supported architectures such as the alpha. This allows us to save
on kernel virtual address space, TLB entries, and (on the ia64) VHPT
entries. pmap_map() now modifies the passed in virtual address on
architectures that do not support direct-mapped segments to point to
the next available virtual address. It also returns the actual
address that the request was mapped to.
- On the IA64 don't use a special zone of PV entries needed for early
calls to pmap_kenter() during pmap_init(). This gets us in trouble
because we end up trying to use the zone allocator before it is
initialized. Instead, with the pmap_map() change, the number of needed
PV entries is small enough that we can get by with a static pool that is
used until pmap_init() is complete.
Submitted by: dfr
Debugging help: peter
Tested by: me
of memory, rather than from the start.
This fixes problems allocating bouncebuffers on alphas where there is only
1 chunk of memory (unlike PCs where there is generally at least one small
chunk and a large chunk). Having 1 chunk had been fatal, because these
structures take over 13MB on a machine with 1GB of ram. This doesn't leave
much room for other structures and bounce buffers if they're at the front.
Reviewed by: dfr, anderson@cs.duke.edu, silence on -arch
Tested by: Yoriaki FUJIMORI <fujimori@grafin.fujimori.cache.waseda.ac.jp>
in 4.2-REL which I ripped out in -stable and -current when implementing the
low-memory handling solution. However, maxlaunder turns out to be the saving
grace in certain very heavily loaded systems (e.g. newsreader box). The new
algorithm limits the number of pages laundered in the first pageout daemon
pass. If that is not sufficient then suceessive will be run without any
limit.
Write I/O is now pipelined using two sysctls, vfs.lorunningspace and
vfs.hirunningspace. This prevents excessive buffered writes in the
disk queues which cause long (multi-second) delays for reads. It leads
to more stable (less jerky) and generally faster I/O streaming to disk
by allowing required read ops (e.g. for indirect blocks and such) to occur
without interrupting the write stream, amoung other things.
NOTE: eventually, filesystem write I/O pipelining needs to be done on a
per-device basis. At the moment it is globalized.
The fix works by reverting the ordering of free memory so that the
chances of contig_malloc() succeeding increases.
PR: 23291
Submitted by: Andrew Atrens <atrens@nortel.ca>
Removed most of the hacks that were trying to deal with low-memory
situations prior to now.
The new code is based on the concept that I/O must be able to function in
a low memory situation. All major modules related to I/O (except
networking) have been adjusted to allow allocation out of the system
reserve memory pool. These modules now detect a low memory situation but
rather then block they instead continue to operate, then return resources
to the memory pool instead of cache them or leave them wired.
Code has been added to stall in a low-memory situation prior to a vnode
being locked.
Thus situations where a process blocks in a low-memory condition while
holding a locked vnode have been reduced to near nothing. Not only will
I/O continue to operate, but many prior deadlock conditions simply no
longer exist.
Implement a number of VFS/BIO fixes
(found by Ian): in biodone(), bogus-page replacement code, the loop
was not properly incrementing loop variables prior to a continue
statement. We do not believe this code can be hit anyway but we
aren't taking any chances. We'll turn the whole section into a
panic (as it already is in brelse()) after the release is rolled.
In biodone(), the foff calculation was incorrectly
clamped to the iosize, causing the wrong foff to be calculated
for pages in the case of an I/O error or biodone() called without
initiating I/O. The problem always caused a panic before. Now it
doesn't. The problem is mainly an issue with NFS.
Fixed casts for ~PAGE_MASK. This code worked properly before only
because the calculations use signed arithmatic. Better to properly
extend PAGE_MASK first before inverting it for the 64 bit masking
op.
In brelse(), the bogus_page fixup code was improperly throwing
away the original contents of 'm' when it did the j-loop to
fix the bogus pages. The result was that it would potentially
invalidate parts of the *WRONG* page(!), leading to corruption.
There may still be cases where a background bitmap write is
being duplicated, causing potential corruption. We have identified
a potentially serious bug related to this but the fix is still TBD.
So instead this patch contains a KASSERT to detect the problem
and panic the machine rather then continue to corrupt the filesystem.
The problem does not occur very often.. it is very hard to
reproduce, and it may or may not be the cause of the corruption
people have reported.
