dynamic rules. We are doing forwarding in the following cases:
o For the simple ipfw fwd rule, e.g.
fwd 10.0.0.1 ip from any to any out xmit em0
fwd 127.0.0.1,3128 tcp from any to any 80 in recv em1
o For the dynamic fwd rule, e.g.
fwd 192.168.0.1 tcp from any to 10.0.0.3 3333 setup keep-state
When this rule triggers it creates a dynamic rule, but this
dynamic rule should forward packets only in forward direction.
o And the last case that does not work before - simple fwd rule which
triggers when some dynamic rule is already executed.
PR: kern/147720, kern/150798
MFC after: 1 month
The binutils update in r218822 caused the MIPS n64 dynamic binaries to
fail because the ".interp" section is not in the initial sections.
This happens because elf64bmip-defs.sh overrides INITIAL_READONLY_SECTIONS
to add ".MIPS.options" sections instead of the ".reginfo" section used
by n32.
This used to work fine, but after r218822, INITIAL_READONLY_SECTIONS also
contains the .interp section, so the override has to be done differently.
Reported by : aduane at juniper
Obtained from: gonzo (Initial version)
In msgbuf_reinit() and msgbuf_init(), we weren't initializing the mutex.
Depending on the contents of memory, the LO_INITIALIZED flag might be
set on the mutex (either due to a warm reboot, and the message buffer
remaining in place, or due to garbage in memory) and in that case, with
INVARIANTS turned on, we would trigger an assertion that the mutex had
already been initialized.
Fix this by bzeroing the message buffer mutex for the _init() and _reinit()
paths.
Reported by: mdf
The version is used to check if a module is already preset, not setting
it results in:
can't re-use a leaf (ipw)!
module_register: module pci/ipw already exists!
Module pci/ipw failed to register: 17
while trying to load the module due to an entry in loader.conf. With this
commit we get the expected:
module ipw already present!
Reported by: Dru Lavigne, bz
Tested by: bz
MFC after: 1 week
process received frames. Previously it was possible to handle RX
interrupts even if controller is not fully initialized. This
resulted in non-working driver after system is up and running.
Reported by: hselasky
Tested by: hselasky
Pathconf RPC for cases where the reply doesn't include
the answer. This fixes a problem reported by avg@ where
the NFSv3 Pathconf RPC would fail when "ls -l" did an
lpathconf(2) for _PC_ACL_NFS4.
Tested by: avg
MFC after: 2 weeks
While we have had a fix in place (options PRINTF_BUFR_SIZE=128) to fix
scrambled console output, the message buffer and syslog were still getting
log messages one character at a time. While all of the characters still
made it into the log (courtesy of atomic operations), they were often
interleaved when there were multiple threads writing to the buffer at the
same time.
This fixes message buffer accesses to use buffering logic as well, so that
strings that are less than PRINTF_BUFR_SIZE will be put into the message
buffer atomically. So now dmesg output should look the same as console
output.
subr_msgbuf.c: Convert most message buffer calls to use a new spin
lock instead of atomic variables in some places.
Add a new routine, msgbuf_addstr(), that adds a
NUL-terminated string to a message buffer. This
takes a priority argument, which allows us to
eliminate some races (at least in the the string
at a time case) that are present in the
implementation of msglogchar(). (dangling and
lastpri are static variables, and are subject to
races when multiple callers are present.)
msgbuf_addstr() also allows the caller to request
that carriage returns be stripped out of the
string. This matches the behavior of msglogchar(),
but in testing so far it doesn't appear that any
newlines are being stripped out. So the carriage
return removal functionality may be a candidate
for removal later on if further analysis shows
that it isn't necessary.
subr_prf.c: Add a new msglogstr() routine that calls
msgbuf_logstr().
Rename putcons() to putbuf(). This now handles
buffered output to the message log as well as
the console. Also, remove the logic in putcons()
(now putbuf()) that added a carriage return before
a newline. The console path was the only path that
needed it, and cnputc() (called by cnputs())
already adds a carriage return. So this
duplication resulted in kernel-generated console
output lines ending in '\r''\r''\n'.
Refactor putchar() to handle the new buffering
scheme.
Add buffering to log().
Change log_console() to use msglogstr() instead of
msglogchar(). Don't add extra newlines by default
in log_console(). Hide that behavior behind a
tunable/sysctl (kern.log_console_add_linefeed) for
those who would like the old behavior. The old
behavior led to the insertion of extra newlines
for log output for programs that print out a
string, and then a trailing newline on a separate
write. (This is visible with dmesg -a.)
msgbuf.h: Add a prototype for msgbuf_addstr().
