include the ithread scheduling step. Without this, a preemption might
occur in between the interrupt getting masked and the ithread getting
scheduled. Since the interrupt handler runs in the context of curthread,
the scheudler might see it as having a such a low priority on a busy system
that it doesn't get to run for a _long_ time, leaving the interrupt stranded
in a disabled state. The only way that the preemption can happen is by
a fast/filter handler triggering a schduling event earlier in the handler,
so this problem can only happen for cases where an interrupt is being
shared by both a fast/filter handler and an ithread handler. Unfortunately,
it seems to be common for this sharing to happen with network and USB
devices, for example. This fixes many of the mysterious TCP session
timeouts and NIC watchdogs that were being reported. Many thanks to Sam
Lefler for getting to the bottom of this problem.
Reviewed by: jhb, jeff, silby
Note that ULong in this code is actually defined as an unsigned integer across
all arches so that the gdtoa() function always processes 32 bit data
despite the unfortunate naming of "ULong".
- Bring HEAD up to the latest shared code
- Fix TSO problem using limited MSS and forwarding
- Dual lock implementation
- New device support
- For my ease, this code can compile in either 6.x or later
- brings this driver in sync with the 6.3
prepend a data mbuf in front of a header mbuf without moving the header
to the new mbuf, and (2) a possible alignment problem on architectures
with strict alignment as reported in kern/4184.
PR: kern/4184 (1)
addresses as the source of an AARP request. While this PR was submitted
in the context of work in OpenBSD to port netatalk (in 1997), I've
synchronized the code more to our ARP input routine, which had similar
requirements.
Submitted by: Denton Gentry
PR: kern/4184
MFC after: 1 week
only at address 0 which is supposed to be the only valid phy address
on Marvell PHY. The more correct solution would be masking PHY
address ranges allowable in PHY probe routine. Unfortunately,
FreeBSD has no way to retrict the PHY address ranges or to pass special
flags to PHY driver.
This change assumes that PHY hardwares attached to msk(4) would be
Marvell made 88E11xx PHY.
With this changes the phantom phys attached on 88E8036(Yukon FE)
should disappear.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
only 4KB SRAM.
o Rework setting Tx/Rx RAM buffer size. Give receiver 2/3 of memory
and round it down to the multiple of 1024. The RAM buffer size of
Yukon II should be multiple of 1024. This fixes bogus RAM buffer
configuration used in Yukon FE.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
timestamps in the initial SYN packet actually use them in the rest of the
connection. Unfortunately, during the 7.0 testing cycle users have already
found network devices that violate this constraint.
RFC 1323 states 'and may send a TSopt in other segments' rather than
'and MUST send', so we must allow it.
Discovered by: Rob Zietlow
Tracked down by: Kip Macy
PR: bin/118005
publicly available datasheet for Yukon II and don't know what
bug/workaround exist for the specific hardware revision. Also I don't
think the vendor will release hardware errata in near future.
The hardware feature lists were not used at all except setting water
mark registers. Since msk(4) should know exact chip model/revision
number to decide which hardware capability could be used the extra
feature lists were redundant.
o Enable jumbo frame support for EC Ultra and disable jumbo frame
for FE.
o Enable store and forward mode for standard MTU sized frame.
o Enable TSO for EC Ultra. However TSO/checksum offload is disabled
for jumbo frame case. Because EC Ultra can't use store and forward
mode for jumbo frame TSO/checksum offload is not available.
o Adjust Tx GMAC almost empty threshold value and add a jumbo frame
water mark. The maic value was obtained from Marvell's sk98lin
driver.
o Fix EC Ultra chip revision number.
libraries had not had their versions bumped relative to 6.3-REL but
had indeed been changed. We need to bump their version so they can be
properly added to the compat6x port:
libasn1.so.8 libgssapi.so.8 libhdb.so.8 libkadm5clnt.so.8
libkadm5srv.so.8 libkafs5.so.8 libkrb5.so.8 libobjc.so.2
MFC After: 1 day
doesn't use the default CFLAGS which contain -fno-strict-aliasing.
Until the code is cleaned up, just add -fno-strict-aliasing to the
CFLAGS of these for the tinderboxes' sake, allowing the rest of the
tree to have -Werror enabled again.
rwlocks in conjuction with callouts. The function does basically what
callout_init_mtx() alredy does with the difference of using a rwlock
as extra argument.
CALLOUT_SHAREDLOCK flag can be used, now, in order to acquire the lock only
in read mode when running the callout handler. It has no effects when used
in conjuction with mtx.
In order to implement this, underlying callout functions have been made
completely lock type-unaware, so accordingly with this, sysctl
debug.to_avg_mtxcalls is now changed in the generic
debug.to_avg_lockcalls.
Note: currently the allowed lock classes are mutexes and rwlocks because
callout handlers run in softclock swi, so they cannot sleep and they
cannot acquire sleepable locks like sx or lockmgr.
Requested by: kmacy, pjd, rwatson
Reviewed by: jhb
obstacle to enabling -Werror. I'll continue to work on cleaning up the
code so that we can keep this enabled.
If the tinderboxes would just use the default CFLAGS set in this file,
all would be fine and we'd be able to make use of -Werror.
Revert the probe in atapi-cd.c to the old usage now its fixed on AHCI.
THis change also fixes using virtual CD's om fx parallels.
Still leaves the GEOM problem of telling media vs device access apart in the access function.
server-side RPC retranmission cache for non-idempotent operations: these
hacks substituted 0 (success) for the expected EEXIST in the event that
a target name already existed for LINK, SYMLINK, and MKDIR operations,
under the assumption that EEXIST represented a second application of the
original RPC rather than a true failure.
Background: certain NFS operations (in this case, LINK, SYMLINK, and
MKDIR) are not idempotent, as they leave behind persisting state on the
server that prevents them from being replayed without an error;if an UDP
RPC reply is lost leading to a retransmission by theclient, the second
reply will return EEXIST rather than success, asthe new object has
already been created. The NFS client previouslysilently mapped the
EEXIST return into success to paper over thisproblem.
However, in all modern NFS server implementations, a reply cache is kept
in order to retransmit the original reply to a retransmitted request,
rather than performing the operation a second time, allowing this hack
to be avoided. This allows link()-based filelocking over NFS to operate
correctly, as an application requestingthe creation of a new link for a
file to tell if it succeededatomically or not.
Other NFS clients, including Solaris and Linux, generally follow this
behavior for the same reasons. Most clients also now default to TCP,
which also helps avoid the issue of retransmitted but non-idempotent
requests in most cases.
Reported by: Adam McDougall <mcdouga9 at egr dot msu dot edu>,
Timo Sirainen <tss at iki dot fi>
Reviewed by: mohans
MFC after: 1 week
o buffered write, for chunks smaller than PIPE_MINDIRECT bytes
o direct write, for everything else
A call to writev(2) may receive struct iov of various size and the
kernel may have to switch from one solution to the other. Before doing
this, it must wake reader processes and any select/poll/kqueue up.
This commit fixes a bug where select/poll/kqueue are not triggered
when switching from buffered write to direct write. It adds calls to
pipeselwakeup().
I give more details on freebsd-arch@:
http://lists.freebsd.org/pipermail/freebsd-arch/2007-September/006790.html
This should fix issues with Erlang (lang/erlang) and kqueue.
Reported by: Rickard Green (Erlang)