Review by: (VFS/BIO: mckusick, Ian Dowse <iedowse@maths.tcd.ie>)
Testing by: (VM/Deadlock) Paul Saab <ps@yahoo-inc.com>
and sysv shared memory support for it. It implements a new
PG_UNMANAGED flag that has slightly different characteristics
from PG_FICTICIOUS.
A new sysctl, kern.ipc.shm_use_phys has been added to enable the
use of physically-backed sysv shared memory rather then swap-backed.
Physically backed shm segments are not tracked with PV entries,
allowing programs which use a large shm segment as a rendezvous
point to operate without eating an insane amount of KVM in the
PV entry management. Read: Oracle.
Peter's OBJT_PHYS object will also allow us to eventually implement
page-table sharing and/or 4MB physical page support for such segments.
We're half way there.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
madvise().
This feature prevents the update daemon from gratuitously flushing
dirty pages associated with a mapped file-backed region of memory. The
system pager will still page the memory as necessary and the VM system
will still be fully coherent with the filesystem. Modifications made
by other means to the same area of memory, for example by write(), are
unaffected. The feature works on a page-granularity basis.
MAP_NOSYNC allows one to use mmap() to share memory between processes
without incuring any significant filesystem overhead, putting it in
the same performance category as SysV Shared memory and anonymous memory.
Reviewed by: julian, alc, dg
instead of duplicating the code. (2) If a wired page is passed
to vm_page_free_toq, panic instead of printing a friendly warning.
(If we don't panic here, we'll just panic later in vm_page_unwire
obscuring the problem.)
eliminate an extra (useless) level of indirection in half of the page
queue accesses and (2) to use a single name for each queue throughout,
instead of, e.g., "vm_page_queue_active" in some places and
"vm_page_queues[PQ_ACTIVE]" in others.
Reviewed by: dillon
Merge the contents (less some trivial bordering the silly comments)
of <vm/vm_prot.h> and <vm/vm_inherit.h> into <vm/vm.h>. This puts
the #defines for the vm_inherit_t and vm_prot_t types next to their
typedefs.
This paves the road for the commit to follow shortly: change
useracc() to use VM_PROT_{READ|WRITE} rather than B_{READ|WRITE}
as argument.
Replace various VM related page count calculations strewn over the
VM code with inlines to aid in readability and to reduce fragility
in the code where modules depend on the same test being performed
to properly sleep and wakeup.
Split out a portion of the page deactivation code into an inline
in vm_page.c to support vm_page_dontneed().
add vm_page_dontneed(), which handles the madvise MADV_DONTNEED
feature in a related commit coming up for vm_map.c/vm_object.c. This
code prevents degenerate cases where an essentially active page may
be rotated through a subset of the paging lists, resulting in premature
disposal.
Remove the initialization of PQ_NONE's cnt and lcnt. They aren't
used.
vm_page_insert:
Remove an unnecessary dereference.
vm_page_wire:
Remove the one and only (and thus pointless) reference
to PQ_NONE's lcnt.
piecemeal, middle-of-file writes for NFS. These hacks have caused no
end of trouble, especially when combined with mmap(). I've removed
them. Instead, NFS will issue a read-before-write to fully
instantiate the struct buf containing the write. NFS does, however,
optimize piecemeal appends to files. For most common file operations,
you will not notice the difference. The sole remaining fragment in
the VFS/BIO system is b_dirtyoff/end, which NFS uses to avoid cache
coherency issues with read-merge-write style operations. NFS also
optimizes the write-covers-entire-buffer case by avoiding the
read-before-write. There is quite a bit of room for further
optimization in these areas.