Add three new fields to struct msgbuf, msg_needsnl,
msg_lastpri and msg_lock. The first two are needed
for log message functionality previously handled
by msglogchar(). (Which is still active if
buffering isn't enabled.)
Include sys/lock.h and sys/mutex.h for the new
mutex.
Reviewed by: gibbs
rather than at the bottom of the manpage.
- Remove an obsolete comment about SWAIT being a stale state. It was
resurrected for a different purpose in FreeBSD 5 to mark idle ithreads.
- Add a comment documenting that the SLEEP and LOCK states typically
display the name of the event being waited on with lock names being
prefixed with an asterisk and sleep event names not having a prefix.
MFC after: 1 week
be brought up in the order they are enumerated in the device tree (in
particular, that thread 0 on each core be brought up first). The SLIST
through which we loop to start the CPUs has all of its entries added with
SLIST_INSERT_HEAD(), which means it is in reverse order of enumeration
and so AP startup would always fail in such situations (causing a machine
check or RTAS failure). Fix this by changing the SLIST into an STAILQ,
and inserting new CPUs at the end.
Reviewed by: jhb
idle threads). The process is displayed by default (subject to whether or
not system processes are displayed) to preserve existing behavior. The
system idle process can be hidden via the '-z' command line argument or the
'z' key while top is running. When it is hidden, top more closely matches
the behavior of FreeBSD <= 4.x where idle time was not accounted to any
process.
MFC after: 2 weeks
to not only compile bu load as well for testing with IPv6-only kernels.
For the moment we ignore the csum change in pf_ioctl.c given the
pending update to pf45.
Reported by: dru
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 20 days
Add some additional empty string checks for IPv4 and try to configure
a netmask along with the address rather than doing things twice.
Contrary to AUTO-DHCP, IPv6-SLAAC will accept static configuration
as well, which we will use at least for resolv.conf currently and
if we were given a static address configure that as an alias as well.
The pc-sysinstaller changes going along were committed to PC-BSD as r10773.
Reviewed by: kmoore
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 20 days
If compiled in for dual-stack use, test with feature_present(3)
to see if we should register the IPv4/IPv6 address family related
options.
In case there is no "inet" support we would love to go with the
usage() and make the address family mandatory (as it is for anything
but inet in theory). Unfortunately people are used to
ifconfig IF up/down
etc. as well, so use a fallback of "link". Adjust the man page
to reflect these minor details.
Improve error handling printing a warning in addition to the usage
telling that we do not know the given address family in two places.
Reviewed by: hrs, rwatson
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 2 weeks
reporting it properly (none? of known disks now).
Hitachi and WDC AF disks seem could be identified more or less formally.
For Seagate and Samsung enumerate some found models/series.
For other disks it can be forced with kern.cam.ada.X.quirks=1 tunable.
User upgrades his system to fix the problem, but if he has any ZFS snapshots
for the file system which contains problematic binary, any user can mount the
snapshot and execute vulnerable binary.
Prevent this from happening by always mounting snapshots with setuid turned off.
MFC after: 2 weeks
If not specified, network.subr will add it automatically if we have
INET support (1).
In network.subr only call the address family up/down functions
if the respective AF is available.
Switch to new kern.features variables for inet and inet6 as the
inet sysctl tree is also available for IPv6-only kernels leading
to unexpected results.
Suggested by: hrs (1)
Reviewed by: hrs
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 20 days
As noted in Austin Group issue #370 (an interpretation has been issued),
failing posix_spawn() because an fd specified with
posix_spawn_file_actions_addclose() is not open is unnecessarily harsh, and
there are existing implementations that do not fail posix_spawn() for this
reason.
Reviewed by: ed
MFC after: 10 days
queues. Try to have a set of these per port when possible, fall back
to sharing a common pool between all ports otherwise.
- One control queue per port (used to be one per hardware channel).
- t4_eth_rx now handles Ethernet rx only.
- sysctls to display pidx/cidx for some queues.
MFC after: 1 week
filters working. (All other filters - switch without L2 info rewrite,
steer, and drop - were already fully-functional).
Some contrived examples of "switch" filters with L2 rewriting:
# cxgbetool t4nex0 iport 0 dport 80 action switch vlan +9 eport 3
Intercept all packets received on physical port 0 with TCP port 80 as
destination, insert a vlan tag with VID 9, and send them out of port 3.
