we create the pty on the fly when it is first opened.
If you run out of ptys now, just MAKEDEV some more.
This also demonstrate the use of dev_t->si_tty_tty and dev_t->si_drv1
in a device driver.
- %q -> %ll.
Fixed nearby errors not reported by gcc -Wformat on i386's:
- don't assume that the promotion of [u_]int64_t is [u_]quad_t.
- don't use signed formats for unsigned args.
- %q -> %ll; don't assume that the promotion of off_t is quad_t; only
assume that off_t's are representable as long longs.
- printing of dev_t's was completely broken.
Fixed nearby printf format errors not reported by gcc -Wformat on i386's:
- printing of ino_t's and pointers was sloppy.
kernels again, now that we're using EGCS/GCC 2.9+. This "here"
file is compatible with the Bourne shell and the Korn shell (incl. pdksh
and KSH93 from AT&T, which I do have), so it doesn't make newvers.sh
unportable, but makes it easier to modify in the future/read now.
Submitted by: green
warnings of the following nature on reloading a kld:
WARNING: "vinum" is usurping "console"'s bmaj
This only applies to cases where "console" is mentioned.
Broken-by: grog
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
update_plex_state:
If any subdisk in the plex is initializing, set the plex to
initializing state. This gets rid of the ugly corrupt/degraded/up
transitions which previously occurred.
Desired-by: Steve Taylor <staylor@cybernet.com>
sddownstate:
Add new function, used by checksdstate.
checksdstate:
Let sddownstate decide what status to return.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
logrq: save device major and minor numbers to compensate for lost
dev_t.
launch_requests: Don't issue requests which are marked
XFR_BAD_SUBDISK. This may make things easier in bre().
bre:
Rearrange.
- Change some comments
- Recognize holes in plex structure. Formerly this could lead to
incorrect write to the plex. Return REQUEST_DEGRADED on a read
request, but carry on to the bitter end on a write request, and
mark the requests for the inaccessible subdisks with
XFR_BAD_SUBDISK.
- return REQUEST_EOF if the requested transfer goes beyond the end
of the plex. This is not an error, since other plexes may go
further into the volume address space.
build_read_request:
Handle REQUEST_DEGRADED returned from bre().
sdio:
Lock buffer before issuing the requests.
will only accept partitions of type 'vinum'.
format_config: Use the new %q format option in kvprintf, thus getting
rid of some of the filthiest code I've written in a long time. Also
remove the lltoa() function.
With-great-thanks-to: peter
format_config: Accept the fact that a subdisk might not be attached to
a plex, and save the config correctly.
vinum_scandisk: Scan all slices on a drive with a Microsoft partition
table. Only look at the compatibility slice if nothing was found in
the Microsoft slices.
This change removes a frequently employed method of shooting
yourself in the foot: people would decide that the Vinum drives
belonged on their own slice, and they wouldn't be able to start the
subsystem after a reboot. Documentation updates to follow.
initialize subdisks. Probably the plex-related subdisk type will die
a death.
vinumconfig.c:
Accept (and ignore) kernel state information in userland config
files. This saves a lot of error recovery and also makes it possible
to use the output of printconfig to create new configuration.
Remove checkdiskconfig(). It wasn't needed any more.
Start adding support for hot spare drives. You can't put anything on
them (yet).
Change message formats from %lld to %qd.
get_empty_sd: Initialize size to -1. Previously this was done in
config_subdisk, which is the wrong place.
start_config: set current drive, plex and volume to -1, thus stopping
update configurations from taking their defaults from old configs.
in the pathname translation procedure. This proves fatal, and can be
easily fixed. This or a similar change needs to be committed to svr4_util.h
and ibcs2_util.h. I will update ibcs2_util.h, if noone else thinks of a
better way to do this, in the same manner. I will leave svr4 to the
respective maintainer.
This closes the problem of the only crash I've been able to produce as
a user recently, except for (currently not-in-the-source tree) fd
table sharing fixes. Thanks goes to pho for his stress-testers.
of 2 weeks ago that this be done, and anyone who wishes to make bpf more
selective according to securelevel or compile-time options is more
than free to do so.
is, don't assume that SCSI ID corresponds to a unit number of da
device. Unit number of da device is provided by 2nd stage loader
and 3rd stage loader now use it.
- Fix drive letter to display.
