Commit Graph

723 Commits

Author SHA1 Message Date
mjacob
258c0be375 Harvest one no longer used constant string.
Remove another and place it into play in the
normally ifdef protected zone it would be used
int.

Noticed by:	dim
2013-12-25 04:51:56 +00:00
mav
b5ebe2e35e Use relaxed (write-only) memory barriers when writing some of queue index
registers (for now on ISP2400+).  We never read those registers back and
AFAIK their semantics does not require any immediate reaction on write.
2013-11-10 23:48:16 +00:00
mav
963d7e1a2a Some more registers access optimizations:
- Process ATIO queue only if interrupt status tells so;
 - Do not update queue out pointers after each processed command, do it
only once at the end of the loop.
2013-11-10 23:34:32 +00:00
mav
f3e02a2349 Save one more register read per command by not reading rqstoutrp register
every time.  The purpose of that register is unlikely output queue overflow
detection, so read it only when its last known (and probably stale now)
value signals overflow.

This reduces CPU load and lock congestion and rises bottleneck in CTL
while doing target mode via two 8Gbps ports from 100K to 120K IOPS.
2013-11-10 13:37:44 +00:00
nwhitehorn
14bec3e026 Adjust various SCSI drivers to handle either a 32-bit or 64-bit lun_id_t,
mostly by adjustments to debugging printf() format specifiers. For high
numbered LUNs, also switch to printing them in hex as per SAM-5.

MFC after: 2 weeks
2013-10-30 14:04:47 +00:00
mav
99ff385fd0 Merge CAM locking changes from the projects/camlock branch to radically
reduce lock congestion and improve SMP scalability of the SCSI/ATA stack,
preparing the ground for the coming next GEOM direct dispatch support.

Replace big per-SIM locks with bunch of smaller ones:
 - per-LUN locks to protect device and peripheral drivers state;
 - per-target locks to protect list of LUNs on target;
 - per-bus locks to protect reference counting;
 - per-send queue locks to protect queue of CCBs to be sent;
 - per-done queue locks to protect queue of completed CCBs;
 - remaining per-SIM locks now protect only HBA driver internals.

While holding LUN lock it is allowed (while not recommended for performance
reasons) to take SIM lock.  The opposite acquisition order is forbidden.
All the other locks are leaf locks, that can be taken anywhere, but should
not be cascaded.  Many functions, such as: xpt_action(), xpt_done(),
xpt_async(), xpt_create_path(), etc. are no longer require (but allow) SIM
lock to be held.

To keep compatibility and solve cases where SIM lock can't be dropped, all
xpt_async() calls in addition to xpt_done() calls are queued to completion
threads for async processing in clean environment without SIM lock held.

Instead of single CAM SWI thread, used for commands completion processing
before, use multiple (depending on number of CPUs) threads.  Load balanced
between them using "hash" of the device B:T:L address.

HBA drivers that can drop SIM lock during completion processing and have
sufficient number of completion threads to efficiently scale to multiple
CPUs can use new function xpt_done_direct() to avoid extra context switch.
Make ahci(4) driver to use this mechanism depending on hardware setup.

Sponsored by:	iXsystems, Inc.
MFC after:	2 months
2013-10-21 12:00:26 +00:00
mav
c13057cda9 Partial MFproject/camlock r256671:
Fix several target mode SIMs to not blindly clear ccb_h.flags field of
ATIO CCBs.  Not all CCB flags there belong to them.
2013-10-21 06:04:39 +00:00
mav
15c0a70328 Optimize isp(4) to reduce CPU usage, especially in target mode:
- Remove two excessive and slow register reads from isp_intr().  Instead
of rereading value every time, assume that registers contain what we have
written there.
 - Avoid sequential search through 4096 array elements when looking for
command tag.  Use hash of lists to store active tags separately from free
ones and so greatly speedup the searches.

Reviewed by:	mjacob
2013-10-17 20:19:15 +00:00
ken
c6e2041529 Export the maxio field in the CAM XPT_PATH_INQ CCB in the isp(4)
driver.

This tells consumers up the stack the maximum I/O size that the
controller can handle.

The I/O size is bounded by the number of scatter/gather segments
the controller can handle and the page size.  For an amd64 system,
it works out to around 5MB.

