot be added by the user in the form of a proper rc.d script (as
opposed to being added by the user in the form of /etc/rc.early).
This script will be removed prior to the 8.0 branch.
Approved by: re (kensmith)
for pre-5.0 variable names.
Remove two dhcp compatibility variables added after the 5.1-RELEASE.
Remove the now-unused support for these shims.
Approved by: re (kensmith)
fixes a bug on UP machines with SMP kernels where the idle thread
constantly switches after trying to steal work from the local cpu.
- Make the idle stealing code more robust against self selection.
- Prefer to steal from the cpu with the highest load that has at least one
transferable thread. Before we selected the cpu with the highest
transferable count which excludes bound threads.
Collaborated with: csjp
Approved by: re
to simply switch rather than lowering priority and switching. This allows
threads of equal priority to run but not lesser priority.
Discussed with: davidxu
Reported by: NIIMI Satoshi <sa2c@sa2c.net>
Approved by: re
critical_exit() owepreempt check. ULE will always use owepreempt to
preempt the idle thread. This change does not effect 4BSD since it will
never set owepreempt without PREEMPTION enabled.
- Remove some unused code from choosethread().
Discussed with: jhb
Approved by: re
Timezone data changes in the following locations:
- Egypt (push possible DST ending one year ahead)
- Iran gets DST again in 2008.
- Palestine DST time for this year fixed.
- Brasils DST rule change in 2008.
- Venezuela time moves half an hour back at the end of this year.
PR: conf/116900
Approved by: re (Ken Smith), grog@ (mentor)
MFC after: 1 week
support for these. This is in line with gnu/lib/libgomp/config.h and
gnu/lib/libstdc++/config.h.
Reviewed by: cognet, obrien
Approved by: re (kensmith)
it must first ensure that the page is no longer mapped. This is
trivially accomplished by calling pmap_remove_all() a little earlier
in vm_page_cache(). While I'm in the neighborbood, make a related
panic message a little more useful.
Approved by: re (kensmith)
Reported by: Peter Holm and Konstantin Belousov
Reviewed by: Konstantin Belousov
a consequence of sparc64/sparc64/vm_machdep.c revision 1.76. It occurs
when uma_small_free() frees a page. The solution has two parts: (1) Mark
pages allocated with VM_ALLOC_NOOBJ as PG_UNMANAGED. (2) Defer the lock
assertion in pmap_page_is_mapped() until after PG_UNMANAGED is tested.
This is safe because both PG_UNMANAGED and PG_FICTITIOUS are immutable
flags, i.e., they do not change state between the time that a page is
allocated and freed.
Approved by: re (kensmith)
PR: 116794
TCP: [X.X.X.X]:X to [X.X.X.X]:X tcpflags 0x18<PUSH,ACK>; tcp_do_segment: FIN_WAIT_2: Received data after socket was closed, sending RST and removing tcpcb
So that it also includes how many bytes of data were received. It now looks
like this:
TCP: [X.X.X.X]:X to [X.X.X.X]:X tcpflags 0x18<PUSH,ACK>; tcp_do_segment: FIN_WAIT_2: Received X bytes of data after socket was closed, sending RST and removing tcpcb
Approved by: re (gnn)
not being independently freeable. This allows one to embed an mbuf in
the cluster itself. This confers the benefits of the packet zone on
all cluster sizes. Embedded mbufs currently suffer from the same
limitation that packet zone mbufs do in that one cannot disconnect
them and pass them around independently of the cluster. It would
likely be possible to eliminate this limitation in the future by
adding a second reference for the mbuf itself.
Approved by: re(gnn)
problems with the syncache, it produces a lot of console noise and has led
to quite a few false positive bug reports. It can be selectively
re-enabled when debugging specific problems by frobbing the same sysctl.
Discussed with: silby
Approved by: re (gnn)
directory itself (rather than any of its contents) is visible to the
current thread.
MFC after: 1 week
PR: kern/90063
Submitted by: john of 8192.net
Approved by: re (kensmith)
I also took the chance to make the list of supported devices a
bit more compact, as it was really long to read.
Even though re@ and Warner only saw the diffs for the code, i expect
their approval also covered the manpage update.
Approved by: re, imp (implicitly i hope)
MFC after: 3 days
with all functions supported. This is done adding usb device IDs
to the table of recognised devices (because there is no standard
'scanner' class, so no other way to recognise them), and with
a small change to the uscanner attach routine that prevents
reconfiguring the whole USB device while we are dealing only with
one of its USB interfaces.
The latter part has been suggested by Steinar Hamre in
http://www.freebsd.org/cgi/query-pr.cgi?pr=107665 , i have
only added a bit of explaination to the code.
I have personally tried this on the Epson DX-5050 and DX-6000
devices (on the US market they have different names, CX-something).
I have good reasons to think that, possibly with the mere addition
of more USB ids to the table in uscanner.c, this should work with
all Epson multifunction devices in that family (from DX-3800 to
DX-7000 - these units are in the 50-120$ price range).
More details on related topics (SANE configuration, OCR, etc.)
at http://info.iet.unipi.it/~luigi/FreeBSD/dx5050.html
Manpage updates coming soon.
Approved by: re, imp
MFC after: 3 days
with identical meaning as the colon ":". This is to support a syntax
that is more similar to a PCI device specification in the device hints
file. The selector is not fully compatible with the specification in
the hints file, since entries in that file use a different prefix,
which needs to be added to the getsel() routine, if full support of
that syntax is found to be desirable.
Approved by: re (Ken Smith)
PCI selectors with 2 or 3 elements behave exactly as before (i.e. the
domain is 0 and in the 2 element case, the function is also 0).
The form with 4 selector elements works as in the previous revision
and provides the PCI domain number as the left-most selector element.
This change allows old scripts (which used the 2 or 3 selector element
formats) to be kept. Without this patch, the 3 element form was parsed
as starting with a domain number (and the function was assumed to be 0),
with this patch, the domain is assumed to be 0 (and the last value is
used as the function number).
The man page is updated to describe the new selector semantics.
Approved by: re (Ken Smith)