Submitted by: IMAI Takeshi <take-i@ceres.dti.ne.jp>
bootable on 1 FDD PC98 machines. (When an external FDD unit is
installed, unit numbers become discontinuous.)
Submitted by: IMAI Takeshi <take-i@ceres.dti.ne.jp>
now used in f_ops in place of NULL, and modifications to the files
are more carefully ordered. f_ops should also be set to &badfileops
upon "close" of a file.
This does not fix other problems mentioned in this PR than the first
one.
PR: 11629
Reviewed by: peter
correct the pointers afterwards.
It's kinda bogus that we generate a 24 (?) byte filehandle (2 x int32
fsid and 16 byte VFS fhandle) and pad it out to 64 bytes for NFSv3 with
garbage. The whole point of NFSv3's variable filehandle length was
to allow for shorter handles, both in memory and over the wire. I plan
on taking a shot at fixing this shortly.
o use suser_xxx rather than suser to support JAIL code.
o KNF comment convention
o use vp->type rather than vaddr.type and eliminate call to
VOP_GETATTR. Bruce says that vp->type is valid at this
point.
Submitted by: bde.
Not fixed:
o return (value)
o Comment needs to be longer and more explicit. It will be after
the advisory.
reset command.
I observed some anomalous behavior while testing a 3c905C with a
Dell PowerEdge 4300/500 dual PIII 500Mhz system. The NIC would seem
to work correctly most of the time but would sometimes fail to receive
certain packets, in particular NFS create requests. I could mount
an NFS filesystem from the PowerEdge and do an ls on it, but trying
to do a "touch foo" would hang. Monitoring traffic from another host
revealed that the client was properly sending an NFS create request
but the server was not receiving it. It *did* receive it when I
ran the same test with an Intel fxp card.
I don't understand the exact mechanics of this strange behavior, but
resetting the receiver and transmitter seems to get rid of it. I used
to perform an RX and TX reset in xl_init(), but stopped doing it there
because on 3c905B and later cards this causes the autoneg session to
restart, which would lead to the NIC waiting a long time before exchanging
traffic after being brought up the first time. Apparently the receiver
and transmitter resets should be performed at least once when initializing
the card.
Hopefully this will cure problems that people have been having with the
3c905C -- this was the only strange behavior that I have observed with
the 3c905C so far which does not appear with the 3c905B or 3c905.
eisa_add_intr() which now takes an additional arguement (one of
EISA_TRIGGER_LEVEL or EISA_TRIGGER_EDGE).
The flag RR_SHAREABLE has no effect when passed to
bus_alloc_resource(dev, SYS_RES_IRQ, ...) in an EISA device context as
the eisa_alloc_resource() call (bus_alloc_resource method) now deals
with this flag directly, depending on the device ivars.
This change does nothing more than move all the 'shared = inb(foo + iobsse)'
nonesense to the device probe methods rather than the device attach.
Also, print out 'edge' or 'level' in the IRQ announcement message.
Reviewed by: dfr
o Add field to dev_desc for the size of the io port range. This isn't
used yet in the committed sources, but will make the transition easier
in the future.
If you build this into your kernel, you will need to rebuild pccardd.
_or_ you may specify "log logamount number" to set logging specifically
the rule.
In addition, "ipfw resetlog" has been added, which will reset the
logging counters on any/all rule(s). ipfw resetlog does not affect
the packet/byte counters (as ipfw reset does), and is the only "set"
command that can be run at securelevel >= 3.
This should address complaints about not being able to set logging
amounts, not being able to restart logging at a high securelevel,
and not being able to just reset logging without resetting all of the
counters in a rule.
Specifically intended for removing -fschg ("INSTALLFLAGS_EDIT=:S/schg/uchg/")
this makes the NOFSCHG flag redundant. NOFSCHG will still be honoured by
bsd.lib.mk but is valid for buildworld only. NOFSCHG is still implemented in
the old way (ie. _not_ ".if NOFSCHG then { INSTALLFLAGS_EDIT+=:S/schg/,/ }"
to emphasize the fact that NOFSCHG is only supported in a limited
fashion and for buildworld.
The interface and implementation are such that future use of flags such
as sappnd can also be easily removed or altered (perhaps to uappnd).
This commit brought to you by the letters B, D, and E, and the numbers six,
one, thirteen, and three.
Remove the initialization of PQ_NONE's cnt and lcnt. They aren't
used.
vm_page_insert:
Remove an unnecessary dereference.
vm_page_wire:
Remove the one and only (and thus pointless) reference
to PQ_NONE's lcnt.