Reviewed by:	mjacob
MFC after:	3 days
Sponsored by:	Spectra Logic
2013-08-15 16:41:27 +00:00
scottl
28bd1409da Update PCI drivers to no longer look at the MEMIO-enabled bit in the PCI
command register.  The lazy BAR allocation code in FreeBSD sometimes
disables this bit when it detects a range conflict, and will re-enable
it on demand when a driver allocates the BAR.  Thus, the bit is no longer
a reliable indication of capability, and should not be checked.  This
results in the elimination of a lot of code from drivers, and also gives
the opportunity to simplify a lot of drivers to use a helper API to set
the busmaster enable bit.

This changes fixes some recent reports of disk controllers and their
associated drives/enclosures disappearing during boot.

Submitted by:	jhb
Reviewed by:	jfv, marius, achadd, achim
MFC after:	1 day
2013-08-12 23:30:01 +00:00
mjacob
2bf9d2e61f When fiddling with options of which registers to copy out for
a mailbox command and which registers to copy back in when
the command completes, the bits being set need to not only
specify what bits you want to add from the default from the
table but also what bits you want *subtract* (mask) from the
default from the table.

A failing ISP2200 command pointed this out.

Much appreciation to: marius, who persisted and narrowed down what
the failure delta was, and shamed me into actually fixing it.
MFC after:	1 week
2013-07-13 21:24:25 +00:00
marius
36c9d501f0 Flag isp(4) as supporting unmapped I/O; all necessary conversion actually
already has been done as part of r246713.

Reviewed by:	mjacob
2013-06-04 11:05:57 +00:00
mav
3d32e6b10c MFprojects/camlock r248982:
Stop abusing xpt_periph in random plases that really have no periph related
to CCB, for example, bus scanning.  NULL value is fine in such cases and it
is correctly logged in debug messages as "noperiph".  If at some point we
need some real XPT periphs (alike to pmpX now), quite likely they will be
per-bus, and not a single global instance as xpt_periph now.
2013-04-14 09:55:48 +00:00
mjacob
713f357457 Remove redundant xpt_alloc_ccb in isp_target_thread that was causing leakage.
Pointed out by:	Sascha Wildner of DragonFly BSD
MFC after:	1 week
2013-02-26 21:37:12 +00:00
mjacob
75d62de01a Turn off fast posting for the ISP2100- I'd forgotten that it actually
might have been enabled for them- now that we use all 32 bits of handle.
Fast Posting doesn't pass the full 32 bits.

Noticed by: Bugs in NetBSD. Only a NetBSD user might actually still use such old hardware.
MFC after:	1 week
2013-02-25 11:22:54 +00:00
kib
bd7f0fa0bb Reform the busdma API so that new types may be added without modifying
every architecture's busdma_machdep.c.  It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code.  The MD busdma is then given a chance to do any final processing
in the complete() callback.

The cam changes unify the bus_dmamap_load* handling in cam drivers.

The arm and mips implementations are updated to track virtual
addresses for sync().  Previously this was done in a type specific
way.  Now it is done in a generic way by recording the list of
virtuals in the map.

Submitted by:	jeff (sponsored by EMC/Isilon)
Reviewed by:	kan (previous version), scottl,
	mjacob (isp(4), no objections for target mode changes)
Discussed with:	     ian (arm changes)
Tested by:	marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
	amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
2013-02-12 16:57:20 +00:00
mjacob
b52d67ff65 Don't allow for more than one segment for the control space since
we're not set up to deal with that.

X-MFC:	242479
MFC after:	1 week
2012-11-02 14:38:57 +00:00
mjacob
1e90b219ab Don't allow for more than one segment for the control space since
we're not set up to deal with that.

MFC after:	1 week
2012-11-02 14:37:21 +00:00
mjacob
0a5ee7e646 Minor correction.
MFC after:	1 day
2012-09-17 02:50:16 +00:00
mjacob
f566f6b120 Add some edits to the changed comments so that they make more sense.
MFC after:	1 day
2012-09-17 02:49:02 +00:00
eadler
8600cbb5b6 Correct double "the the"
Approved by:	cperciva
MFC after:	3 days
2012-09-14 21:28:56 +00:00
mjacob
241b954939 Remove useless extra test.
Pointed out by:	Sascha of DragonFly BSD
MFC after:	2 weeks
2012-09-07 22:45:31 +00:00
mjacob
1db52193bc Remove dependence on MAXPHYS.
MFC after:	1 month
2012-08-21 16:18:11 +00:00
mjacob
6c14ae3c13 On lun disable, complete all INOTs and ATIOs with CAM_REQ_ABORTED.
Reviewed by:	ken (silently), chuck
MFC after:	3 weeks
2012-08-16 15:32:16 +00:00
mjacob
ee01bf1d75 Remove extraneous newline.
MFC after:	1 month
2012-08-12 20:49:25 +00:00
mjacob
c0bff9b6e5 Fix an oops where we wiped out DMA maps. Don't allocate extended
command space for anything less than a 2300.

