rather than a fixed 512... This fixes the mount root problem on at91.
Prior to the SD card reorg, all data transfers were 512 bytes, so we
didn't notice.
the serial port class when we set the devclass since it is now
no-longer a compile time constant. Eliminate the pci include, as it
isn't relevant or necessary.
time constant. This allows us to potentially change it at runtime or
autodetect it early in the boot (the latter being much more likely to
have a good outcome).
- To avoid having a bunch of locks that end up always getting acquired as
a group, give each ppc(4) device a mutex which it shares with all the
child devices including ppbus(4), lpt(4), plip(4), etc. This mutex
is then used for all the locking.
- Rework the interrupt handling stuff yet again. Now ppbus drivers setup
their interrupt handler during attach and tear it down during detach
like most other drivers. ppbus(4) only invokes the interrupt handler
of the device that currently owns the bus (if any) when an interrupt
occurs, however. Also, interrupt handlers in general now accept their
softc pointers as their argument rather than the device_t. Another
feature of the ppbus interrupt handlers is that they are called with
the parent ppc device's lock already held. This minimizes the number
of lock operations during an interrupt.
- Mark plip(4), lpt(4), pcfclock(4), ppi(4), vpo(4) MPSAFE.
- lpbb(4) uses the ppc lock instead of Giant.
- Other plip(4) changes:
- Add a mutex to protect the global tables in plip(4) and free them on
module unload.
- Add a detach routine.
- Split out the init/stop code from the ioctl routine into separate
functions.
- Other lpt(4) changes:
- Use device_printf().
- Use a dedicated callout for the lptout timer.
- Allocate the I/O buffers at attach and detach rather than during
open and close as this simplifies the locking at the cost of
1024+32 bytes when the driver is attached.
- Other ppi(4) changes:
- Use an sx lock to serialize open and close.
- Remove unused HADBUS flag.
- Add a detach routine.
- Use a malloc'd buffer for each read and write to avoid races with
concurrent read/write.
- Other pps(4) changes:
- Use a callout rather than a callout handle with timeout().
- Conform to the new ppbus requirements (regular mutex, non-filter
interrupt handler). pps(4) is probably going to have to become a
standalone driver that doesn't use ppbus(4) to satisfy it's
requirements for low latency as a result.
- Use an sx lock to serialize open and close.
- Other vpo(4) changes:
- Use the parent ppc device's lock to create the CAM sim instead of
Giant.
- Other ppc(4) changes:
- Fix ppc_isa's detach method to detach instead of calling attach.
Tested by: no one :-(
Some time ago I tried adding Unicode rendering to the teken demo
application, but I didn't get it working. It seems I forgot to call
setlocale(). Polish this code and make sure it doesn't get lost.
Also a small fix for my previous commit: all Unicode characters in
teken_boxdrawing are below 0x10000, so store them as 16-bit values.
o Only set 4-bit caps on those boards that have 4-bit caps (this means that
because we don't set wire4 yet, this forces us to always use 1-bit bus).
o Don't test wire4 when setting up the bus width, since bad things will
happen if we do.
# This likely won't fix the busted at91 sd card support, but these are
# needful changes for correctness.
the helper function. It is supposed to be useful for any filesystem
that has to unlock dvp to walk to the ".." entry in lookup routine.
Requested by: jhb
Tested by: pho
MFC after: 1 month
VOP_MARKATIME() since unlike the rest of VOP_SETATTR(), VA_MARKATIME
can be performed while holding a shared vnode lock (the same functionality
is done internally by VOP_READ which can run with a shared vnode lock).
Add missing locking of the vnode interlock to the ufs implementation and
remove a special note and test from the NFS client about not supporting the
feature.
Inspired by: ups
Tested by: pho
section of code, this uses WITNESS_NORELEASE() and WITNESS_RELEASEOK() to mark
the boundaries. Both functions require the lock to be held when calling.
This is intended for scenarios like a bus asserting that the bus lock is not
dropped during a driver call. There doesn't appear to be a man page to
document this in.
Reviewed by: jhb
indirect block pages are not removed by the mentioned invocation of
the vnode_pager_setsize().
Put a common code into the helper function ffs_pages_remove().
Reported and tested by: dchagin
Reviewed by: ups
MFC after: 3 weeks
- Always program RX configuration register from scratch instead of
doing read/modify/write.
- Rename re_setmulti() to re_set_rxmode() to be reflect reality.
- Simplify hash filter logic a little while I am here.
Reviewed by: yongari (early version)
the fsbase value. The switch loads the fs segment register, that
invalidates the value in fsbase msr, thus value in %r9 can not be
considered the current value for fsbase anymore.
Unconditionally reload fsbase when switching to 32bit binary.
PR: 130526
MFC after: 3 weeks
Even though VT100-like devices can display non-ASCII characters, they do
not use an 8-bit character set. Special escape sequences allow the VT100
to switch character maps. The special graphics character set stores the
box drawing characters, starting at 0x60, ending at 0x7e. This means
we now pass the character map tests in vttest, even the save/restore
cursor test, combined with character maps. dialog(1) also works a lot
better now.
This commit also includes some other minor fixes:
- Default to 24 lines in teken_demo when using xterm emulation.
- Make white foreground and background work in teken_demo.
address space where to put vnode pages, and then call UFS_BALLOC(),
to actually allocate new block and map it. When UFS_BALLOC() returns
error, sometimes we forget to revert the vm object size increase,
allowing for the pages that are not backed by the logical disk blocks.
Revert vnode_pager_setsize() back when UFS_BALLOC() failed, for
ffs_truncate() and ffs_write().
PR: 129956
Reviewed by: ups
MFC after: 3 weeks
vnode, from -1 down. When vinvalbuf(vp, V_ALT) is done for the vnode, it
incorrectly does vm_object_page_remove(0, 0), removing all pages from
the underlying vm object, not only the pages that back the extended
attributes data.
Change vinvalbuf() to not remove any pages from the object when
V_NORMAL or V_ALT are specified. Instead, the only in-tree caller
in ffs_inode.c:ffs_truncate() that specifies V_ALT explicitely
removes the corresponding page range. The V_NORMAL caller
does vnode_pager_setsize(vp, 0) immediately after the call to
vinvalbuf(V_NORMAL) already.
Reported by: csjp
Reviewed by: ups
MFC after: 3 weeks
In normal operation, the number of cache entries is roughly equal to the
number of active vnodes. However, when most of the recently accessed
vnodes have many hard links, the number of cache entries can be 32000
times as large, exhausting kernel memory and provoking a panic in
kmem_malloc().
MFC after: 2 weeks
