Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
has a PS/2 port, this is a good thing. Note, older 386/486 boxes may
lockup the keyboard controller with this enabled, but most of these kinds
of machines don't run -current, so the benefits outweigh the downsides.
Discussed with: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
This driver includes the following patches submitted by:
1.0 Hideyuki Suzuki <hideyuki@sat.t.u-tokyo.ac.jp>
Japanese Cable support
2.0 Keith Sklower <sklower@CS.Berkeley.EDU>
Minor update to the BSDI section so it compiles cleanly on BSDI
3.0 Joao Carlos Mendes Luis <jonny@coppe.ufrj.br>
ioctl interface to select video format , NTSC, PAL, etc...
- CPU_CYRIX_NO_LOCK enables weak locking. If this option is not set and
FAILESAFE is defined, NO_LOCK bit of CCR1 is cleared.
- CPU_WT_ALLOC enables write-through allocation.
in a P6 SMP system. Some MB bios'es don't set the registers up correctly
for the AP's. Additionally, set the memory between 0xa0000 and 0xbffff
as write combining.
shown to be harmful in that it results in the card not being detected
properly on warmboot due to the station address failing to be read
correctly from the NVRAM.
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
It seems I didn't count my 0's properly when adding the new masks into
icu_vector.s pushing SWI_AST_MASK off the end of the array and screwing
up the indexing for SWI_CLOCK_MASK.
Fix the bug icu_vector.s and also reformat the code in both icu_vector.s and
apic_vector.s so that it will be much harder to make the same mistake in
the future.
Submitted by: Bruce Evans <bde@zeta.org.au>
machine generates an NMI for each floating point error, just like an old XT.
Since it is ISA only, reading the EISA status port yields 0xff, which would
give a spurious EISA panic. The simplest thing to do is to ignore the 0xff.
operands that are set during seqeuncer program download instead of at
assembly time.
Remove the REJBYTE sram variable. The host driver can just as easly
read the accumulator to get this value.
This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.
Doug Ledford determined the cause of the problem, fixes by me.
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
report slightly more than 64MB of total memory. This can happen due to the
total being the sum of both base and extended memory.
Submitted by: Alan Cox <alc@cs.rice.edu>
buffer queue so I missed this when I changed buf_queue_head.
This probably fixes Soren's problem too, but he never mentioned
which CD driver he was using. 8-)
Submitted by: dave adkins <adkin003@tc.umn.edu>
Add cpu_rootconf and cpu_dumpconf so that configuring these
two devices can be better controlled by the MI configuration
code.
machdep.c:
MD initialization code for the new callout interface.
trap.c:
Add support for printing out whether cam interrupts are masked
during a panic.
plus the previous changes to use the zone allocator decrease the useage
of malloc by half. The Zone allocator will be upgradeable to be able
to use per CPU-pools, and has more intelligent usage of SPLs. Additionally,
it has reasonable stats gathering capabilities, while making most calls
inline.
the normal CS4326 except that it's had it's ID's tweaked for some reason)
Also mark the device as alive in the attach routine so that the pnp system
doesn't think the attach failed.
possible. (This is not really a typographical improvement in the
case of the K6 it seems, but AMD appearantly want it too look
that way). Also if bootverbose, dump some more info about the
chip.
of multiple PCI IDE controllers(Dyson), and some updates and cleanups from
John Hood, who originally made our IDE DMA stuff work :-).
I have run tests with 7 IDE drives connected to my system, all in DMA
mode, with no errors. Modulo any bugs, this stuff makes IDE look
really good (within it's limitations.)
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
internal modems. Currently detects a USR modem, and a couple Supra
modems... vendor id's for sio capabile cards welcomed...
document new option EXTRA_SIO that will increase sio's internal data
structures to support X more serial ports... these are used by the
PnP part of sio for attaching... If you don't have it specified, it
will default to 2... This is defaulted to 0 if you don't have PnP
compiled into your kernel...
also document that if you set the PnP flags (pnp x flags y) to 0x1 that
the modem will be refused to be recognized by the sio driver... this
is for people that want the traditional isa driver to probe and attach
the modem... (for keeping legacy sio numbering)
these structs for conflics...
it still exist that two PnP cards can colide, but this is up to the user
to make sure it doesn't happen...
other modifications to pnp.c to format output properly, and hide more
output behind bootverbose flag...
fix some bugons in pnp.h that would of made it difficult for inclusion
in external programs (for import of pnpinfo)
number of dma overruns/underruns for systems under heavy dma load.
As a side effect, broken enhanced floppy controllers that sometimes
don't detect dma overruns/underruns will give less errors.