MFC after:	1 month
X-MFC:		238869
2012-08-12 20:45:47 +00:00
mjacob
1587b88eab More rototilling with target mode in an attemp to get multiple
CCB at a time outstanding reliable. It's not there yet, but this
is the direction to go in so might as well commit. So far,
multiple at a time CCBs work (see ISP_INTERNAL_TARGET test mode),
but it fails if there are more downstream than the SIM wants
to handle and SRR is sort of confused when this happens, plus
it is not entirely quite clear what one does if a CCB/CTIO fails
and you have more in flight (that don't fail, say) and more queued
up at the SIM level that haven't been started yet.

Some of this is driven because there apparently is no flow control
to requeue XPT_CONTINUE_IO requests like there are for XPT_SCSI_IO
requests. It is also more driven in that the few target mode
periph drivers there are are not really set up for handling pushback-
heck most of them don't even check for errors (and what would they
really do with them anyway? It's the initiator's problem, really....).

The data transfer arithmetic has been worked over again to handle
multiple outstanding commands, so you have a notion of what's been
moved already as well as what's currently in flight. It turns that
this led to uncovering a REPORT_LUNS bug in the ISP_INTERNAL_TARGET
code which was sending back 24 bytes of rpl data instead of the
specified 16. What happened furthermore here is that sending back
16 bytes and reporting an overrun of 8 bytes made the initiator
(running FC-Tape aware f/w) mad enough to request, and keep
requesting, another FCP response (I guess it didn't like the answer
so kept asking for it again).

Sponsored by: Spectralogic
MFC after:	1 month
2012-08-08 18:24:33 +00:00
mjacob
1f063923e4 Add detach logic to SBus variant.
Obtained from:	Marius
MFC after:	1 month
2012-08-04 00:00:30 +00:00
mjacob
553b289506 Oops. We only do allocate room for extended commands
and responses for 2300 cards are newer.

Sponsored by:	Spectralogic
Noticed by:	Our Friend Manfred
MFC after:	1 month
X-MFC: 238869
2012-08-03 14:25:35 +00:00
mjacob
debac64ecc Grr.!$()!$$ I missed checking this in even though I *did* run
a tinderbox myself and caught the error.

Change to isp_send_cmd needs a final ecmd argument.

Sponsored by: Spectralogic
MFC after:	1 month
X-MFC: 238869
2012-07-29 14:21:42 +00:00
mjacob
a41cb450d6 -----------
MISC CHANGES

Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee
eventual delivery of a NOTIFY ACK. This is tons better than just
ignoring the return from isp_notify_ack and hoping for the best.

Clean up the lower level lun enable code to be a bit more sensible.

Fix a botch in isp_endcmd which was messing up the sense data.

Fix notify ack for SRR to use a sensible error code in the case
of a reject.

Clean up and make clear what kind of firmware we've loaded and
what capabilities it has.
-----------
FULL (252 byte) SENSE DATA

In CTIOs for the ISP, there's only a limimted amount of space
to load SENSE DATA for associated CHECK CONDITIONS (24 or 26
bytes). This makes it difficult to send full SENSE DATA that can
be up to 252 bytes.

Implement MODE 2 responses which have us build the FCP Response
in system memory which the ISP will put onto the wire directly.

On the initiator side, the same problem occurs in that a command
status response only has a limited amount of space for SENSE DATA.
This data is supplemented by status continuation responses that
the ISP pushes onto the response queue after the status response.
We now pull them all together so that full sense data can be
returned to the periph driver.

This is supported on 23XX, 24XX and 25XX cards.

This is also preparation for doing >16 byte CDBs.

-----------
FC TAPE

Implement full FC-TAPE on both initiator and target mode side.  This
capability is driven by firmware loaded, board type, board NVRAM
settings, or hint configuration options to enable or disable. This
is supported for 23XX, 24XX and 25XX cards.