The VM system marks pages fully-valid (AKA vm_page_t->valid =
VM_PAGE_BITS_ALL) in several places, most noteably in vm_fault. This
is not correct operation. The vm_pager_get_pages() code is now
responsible for marking VM pages all-valid. A number of VM helper
routines have been added to aid in zeroing-out the invalid portions of
a VM page prior to the page being marked all-valid. This operation is
necessary to properly support mmap(). The zeroing occurs most often
when dealing with file-EOF situations. Several bugs have been fixed
in the NFS subsystem, including bits handling file and directory EOF
situations and buf->b_flags consistancy issues relating to clearing
B_ERROR & B_INVAL, and handling B_DONE.
getblk() and allocbuf() have been rewritten. B_CACHE operation is now
formally defined in comments and more straightforward in
implementation. B_CACHE for VMIO buffers is based on the validity of
the backing store. B_CACHE for non-VMIO buffers is based simply on
whether the buffer is B_INVAL or not (B_CACHE set if B_INVAL clear,
and vise-versa). biodone() is now responsible for setting B_CACHE
when a successful read completes. B_CACHE is also set when a bdwrite()
is initiated and when a bwrite() is initiated. VFS VOP_BWRITE
routines (there are only two - nfs_bwrite() and bwrite()) are now
expected to set B_CACHE. This means that bowrite() and bawrite() also
set B_CACHE indirectly.
There are a number of places in the code which were previously using
buf->b_bufsize (which is DEV_BSIZE aligned) when they should have
been using buf->b_bcount. These have been fixed. getblk() now clears
B_DONE on return because the rest of the system is so bad about
dealing with B_DONE.
Major fixes to NFS/TCP have been made. A server-side bug could cause
requests to be lost by the server due to nfs_realign() overwriting
other rpc's in the same TCP mbuf chain. The server's kernel must be
recompiled to get the benefit of the fixes.
Submitted by: Matthew Dillon <dillon@apollo.backplane.com>
unallocated parts of the last page when the file ended on a frag
but not a page boundary.
Delimitted by tags PRE_MATT_MMAP_EOF and POST_MATT_MMAP_EOF,
in files alpha/alpha/pmap.c i386/i386/pmap.c nfs/nfs_bio.c vm/pmap.h
vm/vm_page.c vm/vm_page.h vm/vnode_pager.c miscfs/specfs/spec_vnops.c
ufs/ufs/ufs_readwrite.c kern/vfs_bio.c
Submitted by: Matt Dillon <dillon@freebsd.org>
Reviewed by: Alan Cox <alc@freebsd.org>
address) so that the first 16MB of physical memory is allocated
last rather than first. On large-memory machines, this avoids
the exhaustion of low physical memory before isa_dmainit has run.
Fix bug where an object's OBJ_WRITEABLE/OBJ_MIGHTBEDIRTY flags do
not get set under certain circumstances ( page rename case ).
Reviewed by: Alan Cox <alc@cs.rice.edu>, John Dyson
been made but the code has been reorganized and documented to make
it more readable, reduce the size of the code, and optimize the branch
path caching capabilities that most modern processors have.
PQ_FREE. There is little operational difference other then the kernel
being a few kilobytes smaller and the code being more readable.
* vm_page_select_free() has been *greatly* simplified.
* The PQ_ZERO page queue and supporting structures have been removed
* vm_page_zero_idle() revamped (see below)
PG_ZERO setting and clearing has been migrated from vm_page_alloc()
to vm_page_free[_zero]() and will eventually be guarenteed to remain
tracked throughout a page's life ( if it isn't already ).
When a page is freed, PG_ZERO pages are appended to the appropriate
tailq in the PQ_FREE queue while non-PG_ZERO pages are prepended.
When locating a new free page, PG_ZERO selection operates from within
vm_page_list_find() ( get page from end of queue instead of beginning
of queue ) and then only occurs in the nominal critical path case. If
the nominal case misses, both normal and zero-page allocation devolves
into the same _vm_page_list_find() select code without any specific
zero-page optimizations.
Additionally, vm_page_zero_idle() has been revamped. Hysteresis has been
added and zero-page tracking adjusted to conform with the other changes.
Currently hysteresis is set at 1/3 (lo) and 1/2 (hi) the number of free
pages. We may wish to increase both parameters as time permits. The
hysteresis is designed to avoid silly zeroing in borderline allocation/free
situations.
vm_page_rename(), but never pulled the page off PQ_CACHE if it was on
PQ_CACHE. Dirty pages in PQ_CACHE are not allowed and a KASSERT was
added in -4.x to test for this... and got hit.
In -4.x, vm_page_rename() automatically dirties the page. This commit
also has it deal with the PQ_CACHE case, deactivating the page in that
case.
pointers per entry ). The table has been changed to a singly linked
list of vm_page_t pointers. The table has been doubled in size, but
the entries only take half the space so a net-zero change in memory use.