I did some tcpdumping the other day and noticed that GETATTR calls
were frequently followed by an ACCESS call to the same file. The
attached patch changes nfs_getattr to fill the access cache as a side
effect. This is accomplished by calling ACCESS rather than
GETATTR. This implies a modest overhead of 4 bytes in the request and
8 bytes in the response compared to doing a vanilla GETATTR.
...
[The patch comprises two parts] The first
is the "real" patch, the second counts misses and hits rather than
fills and hits. The difference is subtle but important because both
nfs_getattr and nfs_access now fill the cache. It also changes the
default value of nfsaccess_cache_timeout to better match the attribute
cache. IMHO, file timestamps change much more frequently than
protection bits.
Submitted by: Bjoern Groenvall <bg@sics.se>
Reviewed by: dillon (partially)
their svr4_stat64 structures with old dev_t values instead of udev_t's.
Panic was caused when major() and minor() were called with args which
weren't pointers. The panic was probably introduced in rev 1.51 of
kern_conf.c
vnodes are locked and never unlocked, which leads to processes starting
to wedge up after doing a mount -o nfsv3,tcp,rdirplus foo:/fs /fs; ls /fs.
The second is that sometimes cnp is accessed without having been
properly initialized: cnp->cn_nameptr points to an earlier name while
"len" contains the length of a current name of different size. This
leads to an attempt to dereference *(cn->cn_nameptr + len) which will
sometimes cause a page fault and a panic.
With these two fixes, client side readdirplus works correctly with
FreeBSD, IRIX 6.5.4 and Solaris 2.5.1 and 2.6 servers.
Submitted by: Matthew Dillon <dillon@backplane.com>
being incremented by 4 bytes too few each time through the loop, which
allows more data into the mbuf chain that we really want. In the worst
case, when we're using 32K read/write sizes with a TCP client, this causes
readdirplus replies to sometimes exceed NFS_MAXPACKET which leads to a
panic. This problem cropped up for me using an IRIX 6.5.4 NFSv3 TCP client
with 32K read/write sizes, however supposedly it can be triggered by
WinNT NFS servers too. In theory, it can probably be triggered by any
NFS v3 implementation using TCP as long as it's using the maxiumum block
size.
Reviewed by: Matthew Dillon <dillon@backplane.com>
space of PCI devices that don't exist cause PCI master & target aborts
rather than returning ~0 or giving a machine check. Bring in some code
from NetBSD to handle this properly.
obtained from: NetBSD
reviewed by: dfr
- Add support for calling 32-bit code in other segments
- Add support for calling 16-bit protected mode code
Update APM to use this facility.
Submitted by: jlemon
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
result of a joined effort with parts contributed by Doug Rabson, Warner
Losh and Stefan Esser (hope I did not forget anybody). Part of the sources
is obtained from NetBSD with modifications.
This code is work in progress:
As of the time of the initial import, a loader.exe executable is built,
which can be loaded on an Alpha with NT only firmware, but no attempt is
made to switch to OSF PAL code as required to start an actual kernel.
active or not. The only sane thing we can do here is assume that if
APM is supported it might be active at some point, and bail.
In reality, even this isn't good enough; regardless of whether we support
APM or not, the system may well futz with the CPU's clock speed and throw
the TSC off. We need to stop using it for timekeeping except under
controlled circumstances. Curse the lack of a dependable high-resolution
timer.
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
macros) to the signal handler, for old-style BSD signal handlers as
the second (int) argument, for SA_SIGINFO signal handlers as
siginfo_t->si_code. This is source-compatible with Solaris, except
that we have no <siginfo.h> (which isn't even mentioned in POSIX
1003.1b).
An rather complete example program is at
http://www3.cons.org/cracauer/freebsd-signal.c
This will be added to the regression tests in src/.
This commit also adds code to disable the (hardware) FPU from
userconfig, so that you can use a software FP emulator on a machine
that has hardware floating point. See LINT.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
Translated from: a similar fix in ufs_readwrite.c rev.1.61.
Don't forget to set DE_ACCESS for short reads.
Check for invalid (negative) offsets before checking for reads of
0 bytes, as in ufs, although checking for invalid offsets at all
is probably a bug.
Set IN_ACCESS for successful reads of 0 bytes (except for requests to
read 0 bytes). This was broken in rev.1.42.