Reviewed by: j@uriah.heep.sax.de (J Wunsch)
Hide the bogus FDC ``chip type'' display behind a (mostly) undocumented
option, since people started to trust the bogus claim. Once we're going
to handle 2.88 MB controllers, we have to redo the chip detection, by
now just leave it hidden.
files.i386.
We aren't sure if this new code and the old sound code will co-exist in a
kernel, so the device pcm0 line is left commented out in LINT.
Submitted-by: Luigi Rizzo
was 0.
PR: 4164
Submitted by: Joe Traister <traister@mojozone.org>
While i was at it, also fixed a broken return value for the VT_RELDISP
ioctl, iff the third arg was legally VT_TRUE, but the destination
screen was in process mode so the actual switch had to be deferred.
This was breaking the ability to directly toggle between two X servers
running on two VTs, since the server getting the bogus error return
was running wild, and competing with the other one for the hardware.
(Sigh, this was a very long-standing bug.)
PR: 4486
Submitted by: tegge@idi.ntnu.no (Tor Egge)
Implement a function is_adapter_memory() in order to determine what
should nto be dumped at all. Currently, only populated with the ``ISA
memory hole''. Adapter regions of other busses should be added.
you don't want this (and the documentation explains why), but if you
use ipfw as an as-needed casual filter as needed which normally runs as
'allow all' then having the kernel and /sbin/ipfw get out of sync is a
*MAJOR* pain in the behind.
PR: 4141
Submitted by: Heikki Suonsivu <hsu@mail.clinet.fi>
This code has been submitted by Luigi Rizzo <luigi@labinfo.iet.unipi.it>,
based on work done by Sujal Patel.
This currnetly doesn't provide the ability to register the port address
of PnP cards assigned a PnP driver. As there aren't any PnP capible
drivers yet, this isn't much of a problem.
The code allows you, through USERCONFIG, configure what the cards port
bases, irqs, and dma's are like. Currently there isn't support to view
what cards are in the sytem.
It successfully configures my PnP Internal Modem and sio then sees the
card as a normal isa device.
man page will be committed shortly.
Approved-by: jkh
Submitted-by: Luigi Rizzo
delay that without this the performance is unacceptable. The 83C690,
83C790, and 83C795 chips which this affects are all designed to work
with 0 waitstates in 16bit mode.
Also cleaned up the toggling of 16bit access mode that occurs during
normal operation; the previous code may not have done the right thing
in all cases.
mode, the slash is a comment leader, while under non-elf it is a divide
symbol (what a concept! :-). Theoretically, #APP/#NO_APP can change this
but that doesn't seem to mesh too well with macros and line continuation.
while waiting for an interrupt (rather than spinning on the runqueue status
bits), since the other cpu can put stuff in there and the sleeping cpu may
not get an interrupt for a while. When we have a reschedule IPI, this can
come back.
Pointed out by: fsmp
size in terms of lines (instead of bytes). When changing video mode
in ioctl SW_XXX commands, syscons checks scp->history_size and
allocate a history buffer at least as large as the new screen size.
(This was unnecessary before, because HISTORY_SIZE was as large as 100
lines and this is bigger than the maximum screen size: 60 lines).
Similar adjustment is done in ioctl CONS_HISTORY command too.
PR: kern/4169
Reviewed by: sos
* lots of fixes to error handling-- mostly works now
* improve DMA timing config for Triton chipsets-- PIIX4 and UDMA drive
still untested
* generally improve DMA config in many ways-- mostly cleanup
* clean up boot-time messages
* rewrite PRD generation algorithm
* first wd timeout is now longer, to handle drive spinup
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
are met:
1) The BIOS indicates that there is exactly 64MB of RAM, and
2) The memory size isn't specified with the MAXMEM option or
the npx0 msize hack,
...then do a speculative memory probe beyond the 64MB's until the
first bad page is encountered. This is an admitted hack, but should
nonetheless deal with detecting the correct amount of memory in nearly
all of the modern systems with >64MB of RAM.
Also made a change that will cause the list of detected memory chunks
to be printed if bootverbose is set.
2) Added a non_blocking flag to the write routine.
3) Added a 3rd buffer (actually a ring buffer would be better)
Submitted by: Jim Lowe <james@miller.cs.uwm.edu>
holding CPU along with the lock. When a CPU fails to get the lock
it compares its own id to the holder id. If they are the same it
panic()s, as simple locks are binary, and this would cause a deadlock.
Controlled by smptests.h: SL_DEBUG, ON by default.
Some minor cleanup.
and hardware.
