The goal of this change is to fix a problem with PCI shared interrupts
during suspend and resume.
I have observed a couple of variations of the following scenario.
Devices A and B are on the same PCI bus and share the same interrupt.
Device A's driver is suspended first and the device is powered down.
Device B generates an interrupt. Interrupt handlers of both drivers are
called. Device A's interrupt handler accesses registers of the powered
down device and gets back bogus values (I assume all 0xff). That data is
interpreted as interrupt status bits, etc. So, the interrupt handler
gets confused and may produce some noise or enter an infinite loop, etc.
This change affects only PCI devices. The pci(4) bus driver marks a
child's interrupt handler as suspended after the child's suspend method
is called and before the device is powered down. This is done only for
traditional PCI interrupts, because only they can be shared.
At the moment the change is only for x86.
Notable changes in core subsystems / interfaces:
- BUS_SUSPEND_INTR and BUS_RESUME_INTR methods are added to bus
interface along with convenience functions bus_suspend_intr and
bus_resume_intr;
- rman_set_irq_cookie and rman_get_irq_cookie functions are added to
provide a way to associate an interrupt resource with an interrupt
cookie;
- intr_event_suspend_handler and intr_event_resume_handler functions
are added to the MI interrupt handler interface.
I added two new interrupt handler flags, IH_SUSP and IH_CHANGED, to
implement the new intr_event functions. IH_SUSP marks a suspended
interrupt handler. IH_CHANGED is used to implement a barrier that
ensures that a change to the interrupt handler's state is visible
to future interrupts.
While there, I fixed some whitespace issues in comments and changed a
couple of logically boolean variables to be bool.
MFC after: 1 month (maybe)
Differential Revision: https://reviews.freebsd.org/D15755
It has been reported that on some systems (with real hardware passed
through to a virtual machine) the WP detection causes USB disk probing
failures.
While here, also fix the selection of the next state in the case
of malloc failure in DA_STATE_PROBE_WP. It was DA_STATE_PROBE_RC
unconditionally even when it should have been DA_STATE_PROBE_RC16.
PR: 225794
Reported by: David Boyd <David.Boyd49@twc.com>
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D18496
or the likes. Add new control message types: setdlt and getdlt to switch
from default DLT_RAW (no encapsulation) to DLT_EN10MB (ethernet).
Approved by: glebius
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D18535
With r342151 I did fix the BIOS version of zfs_probe_dev() from accessing
the whole disk, but the fix was not complete - we actually did not check
if the device name was really for whole disk. Since UEFI version
is only calling the zfs_probe_dev() with partitions and not with whole
disk, the UEFI loader was not able to find the zfs pools.
This update does correct the issue by calling archsw.arch_getdev() to
translate the device name back to dev_desc, and we have whole disk when both
partition and slice values are -1.
Reported by: alvisen_gmail.com
Differential Revision: https://reviews.freebsd.org/D18558
/usr/sbin/audit(dist)?d are only installed if ${MK_AUDIT} == yes. Their
supporting scripts should only be installed in those instances as well.
Submitted by: ngie
Reviewed by: emaste
MFC after: 2 weeks
Pull Request: https://github.com/freebsd/freebsd/pull/242
First of all, normal setups can not boot such pools as the tools
do not support installing boot programs.
Secondly, for proper pool configuration detection, we need to checks all
four label copies on disk, 2 from front and 2 from the end of the disk,
but zfs label does not contain the size of the disk - so we depend on
firmware to report the correct disk size or use information from the
partition table.
Without partition table, we only can rely on firmware to report and support
disk IO properly.
There is a specific case: 8TB disks are reported by BIOS to have 4294967295
sectors (0x00000000ffffffff), the sectors reported by OS is 15628053168
(0x00000003a3812ab0), so the reported size is less than actual but is hitting
32-bit max. Unfortuantely the real limit must be even lower because probing
this disk in this system will wnd up with hung system.
UEFI boot of this system seems not to be affected.
Reviewed by: imp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18558
on bsdinstall(8) and may be non-functional
for system built WITHOUT_BSDINSTALL. (*)
Also, add a check for jails sharing whole tree with host (path=/)
and do not skip it.
Reported by: Andre.Albsmeier@siemens.com (*)
MFC after: 1 week
check-hash fails. Panic'ing is not an appropriate response. So, check
for an error return from VFS_ROOT() and when an error is reported,
unwind and return the error.
Reported by: Gary Jennejohn (gj)
Sponsored by: Netflix
the check-hash fails. Prior to the fix in -r342133 the inode with the
zeroed out check-hash was written back to disk causing further confusion.
Reported by: Gary Jennejohn (gj)
Sponsored by: Netflix
before copying in the inode so that the mode and link-count are not set
if the check-hash fails. This change ensures that the vnode will be properly
unwound and recycled rather than being held in the cache.
Initialize the file mode is zero so that if the loading of the inode
fails (for example because of a check-hash failure), the vnode will be
properly unwound and recycled.
Reported by: Gary Jennejohn (gj)
Sponsored by: Netflix
"panic: softdep_update_inodeblock: bad link count" when releasing
a partially initialized vnode after an inode check-hash failure.
Reported by: Gary Jennejohn <gljennjohn@gmail.com>
Reported by: Peter Holm (pho)
Sponsored by: Netflix
If requested to fix the inode check-hash it would confirm having done
it, but then fail to make the fix. The same code is used in fsdb which,
unlike fsck, would actually fix the inode check-hash.