The hash function has been changed, hopefully for the better. The
combination of the larger hash table size of changed function should
keep the chain length down to a reasonable number (0-3, average 1).
vm_object->page_hint has been removed. This 'optimization' was not
only never needed, but costs as much as a hash chain link to implement.
While having page_hint in vm_object might result in better locality
of reference, the cost is not worth the space in vm_object or the
extra instructions in my view.
vm_page_alloc*() functions have been inlined and call a generalized
non-inlined vm_page_alloc_toq() which combines the standard alloc
and zero-page alloc functions together, reducing code size and the L1
cache footprint. Some reordering has been done... not much. The
delinking code should be faster ( because unlinking a doubly-linked list
requires four memory ops and unlinking a singly linked list only requires
two ), and we get a hash consistancy check for free.
vm_page_rename() now automatically sets the page's dirty bits.
vm_page_alloc() does not try to manually inline freeing a cache page.
Instead, it now properly calls vm_page_free(m) ... vm_page_free() is
really too complex to manually inline.
vm_await(), supporting asleep(), has been added.
changes to the VM system to support the new swapper, VM bug
fixes, several VM optimizations, and some additional revamping of the
VM code. The specific bug fixes will be documented with additional
forced commits. This commit is somewhat rough in regards to code
cleanup issues.
Reviewed by: "John S. Dyson" <root@dyson.iquest.net>, "David Greenman" <dg@root.com>
Add some overflow checks to read/write (from bde).
Change all modifications to vm_page::flags, vm_page::busy, vm_object::flags
and vm_object::paging_in_progress to use operations which are not
interruptable.
Reviewed by: Bruce Evans <bde@zeta.org.au>
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
the page offset. If a large file offset was passed in, a large negative
array index could be generated which could cause page faults etc at worst
and file corruption at the least. (Pages are allocated within file
space on page alignment boundaries, so a file offset being passed in here
is harmless to DTRT. The case where this was happening has already been
fixed though, this is in case it happens again).
Reviewed by: dyson
problems. Tor Egge and others have helped with various VM bugs
lately, but don't blame him -- blame me!!!
pmap.c:
1) Create an object for kernel page table allocations. This
fixes a bogus allocation method previously used for such, by
grabbing pages from the kernel object, using bogus pindexes.
(This was a code cleanup, and perhaps a minor system stability
issue.)
pmap.c:
2) Pre-set the modify and accessed bits when prudent. This will
decrease bus traffic under certain circumstances.
vfs_bio.c, vfs_cluster.c:
3) Rather than calculating the beginning virtual byte offset
multiple times, stick the offset into the buffer header, so
that the calculated offset can be reused. (Long long multiplies
are often expensive, and this is a probably unmeasurable performance
improvement, and code cleanup.)
vfs_bio.c:
4) Handle write recursion more intelligently (but not perfectly) so
that it is less likely to cause a system panic, and is also
much more robust.
vfs_bio.c:
5) getblk incorrectly wrote out blocks that are incorrectly sized.
The problem is fixed, and writes blocks out ONLY when B_DELWRI
is true.
vfs_bio.c:
6) Check that already constituted buffers have fully valid pages. If
not, then make sure that the B_CACHE bit is not set. (This was
a major source of Sig-11 type problems.)
vfs_bio.c:
7) Fix a potential system deadlock due to an incorrectly specified
sleep priority while waiting for a buffer write operation. The
change that I made opens the system up to serious problems, and
we need to examine the issue of process sleep priorities.
vfs_cluster.c, vfs_bio.c:
8) Make clustered reads work more correctly (and more completely)
when buffers are already constituted, but not fully valid.
(This was another system reliability issue.)
vfs_subr.c, ffs_inode.c:
9) Create a vtruncbuf function, which is used by filesystems that
can truncate files. The vinvalbuf forced a file sync type operation,
while vtruncbuf only invalidates the buffers past the new end of file,
and also invalidates the appropriate pages. (This was a system reliabiliy
and performance issue.)
