failing to load on a kernel that has "nodevice mem" in the config. It will
now properly bring in the mem(4) module.
Submitted by: antoine
Reviewed by: imp
MFC after: 1 week
ABI and the direction flag, that is it now assumes that the direction
flag is cleared at the entry of a function and it doesn't clear once
more if needed. This new behaviour conforms to the i386/amd64 ABI.
Modify the signal handler frame setup code to clear the DF {e,r}flags
bit on the amd64/i386 for the signal handlers.
jhb@ noted that it might break old apps if they assumed DF == 1 would be
preserved in the signal handlers, but that such apps should be rare and
that older versions of gcc would not generate such apps.
Submitted by: Aurelien Jarno <aurelien aurel32 net>
PR: 121422
Reviewed by: jhb
MFC after: 2 weeks
- Close a sleepqueue signal race by interlocking with the per-process
spinlock. This was mistakenly omitted from the thread_lock patch and
has been a race since.
MFC After: 1 week
PR: bin/117603
Reported by: Danny Braniss <danny@cs.huji.ac.il>
by default rather than the setmask. This is consistent with the linux
tool and more consistent with the notion that the default level is
the process level. The cpuset mask can still be modified by specifying
the -c option. You can not set the per-thread and cpuset mask in
a single command.
- Update the man page to reflect this change.
Contributed by: gallatin
PhysMask fields based on the number of physical address bits supported
by the current CPU. The old code assumed 36 bits on i386 and 40 bits on
amd64. In truth, all Intel CPUs up until recently used 36 bits (a newer
Intel CPU uses 38 bits) and all the Opteron CPUs used 40 bits.
In at least one case (the new Intel CPU) having the size of the mask field
wrong resulted in writing questionable values into the MTRR registers on
the application processors (BSP as well if you modify the MTRRs via
memcontrol or running X, etc.). The result of the questionable physmask
was that all of memory was apparently treated as uncached rather than
write-back resulting in a very significant performance hit.
Fix this by constructing a run-time mask for the PhysBase and PhysMask
fields based on the number of physical address bits supported by the CPU.
All 64-bit capable CPUs provide a count of PA bits supported via the
0x80000008 extended CPUID feature, so use that if it is available. If that
feature is not available, then assume 36 PA bits.
While I'm here, expand the (now-unused) macros for the PhysBase and
PhysMask fields to the current largest possible value (52 PA bits).
MFC after: 1 week
PR: i386/120516
Reported by: Nokia
filename table whose size is less than 65536 bytes.
The original intention was to not consume the filename table, so the
client will have a chance to look at it. To achieve that, the library
call decompressor->read_ahead to read(look ahead) but do not call
decompressor->consume to consume the data, thus a limit was raised
since read_ahead call can only look ahead at most BUFFER_SIZE(65536)
bytes at the moment, and you can not "look any further" before you
consume what you already "saw".
This commit will turn GNU/SVR4 filename table into "archive format
data", i.e., filename table will be consumed by libarchive, so the
65536-bytes limit will be gone, but client can no longer have access
to the content of filename table.
'ar' support test suite is changed accordingly. BSD ar(1) is not
affected by this change since it doesn't look at the filename table.
Reported by: erwin
Discussed with: jkoshy, kientzle
Reviewed by: jkoshy, kientzle
Approved by: jkoshy(mentor), kientzle
hangs (one at boot, one at shutdown) in recent machines. First, only try
to take ownership of the EHCI controller if the BIOS currently owns the
controller. On a HP DL160 G5, the machine hangs when we try to take
ownership. Second, don't bother trying to give up ownership of the
controller during shutdown. It's not strictly required and a Dell DCS S29
hangs on shutdown after the config write.
Both of these changes match the behavior of the Linux EHCI driver. I also
think both of these hangs are caused by bugs in the BIOS' SMM handler
causing it to get stuck in an infinite loop in SMM.
MFC after: 1 week
accept a mouse using the boot subclass. Instead, restore the original
hid_is_collection() test and fallback to testing the interface class,
subclass, and protocol if that fails.
MFC after: 1 week
PR: usb/118670
might be currently programmed into the registers.
Underlying firmware (U-Boot) would typically program MAC address into the
first unit only, and others are left uninitialized. It is now possible to
retrieve and program MAC address for all units properly, provided they were
passed on in the bootinfo metadata.
Reviewed by: imp, marcel
Approved by: cognet (mentor)
We're now more robust against cases of non-sorted and/or non-continuous
numbering of those entries.
Reviewed by: imp, marcel
Approved by: cognet (mentor)
This was introduced as a workaround long time ago for some Alpha firmware
(which is now gone), and actually prevented net_close() to ever be
called.
Certain firmwares (U-Boot) need local shutdown operations to be performed on a
network controller upon transaction end: such platform-specific hooks are
supposed to be called via netif_close() (from within net_close()).
This change effectively reverts the following CVS commit:
sys/boot/common/dev_net.c
revision 1.7
date: 2000/05/13 15:40:46; author: dfr; state: Exp; lines: +2 -1
Only probe network settings on the first open of the network device.
The alpha firmware takes a seriously long time to open the network device
the first time.
Also suppress excessive output while netbooting via loader, unless debugging.
While there, make sys/boot/uboot more style(9) compliant.
Reviewed by: imp
Approved by: cognet (mentor)
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
sched_sleep(). This removes extra thread_lock() acquisition and
allows the scheduler to decide what to do with the static boost.
- Change the priority arguments to cv_* to match sleepq/msleep/etc.
where 0 means no priority change. Catch -1 in cv_broadcastpri() and
convert it to 0 for now.
- Set a flag when sleeping in a way that is compatible with swapping
since direct priority comparisons are meaningless now.
- Add a sysctl to ule, kern.sched.static_boost, that defaults to on which
controls the boost behavior. Turning it off gives better performance
in some workloads but needs more investigation.
- While we're modifying sleepq, change signal and broadcast to both
return with the lock held as the lock was held on enter.
Reviewed by: jhb, peter