PR: misc/10148
Don't set IN_ACCESS for requests to read 0 bytes.
Don't set IN_ACCESS for unsuccessful reads.
Change "void *" to "volatile TYPE *", improving type safety
and eliminating some warnings (e.g., mp_machdep.c rev 1.106).
cpufunc.h:
Eliminate setbits. As defined, it's not precisely correct;
and it's redundant. (Use atomic_set_int instead.)
ipl_funcs.c:
Use atomic_set_int instead of setbits.
systm.h:
Include atomic.h.
Reviewed by: bde
the loop and not set an error, so we would then try to access an invalid
mbuf...
PR: 12780
Submitted by: bright@rush.net aka zb^3
a new record in length a pr was open... only about a half hour...
critical mbuf fields to sane values. Simplify the use of ETHER_ALIGN to
enforce payload alignment, and turn it on on the x86 as well as alpha
since it helps with NFS which wants the payload to be longword aligned
even though the hardware doesn't require it.
This fixes a problem with the ti driver causing an unaligned access trap
on the Alpha due to m_adj() sometimes not setting the alignment correctly
because of incomplete mbuf initialization.
the driver_t declaration should be "skc" not "sk". Technically, "skc"
is the parent PCI device (the SysKonnect GEnesis controller) and "sk0"
and "sk1" are the network interfaces that get attached to it.
been booted works too -- very neat. However I don't want the system to
stop for 5 seconds when the MII autoprobe is triggered in the xl and
tl drivers since that's lame. Instead, only use the hard delay when
we've been cold booted. If not, use the timeout mechanism instead.
(The SysKonnect driver doesn't use the same autonegotiation scheme, so
no change is required there.)
the device numbers are now minor number only, so that we can still
compare them after dev_t has turned into a blob.
Broken-by: dev_t changes
Reported-by: Vallo Kallaste <vallo@matti.ee>
"Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
When creating new processes (or performing exec), the new page
directory is initialized too early. The kernel might grow before
p_vmspace is initialized for the new process. Since pmap_growkernel
doesn't yet know about the new page directory, it isn't updated, and
subsequent use causes a failure.
The fix is (1) to clear p_vmspace early, to stop pmap_growkernel
from stomping on memory, and (2) to defer part of the initialization
of new page directories until p_vmspace is initialized.
PR: kern/12378
Submitted by: tegge
Reviewed by: dfr
- In isa_dmastart() and isa_dmadone(), cache flush.
- Correct current word register address.
Submitted by (partial): Toshikazu Kaho <kaho@elam.kais.kyoto-u.ac.jp>
by removing a floppy that as being operated on.
The spagghetti is hardly understandable at all anymore, so i can't
100 % ascertain this is really the Right Thing to do, maybe our new
floppy driver maintainer, Jesus Monroy Jr can do this. :-))
numbers that we have been doing in the past, and read /etc/fstab off the
proposed root filesystem to determine the actual device name and vfs
type for the root filesystem. These are then exported to the kernel
via the environment variable vfs.root.mountfrom.
Also includes a workaround fro an apparent chip bug
where UDMA mode 2 can overpower the UDMA engine enough that it will
hog the PCI bus to the exclusion of the processor.
into a loadable module, and all of the platform dependencies are gone
(except for the alpha_XXX_dmamap() thing, which is another issue -- I
still don't know how to use the busdma stuff with a network driver).
Also increase the delay in xl_reset(); testing on a 486/66 with a 3c905C
shows that reading the EEPROM fails immediately after a reset. Waiting
a little longer after the reset completes seems to fix it.
also gets the device by st_rdev, which is alright except for the fact that
the sysctl kern.dumpdev passed out a char device. This is a workaround.
Sorry for not committing the fix earlier, before people started having
problems.
The structure is the right length, but some of the members (notably
wi_q_info) were off a bit. This causes the received signal strength
values to appear bogus.
vnodes referencing this device.
Details:
cdevsw->d_parms has been removed, the specinfo is available
now (== dev_t) and the driver should modify it directly
when applicable, and the only driver doing so, does so:
vn.c. I am not sure the logic in checking for "<" was right
before, and it looks even less so now.
An intial pool of 50 struct specinfo are depleted during
early boot, after that malloc had better work. It is
likely that fewer than 50 would do.