10) Modify FFS to use vtruncbuf.
vm_object.c:
11) Make the object rundown mechanism for OBJT_VNODE type objects work
more correctly. Included in that fix, create pager entries for
the OBJT_DEAD pager type, so that paging requests that might slip
in during race conditions are properly handled. (This was a system
reliability issue.)
vm_page.c:
12) Make some of the page validation routines be a little less picky
about arguments passed to them. Also, support page invalidation
change the object generation count so that we handle generation
counts a little more robustly.
vm_pageout.c:
13) Further reduce pageout daemon activity when the system doesn't
need help from it. There should be no additional performance
decrease even when the pageout daemon is running. (This was
a significant performance issue.)
vnode_pager.c:
14) Teach the vnode pager to handle race conditions during vnode
deallocations.
has been some bitrot and incorrect assumptions in the vfs_bio code. These
problems have manifest themselves worse on NFS type filesystems, but can
still affect local filesystems under certain circumstances. Most of
the problems have involved mmap consistancy, and as a side-effect broke
the vfs.ioopt code. This code might have been committed seperately, but
almost everything is interrelated.
1) Allow (pmap_object_init_pt) prefaulting of buffer-busy pages that
are fully valid.
2) Rather than deactivating erroneously read initial (header) pages in
kern_exec, we now free them.
3) Fix the rundown of non-VMIO buffers that are in an inconsistent
(missing vp) state.
4) Fix the disassociation of pages from buffers in brelse. The previous
code had rotted and was faulty in a couple of important circumstances.
5) Remove a gratuitious buffer wakeup in vfs_vmio_release.
6) Remove a crufty and currently unused cluster mechanism for VBLK
files in vfs_bio_awrite. When the code is functional, I'll add back
a cleaner version.
7) The page busy count wakeups assocated with the buffer cache usage were
incorrectly cleaned up in a previous commit by me. Revert to the
original, correct version, but with a cleaner implementation.
8) The cluster read code now tries to keep data associated with buffers
more aggressively (without breaking the heuristics) when it is presumed
that the read data (buffers) will be soon needed.
9) Change to filesystem lockmgr locks so that they use LK_NOPAUSE. The
delay loop waiting is not useful for filesystem locks, due to the
length of the time intervals.
10) Correct and clean-up spec_getpages.
11) Implement a fully functional nfs_getpages, nfs_putpages.
12) Fix nfs_write so that modifications are coherent with the NFS data on
the server disk (at least as well as NFS seems to allow.)
13) Properly support MS_INVALIDATE on NFS.
14) Properly pass down MS_INVALIDATE to lower levels of the VM code from
vm_map_clean.
15) Better support the notion of pages being busy but valid, so that
fewer in-transit waits occur. (use p->busy more for pageouts instead
of PG_BUSY.) Since the page is fully valid, it is still usable for
reads.
16) It is possible (in error) for cached pages to be busy. Make the
page allocation code handle that case correctly. (It should probably
be a printf or panic, but I want the system to handle coding errors
robustly. I'll probably add a printf.)
17) Correct the design and usage of vm_page_sleep. It didn't handle
consistancy problems very well, so make the design a little less
lofty. After vm_page_sleep, if it ever blocked, it is still important
to relookup the page (if the object generation count changed), and
verify it's status (always.)
18) In vm_pageout.c, vm_pageout_clean had rotted, so clean that up.
19) Push the page busy for writes and VM_PROT_READ into vm_pageout_flush.
20) Fix vm_pager_put_pages and it's descendents to support an int flag
instead of a boolean, so that we can pass down the invalidate bit.
2) Do not unnecessarily force page blocking when paging
pages out.
3) Further improve swap pager performance and correctness,
including fixing the paging in progress deadlock (except
in severe I/O error conditions.)
4) Enable vfs_ioopt=1 as a default.
5) Fix and enable the page prezeroing in SMP mode.
All in all, SMP systems especially should show a significant
improvement in "snappyness."
of the various ad-hoc schemes.
2) When bringing in UPAGES, the pmap code needs to do another vm_page_lookup.
3) When appropriate, set the PG_A or PG_M bits a-priori to both avoid some
processor errata, and to minimize redundant processor updating of page
tables.
4) Modify pmap_protect so that it can only remove permissions (as it
originally supported.) The additional capability is not needed.
5) Streamline read-only to read-write page mappings.
6) For pmap_copy_page, don't enable write mapping for source page.