On the initiator side, we pretty much just have to generate a command
reference number for each command we send out. This is FCP-4 compliant
in that we do this per ITL nexus to generate the allowed 1 thru 255
CRN.

In order to support the target side of FC-TAPE, we now pay attention
to more of the PRLI word 3 parameters which will tell us whether
an initiator wants confirmed responses. While we're at it, we'll
pay attention to the initiator view too and report it.

On sending back CTIOs, we will notice whether the initiator wants
confirmed responses and we'll set up flags to do so.

If a response or data frame is lost the initiator sends us an SRR
(Sequence Retransmit Request) ELS which shows up as an SRR notify
and all outstanding CTIOs are nuked with SRR Received status. The
SRR notify contains the offset that the initiator wants us to restart
the data transfer from or to retransmit the response frame.

If the ISP driver still has the CCB around for which the data segment
or response applies, it will retransmit.

However, we typically don't know about a lost data frame until we
send the FCP Response and the initiator totes up counters for data
moved and notices missing segments. In this case we've already
completed the data CCBs already and sent themn back up to the periph
driver.  Because there's no really clean mechanism yet in CAM to
handle this, a hack has been put into place to complete the CTIO
CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA
POINTER extended message in it. The internal ISP target groks this
and ctl(8) will be modified to deal with this as well.

At any rate, the data is retransmitted and an an FCP response is
sent. The whole point here is to successfully complete a command
so that you don't have to depend on ULP (SCSI) to have to recover,
which in the case of tape is not really possible (hence the name
FC-TAPE).

Sponsored by: Spectralogic
MFC after:	1 month
2012-07-28 20:06:29 +00:00
brueffer
f0466ef5bb Fix typo in a message.
Obtained from:	DragonFly BSD (change 7a817ab191e4898404a9037c55850e47d177308c)
MFC after:	3 days
2012-07-15 14:40:49 +00:00
mjacob
fff8cc103a Unbreak register tests for parallel SCSI.
You can't overwrite registers 7 and 8.
MFC after:	3 days
2012-06-25 03:06:29 +00:00
mjacob
68a4606283 Clean up multi-id mode so it's driven by the f/w loaded,
not by some hint setting.  Do more preparations for FC-Tape.
Clean up resource counting for 24XX or later chipsets so
we find out after EXEC_FIRMWARE what is actually supported.
Set target mode exchange count based upon whether or not
we are supporting simultaneous target/initiator mode. Clean
up some old (pre-24XX) xfwoption and zfwoption issues.

Sponsored by:	Spectralogic
MFC after:	3 days
2012-06-24 17:30:54 +00:00
mjacob
7d8c797417 Prepare for FC-Tape support. This involved doing a lot of little cleanups
and crosschecks against firmware documentation. We now check and report
FC firmware attributes and at least are now prepared for the upper 48 bits
of f/w attributes (which are probably for the 8100 or later cards). This
involed changing how inbits and outbits are calculated for varios commands,
hopefully clearer and cleaner. This also caused me to clean up the actual
mailbox register usage. Finally, we are now unconditionally using a CRN
for initiator mode.

A longstanding issue with the 2400/2500 is that they do *not* support
a "Prefer PTP followed by loop", which explains why enabling that
caused the f/w to crash.

A slightly more invasive change is to let the firmware load entirely
drive whether multi_id support is enabled or not.

Sponsored by:	Spectralogic
MFC after:	1 week
2012-06-17 21:39:40 +00:00
mjacob
5328dda9e8 If debug values were set, the default from tval floated
down and triggered an attempt to set multiple virtual
ports whether you wanted them or not.

MFC after:	3 days
2012-06-15 15:28:15 +00:00
mjacob
668ec8ec8c Clean up and complete the incomplete deferred enable code.
Make the default role NONE if target mode is selected. This
allows ctl(8) to switch to/from target mode via knob settings.
If we default to role 'none', this causes a reset of the
24XX f/w which then causes initiators to wake up and notice
when we come online.