Hashing is done from udev_t to dev_t with a prime number
remainder hash, experiments show no better hash available
for decent cost (MD5 is only marginally better) The prime
number used should not be close to a power of two, we use
83 for now.
Add new checkalias2() to get around the loss of info from
dev2udev() in bdevvp();
The aliased vnodes are hung on a list straight of the dev_t,
and speclisth[SPECSZ] is unused. The sharing of struct
specinfo means that the v_specnext moves into the vnode
which grows by 4 bytes.
Don't use a VBLK dev_t which doesn't make sense in MFS, now
we hang a dummy cdevsw on B/Cmaj 253 so that things look sane.
Storage overhead from all of this is O(50k).
Bump __FreeBSD_version to 400009
The next step will add the stuff needed so device-drivers can start to
hang things from struct specinfo
- Support for setting memory range attributes on SMP systems using the
new SMP rendezvous function
- Don't print the confusing default memory type message.
- Allow legal overlapping range types.
- Turn interrupts back on after setting MTRRs in UP mode (whoops)
- Don't waste time calling invltlb() after wbinvd(); it's not
SMP-compatible (interrupts are off) and unncessary because
wbinvd already flushes the TLB.
This code is now essentially feature-complete.
the caller to specify a function to be guarded between an entry and exit
barrier, as well as pre- and post-barrier functions.
The primary use for this function is synchronised update of per-cpu private
data. The implementation is almost (but not quite) MI; with a better
mechanism for masking per-CPU interrupts it could probably be hoisted.
Reviewed by: peter (partially)
Only know casualy of this is swapinfo/pstat which should be fixes
the right way: Store the actual pathname in the kernel like mount
does. [Volounteers sought for this task]
The road map from here is roughly: expand struct specinfo into struct
based dev_t. Add dev_t registration facilities for device drivers and
start to use them.
but broken, since tsc_timecounter is not initialised in that case,
and updating an uninitialised timecounter is fatal.
Fixed style bugs in the machdep.i8254_freq and machdep.tsc_freq
sysctls.
Reviewed by: phk
used for timecounting. The possible values are the names of the
physically present harware timecounters ("i8254" and "TSC" on i386's).
Fixed some nearby bitrot in comments in <sys/time.h>.
Reviewed by: phk
interrupts that were scheduled. Testing shows it didn't really do very much
and it makes the code a little more complicated (which is never a good thing).
Also fix the rambuffer offset initialization for the 512K/64K SRAM case
(512K total using 64K chips). It should be 0. The only case with a
non-standard rambuffer offset address is 1024K/64K according to the
SysKonnect manual. (My card has the 1024/64 configuration and I don't know
which card uses the 512/64 configuration, if any, so I'm not sure that
this was really a problem for anyone.)
/sys/ddb/db_input.c rev 1.19 to recognize syscons's cursor keycodes.
It is unnecessary now that scgetc() in syscons returns the escape
sequence for the cursor keys rather than their raw, internal key
codes.
been set for a mount point. Insert missing checks to ensure that all
write operations are done asynchronously when the MNT_ASYNC option
has been requested.
Submitted by: Craig A Soules <soules+@andrew.cmu.edu>
Reviewed by: Kirk McKusick <mckusick@mckusick.com>
with respect to interrupts on UP systems. (The upgrade from gcc 2.7.x
to egcs 1.1.2 produced at least one non-atomic code sequence in
swap_pager_getpages.)
In addition, the primitives are now SMP-safe, but only on SMPs. (For
portability between SMPs and UPs, modules are compiled with the SMP-safe
versions.)
Submitted by: dillon and myself
Reviewed by: bde
would make a difference. However, my previous diff _did_ change the
behavior in some way (not necessarily break it), so I'm fixing it.
Found by: bde
Submitted by: bde
Change number of VBI lines from 16 to 12 for NTSC formats.
Juha.Nurmela@quicknet.inet.fi found/fixed bug in VBI_SLEEP.
New features
MSP3430G DBX initialisation from Matt Brown <matt@dqc.org>
STB Bt878 card identification.
Hauppauge Model Number identification.
Changes to probeCard() for better eeprom identification.
Experimental TDA9850 initialisation code, from Linux bttv.
Cross Platform Changes
The driver has been reorgainsed based ideas from Brad Parker's port to Linux
to seperate OS Dependant and Independant sections.
I have backends for FreeBSD 2.2.x/3.x and 4.x newbus, BSDI, OpenBSD and NetBSD.