7) Correct and clean-up pmap_incore.
8) Cluster initial kern_exec pagin.
9) Removal of some minor lint from kern_malloc.
10) Correct some ioopt code.
11) Remove some dead code from the MI swapout routine.
12) Correct vm_object_deallocate (to remove backing_object ref.)
13) Fix dead object handling, that had problems under heavy memory load.
14) Add minor vm_page_lookup improvements.
15) Some pages are not in objects, and make sure that the vm_page.c can
properly support such pages.
16) Add some more page deficit handling.
17) Some minor code readability improvements.
MUST be PG_BUSY. It is bogus to free a page that isn't busy,
because it is in a state of being "unavailable" when being
freed. The additional advantage is that the page_remove code
has a better cross-check that the page should be busy and
unavailable for other use. There were some minor problems
with the collapse code, and this plugs those subtile "holes."
Also, the vfs_bio code wasn't checking correctly for PG_BUSY
pages. I am going to develop a more consistant scheme for
grabbing pages, busy or otherwise. For now, we are stuck
with the current morass.
1) Start using TSM.
Struct procs continue to point to upages structure, after being freed.
Struct vmspace continues to point to pte object and kva space for kstack.
u_map is now superfluous.
2) vm_map's don't need to be reference counted. They always exist either
in the kernel or in a vmspace. The vmspaces are managed by reference
counts.
3) Remove the "wired" vm_map nonsense.
4) No need to keep a cache of kernel stack kva's.
5) Get rid of strange looking ++var, and change to var++.
6) Change more data structures to use our "zone" allocator. Added
struct proc, struct vmspace and struct vnode. This saves a significant
amount of kva space and physical memory. Additionally, this enables
TSM for the zone managed memory.
7) Keep ioopt disabled for now.
8) Remove the now bogus "single use" map concept.
9) Use generation counts or id's for data structures residing in TSM, where
it allows us to avoid unneeded restart overhead during traversals, where
blocking might occur.
10) Account better for memory deficits, so the pageout daemon will be able
to make enough memory available (experimental.)
11) Fix some vnode locking problems. (From Tor, I think.)
12) Add a check in ufs_lookup, to avoid lots of unneeded calls to bcmp.
(experimental.)
13) Significantly shrink, cleanup, and make slightly faster the vm_fault.c
code. Use generation counts, get rid of unneded collpase operations,
and clean up the cluster code.
14) Make vm_zone more suitable for TSM.
This commit is partially as a result of discussions and contributions from
other people, including DG, Tor Egge, PHK, and probably others that I
have forgotten to attribute (so let me know, if I forgot.)
This is not the infamous, final cleanup of the vnode stuff, but a necessary
step. Vnode mgmt should be correct, but things might still change, and
there is still some missing stuff (like ioopt, and physical backing of
non-merged cache files, debugging of layering concepts.)
config option in pmap. Fix a problem with faulting in pages. Clean-up
some loose ends in swap pager memory management.
The system should be much more stable, but all subtile bugs aren't fixed yet.
Fix the UIO optimization code.
Fix an assumption in vm_map_insert regarding allocation of swap pagers.
Fix an spl problem in the collapse handling in vm_object_deallocate.
When pages are freed from vnode objects, and the criteria for putting
the associated vnode onto the free list is reached, either put the
vnode onto the list, or put it onto an interrupt safe version of the
list, for further transfer onto the actual free list.
Some minor syntax changes changing pre-decs, pre-incs to post versions.
Remove a bogus timeout (that I added for debugging) from vn_lock.
PHK will likely still have problems with the vnode list management, and
so do I, but it is better than it was.
of vnodes and objects. There are some metadata performance improvements
that come along with this. There are also a few prototypes added when
the need is noticed. Changes include:
1) Cleaning up vref, vget.
2) Removal of the object cache.
3) Nuke vnode_pager_uncache and friends, because they aren't needed anymore.
4) Correct some missing LK_RETRY's in vn_lock.
5) Correct the page range in the code for msync.
Be gentle, and please give me feedback asap.
the pageout daemon wasn't always being waken up appropriately when the
(cache + free) queues were depleted.