There is now another simple_lock around clock data/hardware accesses in
clock.c and microtime.s. It is my belief that this is the only area
sio/cy might stumble into during an unblocked INTerrupt. Thus I separated
the sio/cy code from the generic disable_intr()/enable_intr() routines.
Controlled by smptests.h: USE_COMLOCK, ON by default.
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
and the sound driver which uses auto dma.
The dma interface functionality remains however it now checks
to see if a dma is operating in auto dma mode and if so it bypasses
the busy flag check . I have modified the sound driver 3.5 to
adjust for this new behavior and tested it under FreeBSD 3.0 -current
This patch also includes the new function isa_dmastop.
Submitted by: Amancio Hasty <hasty@rah.star-gate.com>
smp_active = 1 used to indicate that the system had frozen previously
started AP's, while smp_active = 0 was "AP's not yet started". I have split
this into smp_started (which is set when the AP's come online), and
smp_active is left for turning on/off AP scheduling.
- We now have enough per-cpu idle context, the real idle loop has been
revived (cpu's halt now with nothing to do).
- Some preliminary support for running some operations outside the
global lock (eg: zeroing "free but not yet zeroed pages") is present
but appears to cause problems. Off by default.
- the smp_active sysctl now behaves differently. It's merely a 'true/false'
option. Setting smp_active to zero causes the AP's to halt in the idle
loop and stop scheduling processes.
- bootstrap is a lot safer. Instead of sharing a statically compiled in
stack a number of times (which has caused lots of problems) and then
abandoning it, we use the idle context to boot the AP's directly. This
should help >2 cpu support since the bootlock stuff was in doubt.
- print physical apic id in traps.. helps identify private pages getting
out of sync. (You don't want to know how much hair I tore out with this!)
More cleanup to follow, this is more of a checkpoint than a
'finished' thing.
irqs can't work (at best, the first one attached wins). It used to
be necessary to skip this check because of bogus irqs in the sound
drivers, but the sound drivers have been fixed, except possibly the
OSS ones.
arg of type u_short (just write the function in ANSI C like most
other functions in this file instead of fixing the interface or
depending on a gcc feature).
vm_inherit_t. These types are smaller than ints, so the prototypes
should have used the promoted type (int) to match the old-style function
definitions. They use just vm_prot_t and/or vm_inherit_t. This depends
on gcc features to work. I fixed the definitions since this is easiest.
The correct fix may be to change the small types to u_int, to optimize
for time instead of space.
wasted.
Fixed type mismatches for functions with vm_prot_t's as args. vm_prot_t
is u_char, so the prototypes should have used promoteof(u_char) to match
the old-style function definitions. They use just vm_prot_t. This depends
on gcc features to work. I fixed the definitions since this is easiest.
The correct fix may be to change vm_prot_t to u_int, to optimize for time
instead of space.
Removed a stale comment.
Added a new variable, 'bsp_apic_ready', which is set as soon as the bootstrap
CPU has initialized its local APIC. Conditionalize the GENSPLR functions
to call ss_lock ONLY after bsp_apic_ready is TRUE; This should prevent
any problems with races between the time the 1st AP becomes ready and the
time smp_active is set.
region protected by the simplelock 'cpl_lock'.
Notes:
- this code is currently controlled on a section by section basis with
defines in machine/param.h. All sections are currently enabled.
- this code is not as clean as I would like, but that can wait till later.
- the "giant lock" still surrounds most instances of this "cpl region".
I still have to do the code that arbitrates setting cpl between the
top and bottom halves of the kernel.
- the possibility of deadlock exists, I am committing the code at this
point so as to exercise it and detect any such cases B4 the "giant lock"
is removed.
pause before attempting to reset the sequencer address. Remove the
loop checking to see if the address has gone to zero since it is
unnecessary
Adjust the abort SCB timeouts back up to 2 seconds where they should
be.
Fix an oversight in the removal of the bus reset settle code where
we might not run the queue of completed commands.
Remove an unecessary call to ahc_run_done_queue in ahc_reset_current_bus.
Submitted by: Tor Egge <Tor.Egge@idi.ntnu.no>
Made NEW_STRATEGY default.
Removed misc. old cruft.
Centralized simple locks into mp_machdep.c
Centralized simple lock macros into param.h
More cleanup in the direction of making splxx()/cpl MP-safe.
I have no way of testing this one, first SMP/cy user please let me know...
It is my belief that sio and cy are the only FAST_INTR() ISRs. If this
is a bad assumption please educate me.
Several new fine-grained locks.
New FAST_INTR() methods:
- separate simplelock for FAST_INTR, no more giant lock.
- FAST_INTR()s no longer checks ipending on way out of ISR.
sio made MP-safe (I hope).