Reviewed by:    kdm
MFC after:      2 weeks
Sponsored by:   Spectralogic
2012-06-01 23:29:48 +00:00
eadler
9463606153 Adding missing dependancies for loading hptiop(4), hptmv(4) and isp(4) as modules.
PR:		kern/166239
Submitted by:	Pavel Timofeev <timp87@gmail.com>
Discussed on:	-stable, -scsi
Reviewed by:	scottl
No objection from: mjacob
Approved by:	cperciva
MFC after:	3 days
2012-06-01 04:34:49 +00:00
kevlo
6989e38153 Fix memset sizeof 2012-02-22 01:08:59 +00:00
mjacob
e3a2ce835d Fix target mode compilation issues that arose after a change
in the sense data structures.

MFC after:	1 week
2011-12-27 14:59:24 +00:00
mav
b2bc09ab33 Fix few bugs in isp(4) target mode support:
- in destroy_lun_state() assert hold == 1 instead of 0, as it should
receive hold taken by the create_lun_state() or get_lun_statep() before;
 - fix hold count leak inside rls_lun_statep() that also fired above assert;
 - in destroy_lun_state() use SIM bus number instead of SIM path id for
ISP_GET_PC_ADDR(), as it was before r196008;
 - make isp_disable_lun() to set status in CCB;
 - make isp_target_mark_aborted() set status into the proper CCB.

Reviewed by:	mjacob
Sponsored by:	iXsystems, inc.
MFC after:	1 month
2011-12-13 09:58:05 +00:00
mjacob
0aecd21699 Was chasing down a failure to load f/w on a 2400. It turns out that the card
is actually broken, or needs a BIOS upgrade for 64 bit loads, but this uncovered
a couple of misplaced opcode definitions and some missing continual mbox command
cases, so might as well update them here.
2011-11-16 02:52:24 +00:00
eadler
8710aaed7e - add a missing "be" and "in"
- fix other errors introduced when committing r226436
- add 'function' to a sentence where it makes sense

Submitted by:	delphij
Submitted by:	dougb
Submitted by:	jhb
Approved by:	dougb
Approved by:	jhb
2011-11-11 22:27:09 +00:00
mjacob
3230b890d9 Implement the sysctl's for fibre channel that are listed in the man page.
MFC after:	3 days
2011-11-06 00:44:40 +00:00
eadler
9d7884364e - change "is is" to "is" or "it is"
- change "the the" to "the"

Approved by:	lstewart
Approved by:	sahil (mentor)
MFC after:	3 days
2011-10-16 14:30:28 +00:00
marius
7a6e7c47a2 Sync with ahc(4)/ahd(4)/sym(4) etc:
Zero any sense not transferred by the device as the SCSI specification
mandates that any untransferred data should be assumed to be zero.

Reviewed by:	ken
2011-10-07 21:23:42 +00:00
ken
949394e8e0 Add descriptor sense support to CAM, and honor sense residuals properly in
CAM.

Desriptor sense is a new sense data format that originated in SPC-3.  Among
other things, it allows for an 8-byte info field, which is necessary to
pass back block numbers larger than 4 bytes.

This change adds a number of new functions to scsi_all.c (and therefore
libcam) that abstract out most access to sense data.

This includes a bump of CAM_VERSION, because the CCB ABI has changed.
Userland programs that use the CAM pass(4) driver will need to be
recompiled.

camcontrol.c:	Change uses of scsi_extract_sense() to use
		scsi_extract_sense_len().

		Use scsi_get_sks() instead of accessing sense key specific
		data directly.

scsi_modes:	Update the control mode page to the latest version (SPC-4).

scsi_cmds.c,
scsi_target.c:	Change references to struct scsi_sense_data to struct
		scsi_sense_data_fixed.  This should be changed to allow the
		user to specify fixed or descriptor sense, and then use
		scsi_set_sense_data() to build the sense data.

ps3cdrom.c:	Use scsi_set_sense_data() instead of setting sense data
		manually.

cam_periph.c:	Use scsi_extract_sense_len() instead of using
		scsi_extract_sense() or accessing sense data directly.

cam_ccb.h:	Bump the CAM_VERSION from 0x15 to 0x16.  The change of
		struct scsi_sense_data from 32 to 252 bytes changes the
		size of struct ccb_scsiio, but not the size of union ccb.
		So the version must be bumped to prevent structure
		mis-matches.

scsi_all.h:	Lots of updated SCSI sense data and other structures.

		Add function prototypes for the new sense data functions.

		Take out the inline implementation of scsi_extract_sense().
		It is now too large to put in a header file.