The discrepancy occurred because fsck has two ways to fetch inodes.
The inode by number function ginode() and the streaming inode
function getnextinode() used during pass1. Fsdb uses the ginode()
function which correctly does the fix, while fsck first encounters
the bad inode check-hash in pass1 where it is using the getnextinode()
function that failed to make the correction. This patch corrects
the getnextinode() function so that fsck now correctly fixes inodes
with incorrect inode check-hashs.
Reported by: Gary Jennejohn <gljennjohn@gmail.com>
Sponsored by: Netflix
This change is causing TCP connections using cubic to hang. Need to dig more to
find exact cause and fix it.
Reported by: tj at mrsk dot me, Matt Garber (via twitter)
Discussed with: sbruno (previously), allanjude, cperciva
MFC after: 3 days
The removal (and creation of a port) has been pre-announced in UPDATING
1 month ago. Packages are available for all supported FreeBSD vesions.
I did not think that another entry in UPDATING is required to note the
actual removal.
No MFC is planned - CTM shall be kept in base for all releases up to 12.x.
Reviewed by: rgrimes
Approved by: imp, bcr (manpages)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D17935
Use the sysctl_handle_int() handler to write out the old value and read
the new value into a temporary variable. Use the temporary variable
for any checks of values rather than using the CAST_PTR_INT() macro on
req->newptr. The prior usage read directly from userspace memory if the
sysctl() was called correctly. This is unsafe and doesn't work at all on
some architectures (at least i386.)
In some cases, the code could also be tricked into reading from kernel
memory and leaking limited information about the contents or crashing
the system. This was true for CDG, newreno, and siftr on all platforms
and true for i386 in all cases. The impact of this bug is largest in
VIMAGE jails which have been configured to allow writing to these
sysctls.
Per discussion with the security officer, we will not be issuing an
advisory for this issue as root access and a non-default config are
required to be impacted.
Reviewed by: markj, bz
Discussed with: gordon (security officer)
MFC after: 3 days
Security: kernel information leak, local DoS (both require root)
Differential Revision: https://reviews.freebsd.org/D18443
7.0.1 release r349250. There were no functional changes since the 7.0.1
rc3 import.
PR: 230240, 230355
Relnotes: yes
MFC after: 2 months
X-MFC-With: r341825
This can drastically lower the load on gssd(8) on large NFS servers.
Submitted by: Per Andersson <pa at chalmers dot se>
Reviewed by: rmacklem@
MFC after: 2 weeks
Sponsored by: Chalmers University of Technology
Differential Revision: https://reviews.freebsd.org/D18393
The original code did not support dynamically loaded libraries and used
suboptimal access to TLS variables.
New implementation removes lazy resolving of TLS relocation - due to flaw
in TLSDESC design is impossible to switch resolver function at runtime
without expensive locking.
Due to this, 3 specialized resolvers are implemented:
- load time resolver for TLS relocation from libraries loaded with main
executable (thus with known TLS offset).
- resolver for undefined thread weak symbols.
- slower lazy resolver for dynamically loaded libraries with fast path for
already resolved symbols.
PR: 228892, 232149, 233204, 232311
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18417
PR: maybe related to 233998 (inconclusive at this time)
Submitted by: byuu <byuu AT tutanota.com> (previous version)
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D18506
This fixes building in CheriBSD with a strict tmp path since we don't
bootstrap a cpp but pass the full path to clang-cpp instead.
While touching this file also fix all shellcheck warnings in make_dtb.sh.
Reviewed By: manu
Differential Revision: https://reviews.freebsd.org/D18376
MacOS/Linux do not define struct cmsgcred but we need to bootstrap libnv
when building on non-FreeBSD systems. Since they are not used during
bootstrap we can just omit these two functions there.
Reviewed By: emaste
Differential Revision: https://reviews.freebsd.org/D18472
- Panic immediately if witness says we're holding non-sleepable locks.
This helps ensure that we don't recurse on the pmap lock in
pmap_fault_fixup().
- Panic if the kernel faults on a user address without setting an
onfault handler.
- Panic if the fault occurred in a critical section or interrupt
handler, like we do on other platforms.
- Fix some style issues in trap_pfault().
Reviewed by: jhb
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18561
pmap_remove_pages() is called during process termination, when it is
guaranteed that no other CPU may access the mappings being torn down.
In particular, it unnecessary to invalidate each mapping individually
since we do a pmap_invalidate_all() at the end of the function.
Also don't call pmap_invalidate_all() while holding a PV list lock, the
global pvh lock is sufficient.
Reviewed by: jhb
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18562
pmaps on RISC-V always have an L1 page table page, so we don't need to
check for this when performing lookups.
Reviewed by: jhb
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18563
fcmpset returns true/false as a int, so make the return types and
variables match the int to be consistent with other arch.
Reviewed by: cognet@
Differential Revision: https://reviews.freebsd.org/D18557
- Build up phys_avail[] in a single loop, excluding memory used by
the loaded kernel.
- Fix an array indexing bug in the aforementioned phys_avail[]
initialization.[1]
- Remove some unneeded code copied from the arm64 implementation.
PR: 231515 [1]
Reviewed by: jhb
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18464