# cxgbetool t4nex0 sip 192.168.1.1/32 ivlan 5 action switch \
vlan =9 smac aa:bb:cc:dd:ee:ff eport 0
Intercept all packets (received on any port) with source IP address
192.168.1.1 and VLAN id 5, rewrite the VLAN id to 9, rewrite source mac
to aa:bb:cc:dd:ee:ff, and send it out of port 0.
MFC after: 1 week
hardware supports it.
Since ni->ni_htcap in hostap mode is what the remote end has advertised,
not what has been negotiated/decided, we need to check ourselves what
the current channel width is and what the hardware supports before
enabling short-GI.
It's important that short-GI isn't enabled when it isn't negotiated
and when the hardware doesn't support it (ie, short-gi for 20mhz channels
on any chip < AR9287.)
I've quickly verified this on the AR9285 in 11n mode.
- The existing ipi_lock continues to protect the global inpcb list and
inpcb counter. This lock is now relegated to a small number of
allocation and free operations, and occasional operations that walk
all connections (including, awkwardly, certain UDP multicast receive
operations -- something to revisit).
- A new ipi_hash_lock protects the two inpcbinfo hash tables for
looking up connections and bound sockets, manipulated using new
INP_HASH_*() macros. This lock, combined with inpcb locks, protects
the 4-tuple address space.
Unlike the current ipi_lock, ipi_hash_lock follows the individual inpcb
connection locks, so may be acquired while manipulating a connection on
which a lock is already held, avoiding the need to acquire the inpcbinfo
lock preemptively when a binding change might later be required. As a
result, however, lookup operations necessarily go through a reference
acquire while holding the lookup lock, later acquiring an inpcb lock --
if required.
A new function in_pcblookup() looks up connections, and accepts flags
indicating how to return the inpcb. Due to lock order changes, callers
no longer need acquire locks before performing a lookup: the lookup
routine will acquire the ipi_hash_lock as needed. In the future, it will
also be able to use alternative lookup and locking strategies
transparently to callers, such as pcbgroup lookup. New lookup flags are,
supplementing the existing INPLOOKUP_WILDCARD flag:
INPLOOKUP_RLOCKPCB - Acquire a read lock on the returned inpcb
INPLOOKUP_WLOCKPCB - Acquire a write lock on the returned inpcb
Callers must pass exactly one of these flags (for the time being).
Some notes:
- All protocols are updated to work within the new regime; especially,
TCP, UDPv4, and UDPv6. pcbinfo ipi_lock acquisitions are largely
eliminated, and global hash lock hold times are dramatically reduced
compared to previous locking.
- The TCP syncache still relies on the pcbinfo lock, something that we
may want to revisit.
- Support for reverting to the FreeBSD 7.x locking strategy in TCP input
is no longer available -- hash lookup locks are now held only very
briefly during inpcb lookup, rather than for potentially extended
periods. However, the pcbinfo ipi_lock will still be acquired if a
connection state might change such that a connection is added or
removed.
- Raw IP sockets continue to use the pcbinfo ipi_lock for protection,
due to maintaining their own hash tables.
- The interface in6_pcblookup_hash_locked() is maintained, which allows
callers to acquire hash locks and perform one or more lookups atomically
with 4-tuple allocation: this is required only for TCPv6, as there is no
in6_pcbconnect_setup(), which there should be.
- UDPv6 locking remains significantly more conservative than UDPv4
locking, which relates to source address selection. This needs
attention, as it likely significantly reduces parallelism in this code
for multithreaded socket use (such as in BIND).
- In the UDPv4 and UDPv6 multicast cases, we need to revisit locking
somewhat, as they relied on ipi_lock to stablise 4-tuple matches, which
is no longer sufficient. A second check once the inpcb lock is held
should do the trick, keeping the general case from requiring the inpcb
lock for every inpcb visited.
- This work reminds us that we need to revisit locking of the v4/v6 flags,
which may be accessed lock-free both before and after this change.
- Right now, a single lock name is used for the pcbhash lock -- this is
undesirable, and probably another argument is required to take care of
this (or a char array name field in the pcbinfo?).
This is not an MFC candidate for 8.x due to its impact on lookup and
locking semantics. It's possible some of these issues could be worked
around with compatibility wrappers, if necessary.
Reviewed by: bz
Sponsored by: Juniper Networks, Inc.