This commit has FreeBSD 2.2.8/2.2-stable/3.x and FreeBSD 4.x newbus backends.
Some code submitted by: Juha.Nurmela@quicknet.inet.fi
Matt Brown <matt@dqc.org>
Brad Parker <brad@parker.boston.ma.us>
Some code obtained from: Linux bttv driver
vm_map.c:
Don't set OBJ_ONEMAPPING on arbitrary vm objects. Only default
and swap type vm objects should have it set. vm_object_deallocate
already handles these cases.
vm_object.c:
If OBJ_ONEMAPPING isn't already clear in vm_object_shadow,
we are in trouble. Instead of clearing it, make it
an assertion that it is already clear.
1. Printing large quads in small bases overflowed the buffer if
sizeof(u_quad_t) > sizeof(u_long).
2. The sharpflag checks had operator precedence bugs due to excessive
parentheses in all the wrong places.
3. The explicit 0L was bogus in the quad_t comparison and useless in
the long comparision.
4. There was some more bitrot in the comment about ksprintn(). Our
ksprintn() handles bases up to 36 as well as down to 2.
Bruce has other complaints about using %q in kernel and would rather
we went towards using the C9X style %ll and/or %j. (I agree for that
matter, as long as gcc/egcs know how to deal with that.)
Submitted by: bde
not masked during handling of shared PCI interrupts. This resulted in
ASTs sometimes being discarded and softclock interrupts sometimes being
handled prematurely (sometimes = quite often on systems with shared PCI
interrupts, never on other systems).
Debugged by: gibbs and other people at plutotech.com
PR: 6944, maybe 12381
I don't know if it was intentional or not, but it would have printed out:
/compat/linux/foo/bar.so: interpreter not found
If it was, then I've broken it. De-constifying the 'interp' variable
or carrying the constness through to elf_load_file() are alternatives.
Alpha believes that %q is for long long, whereas our quad_t and int64_t
is only just a plain long. long long on the alpha is the same size (64
bit) as a long. It was requested, but I have not implemented yet, support
for C9X style %lld - it should be pretty easy though.
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
large (1G) memory machine configurations. I was able to run 'dbench 32'
on a 32MB system without bring the machine to a grinding halt.
* buffer cache hash table now dynamically allocated. This will
have no effect on memory consumption for smaller systems and
will help scale the buffer cache for larger systems.
* minor enhancement to pmap_clearbit(). I noticed that
all the calls to it used constant arguments. Making
it an inline allows the constants to propogate to
deeper inlines and should produce better code.
* removal of inherent vfs_ioopt support through the emplacement
of appropriate #ifdef's, with John's permission. If we do not
find a use for it by the end of the year we will remove it entirely.
* removal of getnewbufloops* counters & sysctl's - no longer
necessary for debugging, getnewbuf() is now optimal.
* buffer hash table functions removed from sys/buf.h and localized
to vfs_bio.c
* VFS_BIO_NEED_DIRTYFLUSH flag and support code added
( bwillwrite() ), allowing processes to block when too many dirty
buffers are present in the system.
* removal of a softdep test in bdwrite() that is no longer necessary
now that bdwrite() no longer attempts to flush dirty buffers.
* slight optimization added to bqrelse() - there is no reason
to test for available buffer space on B_DELWRI buffers.
* addition of reverse-scanning code to vfs_bio_awrite().
vfs_bio_awrite() will attempt to locate clusterable areas
in both the forward and reverse direction relative to the
offset of the buffer passed to it. This will probably not
make much of a difference now, but I believe we will start
to rely on it heavily in the future if we decide to shift
some of the burden of the clustering closer to the actual
I/O initiation.
* Removal of the newbufcnt and lastnewbuf counters that Kirk
added. They do not fix any race conditions that haven't already
been fixed by the gbincore() test done after the only call
to getnewbuf(). getnewbuf() is a static, so there is no chance
of it being misused by other modules. ( Unless Kirk can think
of a specific thing that this code fixes. I went through it
very carefully and didn't see anything ).
* removal of VOP_ISLOCKED() check in flushbufqueues(). I do not
think this check is necessary, the buffer should flush properly
whether the vnode is locked or not. ( yes? ).
* removal of extra arguments passed to getnewbuf() that are not
necessary.