		Add macros to calculate whether fields are present and
		filled in fixed and descriptor sense data

scsi_all.c:	In scsi_op_desc(), allow the user to pass in NULL inquiry
		data, and we'll assume a direct access device in that case.

		Changed the SCSI RESERVED sense key name and description
		to COMPLETED, as it is now defined in the spec.

		Change the error recovery action for a number of read errors
		to prevent lots of retries when the drive has said that the
		block isn't accessible.  This speeds up reconstruction of
		the block by any RAID software running on top of the drive
		(e.g. ZFS).

		In scsi_sense_desc(), allow for invalid sense key numbers.
		This allows calling this routine without checking the input
		values first.

		Change scsi_error_action() to use scsi_extract_sense_len(),
		and handle things when invalid asc/ascq values are
		encountered.

		Add a new routine, scsi_desc_iterate(), that will call the
		supplied function for every descriptor in descriptor format
		sense data.

		Add scsi_set_sense_data(), and scsi_set_sense_data_va(),
		which build descriptor and fixed format sense data.  They
		currently default to fixed format sense data.

		Add a number of scsi_get_*() functions, which get different
		types of sense data fields from either fixed or descriptor
		format sense data, if the data is present.

		Add a number of scsi_*_sbuf() functions, which print
		formatted versions of various sense data fields.  These
		functions work for either fixed or descriptor sense.

		Add a number of scsi_sense_*_sbuf() functions, which have a
		standard calling interface and print the indicated field.
		These functions take descriptors only.

		Add scsi_sense_desc_sbuf(), which will print a formatted
		version of the given sense descriptor.

		Pull out a majority of the scsi_sense_sbuf() function and
		put it into scsi_sense_only_sbuf().  This allows callers
		that don't use struct ccb_scsiio to easily utilize the
		printing routines.  Revamp that function to handle
		descriptor sense and use the new sense fetching and
		printing routines.

		Move scsi_extract_sense() into scsi_all.c, and implement it
		in terms of the new function, scsi_extract_sense_len().
		The _len() version takes a length (which should be the
		sense length - residual) and can indicate which fields are
		present and valid in the sense data.

		Add a couple of new scsi_get_*() routines to get the sense
		key, asc, and ascq only.

mly.c:		Rename struct scsi_sense_data to struct
		scsi_sense_data_fixed.

sbp_targ.c:	Use the new sense fetching routines to get sense data
		instead of accessing it directly.

sbp.c:		Change the firewire/SCSI sense data transformation code to
		use struct scsi_sense_data_fixed instead of struct
		scsi_sense_data.  This should be changed later to use
		scsi_set_sense_data().

ciss.c:		Calculate the sense residual properly.  Use
		scsi_get_sense_key() to fetch the sense key.

mps_sas.c,
mpt_cam.c:	Set the sense residual properly.

iir.c:		Use scsi_set_sense_data() instead of building sense data by
		hand.

iscsi_subr.c:	Use scsi_extract_sense_len() instead of grabbing sense data
		directly.

umass.c:	Use scsi_set_sense_data() to build sense data.

		Grab the sense key using scsi_get_sense_key().

		Calculate the sense residual properly.

isp_freebsd.h:	Use scsi_get_*() routines to grab asc, ascq, and sense key
		values.

		Calculate and set the sense residual.

MFC after:	3 days
Sponsored by:	Spectra Logic Corporation
2011-10-03 20:32:55 +00:00
mjacob
d7243f9f08 Most of these changes to isp are to allow for isp.ko unloading.
We also revive loop down freezes. We also externaliz within isp
isp_prt_endcmd so something outside the core module can print
something about a command completing. Also some work in progress to
assist in handling timed out commands better.

Partially Sponsored by: Panasas
Approved by:	re (kib)
MFC after:	1 month
2011-08-13 23:34:17 +00:00
mjacob
ab2936096f Fixes zombie device and loop down timers so that they work more than
once. Use taskqueues to do the actual work.

Fix an offset line.

Fix isp_prt so that prints from just one buffer, which makes it
appear cleanly cleanly in logs on SMP systems.

Approved by:	re (kib)
MFC after:	1 month
2011-08-12 19:51:28 +00:00
mjacob
c922219ced Add support QLE220 card- an 2500 lookalike.
Obtained mostly from:	Roman && Konstantin
MFC after:	1 week
2011-03-10 23:53:01 +00:00