Submitted by: David S. Miller <davem@jenolan.rutgers.edu>
changes, so don't expect to be able to run the kernel as-is (very well)
without the appropriate Lite/2 userland changes.
The system boots and can mount UFS filesystems.
Untested: ext2fs, msdosfs, NFS
Known problems: Incorrect Berkeley ID strings in some files.
Mount_std mounts will not work until the getfsent
library routine is changed.
Reviewed by: various people
Submitted by: Jeffery Hsu <hsu@freebsd.org>
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
problem of allocating contiguous buffer memory in general, but
make it much more likely to work at boot-up time. The best
chance for an LKM-type load of a sound driver is immediately
after the mount of the root filesystem.
This appears to work for a 64K allocation on an 8MB system.
`show vmopag', `show page' and `show pageq'. Moved all vm ddb stuff
to the ends of the vm source files.
Changed printf() to db_printf(), `indent' to db_indent, and iprintf()
to db_iprintf() in ddb commands. Moved db_indent and db_iprintf()
from vm to ddb.
vm_page.c:
Don't use __pure. Staticized.
db_output.c:
Reduced page width from 80 to 79 to inhibit double spacing for long
lines (there are still some problems if words are printed across
column 79).
The default level works with minimal overhead, but one can also enable
full, efficient use of a 512K cache. (Parameters can be generated
to support arbitrary cache sizes also.)
problem with the 'shell scripts' was found, but there was a 'strange'
problem found with a 486 laptop that we could not find. This commit
backs the code back to 25-jul, and will be re-entered after the snapshot
in smaller (more easily tested) chunks.
performance issues.
1) The pmap module has had too many inlines, and so the
object file is simply bigger than it needs to be.
Some common code is also merged into subroutines.
2) Removal of some *evil* PHYS_TO_VM_PAGE macro calls.
Unfortunately, a few have needed to be added also.
The removal caused the need for more vm_page_lookups.
I added lookup hints to minimize the need for the
page table lookup operations.
3) Removal of some bogus performance improvements, that
mostly made the code more complex (tracking individual
page table page updates unnecessarily). Those improvements
actually hurt 386 processors perf (not that people who
worry about perf use 386 processors anymore :-)).
4) Changed pv queue manipulations/structures to be TAILQ's.
5) The pv queue code has had some performance problems since
day one. Some significant scalability issues are resolved
by threading the pv entries from the pmap AND the physical
address instead of just the physical address. This makes
certain pmap operations run much faster. This does
not affect most micro-benchmarks, but should help loaded system
performance *significantly*. DG helped and came up with most
of the solution for this one.
6) Most if not all pmap bit operations follow the pattern:
pmap_test_bit();
pmap_clear_bit();
That made for twice the necessary pv list traversal. The
pmap interface now supports only pmap_tc_bit type operations:
pmap_[test/clear]_modified, pmap_[test/clear]_referenced.
Additionally, the modified routine now takes a vm_page_t arg
instead of a phys address. This eliminates a PHYS_TO_VM_PAGE
operation.
7) Several rewrites of routines that contain redundant code to
use common routines, so that there is a greater likelihood of
keeping the cache footprint smaller.
Re-enables the RSS limiting, and the routine is now tail-recursive,
making it much more safe (eliminates the possiblity of kernel stack
overflow.) Also, the RSS limiting is a little more intelligent about
finding the likely objects that are pushing the process over the limit.
Added some sysctls that help with VM system tuning.
New sysctl features:
1) Enable/disable lru pageout algorithm.
vm.pageout_algorithm = 0, default algorithm that works
well, especially using X windows and heavy
memory loading. Can have adverse effects,
sometimes slowing down program loading.
vm.pageout_algorithm = 1, close to true LRU. Works much
better than clock, etc. Does not work as well as
the default algorithm in general. Certain memory
"malloc" type benchmarks work a little better with
this setting.
Please give me feedback on the performance results
associated with these.
2) Enable/disable swapping.
vm.swapping_enabled = 1, default.
vm.swapping_enabled = 0, useful for cases where swapping
degrades performance.
The config option "NO_SWAPPING" is still operative, and
takes precedence over the sysctl. If "NO_SWAPPING" is
specified, the sysctl still exists, but "vm.swapping_enabled"
is hard-wired to "0".
Each of these can be changed "on the fly."
