on 900B and 635(A).
Re-add the enhanced PHY access register method again for older chipsets,
they do not seem to work with all old chips.
Reviewed by: phk
MFC after: 7 days
Allow to read EEPROM from LAN. It is shared
between a 1394 controller and the NIC and each
time we access it, we need to set SIS_EECMD_REQ.
Idea from: linux driver source
Reviewed by: luoqi
Obtained from: linux driver source (idea)
register, and phy has to be directly accessed via mdio.
Patch converted to CURRENT from STABLE.
Submitted by: luoqi
Reviewed by: luoqi (again)
MFC after: 2 weeks
the PCI bus. When this bit is set, the Max DMA Burst Size
for TX/RX DMA should be no larger than 64 bytes.
Reviewed by: luoqi
Obtained from: (idea from linux driver source)
MFC after: 2 weeks
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
Remove some unnecessary assignments to mbuf fields in sis_newbuf(),
the "length" fields are of no use while the mbuf is in the receive ring.
MFC after: 3 days
still queued for transmission. This should solve the problem of
the device stalling on transmissions if some link event prevents
transmission.
There are other drivers which have the same problem and need to be
fixed in the same way.
MFC after: 3 days
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
motherboard chipsets. We need to force the chip to reload its MAC address
into the receive filter, and enable software access mode for the PHY.
PR: kern/33294
Non-SMP, i386-only, no polling in the idle loop at the moment.
To use this code you must compile a kernel with
options DEVICE_POLLING
and at runtime enable polling with
sysctl kern.polling.enable=1
The percentage of CPU reserved to userland can be set with
sysctl kern.polling.user_frac=NN (default is 50)
while the remainder is used by polling device drivers and netisr's.
These are the only two variables that you should need to touch. There
are a few more parameters in kern.polling but the default values
are adequate for all purposes. See the code in kern_poll.c for
more details on them.
Polling in the idle loop will be implemented shortly by introducing
a kernel thread which does the job. Until then, the amount of CPU
dedicated to polling will never exceed (100-user_frac).
The equivalent (actually, better) code for -stable is at
http://info.iet.unipi.it/~luigi/polling/
and also supports polling in the idle loop.
NOTE to Alpha developers:
There is really nothing in this code that is i386-specific.
If you move the 2 lines supporting the new option from
sys/conf/{files,options}.i386 to sys/conf/{files,options} I am
pretty sure that this should work on the Alpha as well, just that
I do not have a suitable test box to try it. If someone feels like
trying it, I would appreciate it.
NOTE to other developers:
sure some things could be done better, and as always I am open to
constructive criticism, which a few of you have already given and
I greatly appreciated.
However, before proposing radical architectural changes, please
take some time to possibly try out this code, or at the very least
read the comments in kern_poll.c, especially re. the reason why I
am using a soft netisr and cannot (I believe) replace it with a
simple timeout.
Quick description of files touched by this commit:
sys/conf/files.i386
new file kern/kern_poll.c
sys/conf/options.i386
new option
sys/i386/i386/trap.c
poll in trap (disabled by default)
sys/kern/kern_clock.c
initialization and hardclock hooks.
sys/kern/kern_intr.c
minor swi_net changes
sys/kern/kern_poll.c
the bulk of the code.
sys/net/if.h
new flag
sys/net/if_var.h
declaration for functions used in device drivers.
sys/net/netisr.h
NETISR_POLL
sys/dev/fxp/if_fxp.c
sys/dev/fxp/if_fxpvar.h
sys/pci/if_dc.c
sys/pci/if_dcreg.h
sys/pci/if_sis.c
sys/pci/if_sisreg.h
device driver modifications
The reason we are required to commit to -current first is so that later
MFC's do not risk the loss of existing bug fixes. Even if this was not
strictly required in -current, it should still be fixed there too.
mbuf allocation fails, and fix (i hope) a couple of style bugs.
I believe these printf() are extremely dangerous because now they can
occur on every incoming packet and are not rate limited. They were
meant to warn the sysadmin about lack of resources, but now they
can become a nice way to panic your system under load.
Other drivers (e.g. the fxp driver) have nothing like this.
There is a pending discussion on putting this kind of warnings
elsewhere, and I hope we can fix this soon.
have alignment problems.
On small boxes (e.g. the net4501 from Soekris, featuring a 486/133)
this provides huge performance benefits: the peak forwarding rate
with avg.sized packets goes up by 50-70% because of this change
alone. Faster CPUs might benefit less from this change, but in any
case the CPU has better things to do than waste time on useless
memory-to-memory copies.
Several drivers (for Tulip-like cards) might benefit from a similar
change.
Right now the new behaviour is controlled by a sysctl variable,
hw.sis_quick which defaults to 1 (on), you can set it to 0 to
reintroduce the old behaviour (and compare the results). The
variable is only there to show how much you can gain with this
change, it will go away soon.
Also, slightly simplify the code to initialize the ring buffers,
and remove a couple of dangerous printf's which could trigger on
any packet in case of mbuf shortage.
MFC-after: 3 days
idle and the driver would not detect the event, requiring userland
to cycle the interface to bring it up again.
The fix consists in adding SIS_IMR_RX_IDLE to the interrupt mask and
add a command in sis_intr() to restart the receiver when this happens.
While at it, make the test of status bits more efficient.
calling vtophys() and contigmalloc()/contigfree() directly. Hopefully,
I have shaken out all of the problems with busdma on the alpha now.
(Everything seems to work as expected.)
Also, change the max RX DMA limit to 1024 bytes instead of "unlimited,"
as the latter seems not to work correctly on the alpha that I tested.
(At 100Mbps, all attempts to receive frames yield RX errors.)
something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
chipset. The MAC address is stored in the APC CMOS RAM and we have to
commit trememdous evil in order to read it. The code to do this is only
activated on the i386 platform. Thanks to Cameron Grant for providing
access to a test box for me to tinker with.
This will fix the problem where the sis driver ends up with a station
address of 00:00:00:00:00:00 on boards that use the 630E chipset.
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
- Modify the driver to poll the link state and positively set the
MAC to full or half duplex as needed. Previously, it was possible
for the MAC to remain in half duplex even though the PHY had negotiated
full duplex with its link partner, which would result in bursty
performance.
- Program some of the NatSemi's registers as specified by the datasheet.
The manual says these are necessary for "optimum perofrmance," though
a couple of them are marked as reserved in the register map. *shrug*
- Select the TX DMA burst size correctly for 10 and 100mbps modes.
Previously I was using 64 bytes in both modes, which worked in
100mbps mode, but resulting in spotty performance in 10mbps.
32 bytes works much better; without this change, the natsemi
chip yields piss poor performance at 10mbps.
With these fixes, the NatSemi chip finally performs to my satisfaction.
I should be merging the support for this controller into -stable shortly.
Phew.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
controller chip. This chip is currently being used on the NetGear
FA312-TX adapter, which I guess is a replacement for the FA310-TX
(PNIC-based).
I added support for this chip by modifying the sis driver since
the SiS 900 and the NS DP83815 have almost the same programming
interface (the RX filter programming and PHY access methods are
different, but the general configuration, DMA scheme and register
layout are identical).
I would have had this done a lot sooner, but getting the damn MAC
address out of the EEPROM proved to be more complicated than expected.
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
