Clarify some statements around PMTUD blackhole detection to make
the behavior more clear in the man page.
Submitted by: Mikhail <mp@lenta.ru>
MFC after: 2 weeks
rtld-elf for powerpc 32 bit:
libexec/rtld-elf/powerpc/reloc.c:486:6: error: taking the absolute value of unsigned type 'Elf_Addr' (aka 'unsigned int') has no effect [-Werror,-Wabsolute-value]
if (abs(offset) < 32*1024*1024) { /* inside 32MB? */
^
libexec/rtld-elf/powerpc/reloc.c:486:6: note: remove the call to 'abs' since unsigned values cannot be negative
if (abs(offset) < 32*1024*1024) { /* inside 32MB? */
^~~
1 error generated.
Cast 'offset' to int, since that was intended, and should be safe to do
on architectures with 32-bit two's complement ints.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D1387
initially set up the MMU. Some day they may also be useful as part of
suspend/resume handling, when we get better at power management.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>,
Michal Meloun <meloun@miracle.cz
are inline functions that handle all the routine maintenance operations
except the flush-all and invalidate-all routines which are required only
during early kernel init.
These inline functions should be very much faster than the old mechanism
that involved jumping through the big cpufuncs table, especially for
common operations such as invalidating a single TLB entry. Note that
nothing is calling these yet, this just is just required infrastructure
for upcoming changes to the pmap-v6 code.
mechanism defined for armv7 (and also present on some armv6 chips including
the arm1176 used on rpi). The information is parsed into a global cpuinfo
structure, which will be used by (upcoming) new cache and tlb maintenance
code to handle cpu-specific variations of the maintence sequences.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>,
Michal Meloun <meloun@miracle.cz
Summary:
PowerPC64 uses function descriptors in a section .opd, exporting the descriptors
to the symbol table. This adds support for these into dt_link.c so that dtrace
USDT probes can be compiled.
Test Plan:
Tested only on powerpc64. No regression testing has been performed, so I want
someone with x86 hardware to regression test this.
Tested on amd64 by markj
Reviewers: #dtrace, markj
Reviewed By: #dtrace, markj
Subscribers: markj
Differential Revision: https://reviews.freebsd.org/D1267
MFC after: 3 weeks
OpenBSD guests always enable "special mask mode" during boot. As a result of
r275952 this is flagged as an error and the guest cannot boot.
Reviewed by: grehan
Differential Revision: https://reviews.freebsd.org/D1384
MFC after: 1 week
setting call gate, which must be 64 bit, put a code segment descriptor
into ldt slot 0.
This way, syscall shim does not switch temporary to 64bit trampoline,
and does not create a window where signal delivery interrupts 64 bit
mode (signal handler cannot return). The cost is shim running with
non-zero based segment in %cs, which requires vfork() handling make
more assumptions.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
- Simplify MSI allocation to what is actually needed for a single one.
- Release the MSI and the corresponding bus resource as appropriate when
either the interrupt resource cannot be allocated or setting up the
interrupt fails.
- Error out when interrupt allocation or setup fails and polling is
disabled.
- Release the MSI after the corresponding bus resource so the former is
not leaked on detach.
- Remove a redundant softc member.
MFC after: 3 days
images into the kernel as currently included into iwn6000g2{a,b}fw.ko
and delete the old files, missed in r254199 and r259135 respectively.
MFC after: 3 days
for the lookup.
- For devices affected by PCI_QUIRK_MSI_INTX_BUG, ensure PCIM_CMD_INTxDIS
is cleared when using MSI/MSI-X.
- Employ PCI_QUIRK_MSI_INTX_BUG for BCM5714(S)/BCM5715(S)/BCM5780(S) rather
than clearing PCIM_CMD_INTxDIS unconditionally for all devices in bge(4).
MFC after: 3 days
macro wasn't needed and was being used with swapped arguments which always
give the same result (0) defeating the overflow check.
On initialization, do not use bcm_mbox_intr() to read the pending messages,
with the new semaphore based implementation this will lead to semaphore
being incremented on the channels that contain pending data and will make
the first read for that channel return stale data.
This fixes the hang that happens on boot while initializing the cpufreq on
Raspberry Pi.
so take this into account when iterating over DOF tables.
PR: 195555
Submitted by: Fedor Indutny <fedor@indutny.com> (original version)
MFC after: 1 week