* missed cluster_wbuild() that had to be a cluster_wbuild_wb() in
vfs_cluster.c
* vn_write() now calls bwillwrite() *PRIOR* to locking the vnode,
which should greatly aid flushing operations in heavy load
situations - both the pageout and update daemons will be able
to operate more efficiently.
* removal of b_usecount. We may add it back in later but for now
it is useless. Prior implementations of the buffer cache never
had enough buffers for it to be useful, and current implementations
which make more buffers available might not benefit relative to
the amount of sophistication required to implement a b_usecount.
Straight LRU should work just as well, especially when most things
are VMIO backed. I expect that (even though John will not like
this assumption) directories will become VMIO backed some point soon.
Submitted by: Matthew Dillon <dillon@backplane.com>
Reviewed by: Kirk McKusick <mckusick@mckusick.com>
clears out the transmit queue and zeroes the downlist pointer register,
but xl_txeof() isn't called before xl_start() tries to queue more packets,
xl_start() will think that the DMA is still in progress and not update
the downlist register again, thus causing packets to sit in the transmit
queue forever.
Patch provided by: Russell T Hunt <alaric@MIT.EDU>
- Correctly observe the variable `extra_history_size' when changing
the size of history (scroll back) buffer.
- Added sc_free_history_buffer().
Pointed out by: des
bit preliminary. It still returns an old-style code arg if SA_SIGINFO
is not set, but I'm not sure of the value of this since the traditional
bsd-style fourth argument (address) is missing.
Also, tidy up a bit of lint.
than a review, this was a nice puzzle.
This is supposed to be binary and source compatible with older
applications that access the old FreeBSD-style three arguments to a
signal handler.
Except those applications that access hidden signal handler arguments
bejond the documented third one. If you have applications that do,
please let me know so that we take the opportunity to provide the
functionality they need in a documented manner.
Also except application that use 'struct sigframe' directly. You need
to recompile gdb and doscmd. `make world` is recommended.
Example program that demonstrates how SA_SIGINFO and old-style FreeBSD
handlers (with their three args) may be used in the same process is at
http://www3.cons.org/tmp/fbsd-siginfo.c
Programs that use the old FreeBSD-style three arguments are easy to
change to SA_SIGINFO (although they don't need to, since the old style
will still work):
Old args to signal handler:
void handler_sn(int sig, int code, struct sigcontext *scp)
New args:
void handler_si(int sig, siginfo_t *si, void *third)
where:
old:code == new:second->si_code
old:scp == &(new:si->si_scp) /* Passed by value! */
The latter is also pointed to by new:third, but accessing via
si->si_scp is preferred because it is type-save.
FreeBSD implementation notes:
- This is just the framework to make the interface POSIX compatible.
For now, no additional functionality is provided. This is supposed
to happen now, starting with floating point values.
- We don't use 'sigcontext_t.si_value' for now (POSIX meant it for
realtime-related values).
- Documentation will be updated when new functionality is added and
the exact arguments passed are determined. The comments in
sys/signal.h are meant to be useful.
Reviewed by: BDE
in ti_rxeof() instead. This doesn't really seem to provide much in the
way of a performance boost, and I'm pretty sure it can cause mbuf leakage
in some extreme cases.
dynamicly linked binaries to run in a chroot'd environment with "emul_path"
as the new root. The new behavior of loading interpreters is identical to the
principle of overlaying.
PR: 10145
into uipc_mbuf.c. This reduces three sets of identical tunable code to
one set, and puts the initialisation with the mbuf code proper.
Make NMBUFs tunable as well.
Move the nmbclusters sysctl here as well.
Move the initialisation of maxsockets from param.c to uipc_socket2.c,
next to its corresponding sysctl.
Use the new tunable macros for the kern.vm.kmem.size tunable (this should have
been in a separate commit, whoops).
print_AMD_info(), L2 internal cache is shown, as are AMD's special CPUID
infos:
CPU: AMD-K6(tm) 3D processor (350.81-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping=12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0x808029bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SYSCALL,PGE,MMX,3DNow!>
PR: kern/12512
Submitted by: Louis A. Mamakos <louie@TransSys.COM>
returns 0 after ptrace() attach and/or detach doesn't quite quite
deliver a signal. Perhaps the process shouldn't be woken in this
case, but avoiding the problem is easy.
PR: 12247
Fixed a couple of places where mechanical fixing of compiler warnings
caused misspelling of NOLOCKF as NULL.
