associated patch to XFree86 allows the X server to work with this chipset
on FreeBSD. Additional work will include porting the Linux 3D driver.
Submitted by: Ruslan Ermilov <ru@FreeBSD.org>
the gating of system calls that cause modifications to the underlying
filesystem. The gating can be enabled by any filesystem that needs
to consistently suspend operations by adding the vop_stdgetwritemount
to their set of vnops. Once gating is enabled, the function
vfs_write_suspend stops all new write operations to a filesystem,
allows any filesystem modifying system calls already in progress
to complete, then sync's the filesystem to disk and returns. The
function vfs_write_resume allows the suspended write operations to
begin again. Gating is not added by default for all filesystems as
for SMP systems it adds two extra locks to such critical kernel
paths as the write system call. Thus, gating should only be added
as needed.
Details on the use and current status of snapshots in FFS can be
found in /sys/ufs/ffs/README.snapshot so for brevity and timelyness
is not included here. Unless and until you create a snapshot file,
these changes should have no effect on your system (famous last words).
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
Currently, many drivers support more than one bus of ISA, EISA, MCA,
PCI.
Before this commit, we had, for example, some SCSI devices listed more
than once, iirc, some up to three times (ISA/EISA, MCA, PCI).
Since now the "device" line is common for all of them and they only
differ for the hints stuff, I did the following:
First, list Busses: (E)ISA, MCA, PCI and explain, that only ISA
needs the hints stuff.
Move NIC/SCSI stuff, which were the only split sections, behind these
stuff. Describe all drivers only one time and list all supported
chips.
List all device (+ hints for ISA, if possible).
I've also added few additional supported chips to some drivers, xl for
example and some SCSI drivers.
Also, softupdates is no longer disabled by default, so the comment should
not say, it's not enabled by default due to license issues.
Approved by: asmodai
To come: include PAO devices (imp volunteered for help)
FreeBSD.org e-mail.
o Notice also that it's listed as "aud" not "audit" which will
probably change in the near future with updates to the auditing
implementation.
set equal to the number of kilobytes in your cache. The old options are
still supported for backwards compatibility.
Submitted by: Kelly Yancey <kbyanc@posi.net>
This means 'options NETGRAPH' is no longer necessary in order to get
netgraph-enabled Ethernet interfaces. This supports loading/unloading
the ng_ether.ko and attaching/detaching the Ethernet interface in any
order.
Add two new hooks 'upper' and 'lower' to allow access to the protocol
demux engine and the raw device, respectively. This enables bridging
to be defined as a netgraph node, if so desired.
Reviewed by: freebsd-net@freebsd.org
rest of the kernel. Added new option TDFX_LINUX for optional
LINUX_EMULATION, so that perhaps some people don't have to use linux emu to
run the driver if they don't want to.
accept filters are now loadable as well as able to be compiled into
the kernel.
two accept filters are provided, one that returns sockets when data
arrives the other when an http request is completed (doesn't work
with 0.9 requests)
Reviewed by: jmg
world as was our old way, rather than when building a kernel.
Some people do not like the new way, and the release building still assumes
modules are built with the world.
implying that they aren't used for the rest of the system.
Fix the lies:
253 is used by mfs (bad MFS for not registering it).
254 is a magic cookie inside of the dev code in at least one place.
255 is -1 which is magic in a different way in the dev code.
So, that means that 200-252 are reserved for local users. A grep for
252 didn't turn anything up, so I'm assuming it and lower are safe.
And I thought I was being smart by allocating our local major numbers
from 254 on down. This caused very very odd problems that were hard
to track down: close not being called, sync failing at reboot, etc.
Implement the Solaris way to break into DDB over a serial console
instead of sending a break. Sending the character sequence
CR ~ ^b will break the kernel into DDB (if DDB is enabled).
Reviewed by: peter
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.
config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel. You can reconfigure your
isa devices with the likes of this at loader(8) time:
set hint.ed.0.port=0x320
userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.
It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8). See the "hints" directive in GENERIC
as an example.
All device wiring has been moved out of config(8). There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file. If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you. You can also compile in the
hints directly with: hints "device.hints" as well.
There are a few things that I'm not too happy with yet. Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it. However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built. A stack of man4 pages will need updating. :-/
Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated. eg: 'device fe 4' will compile the fe driver with NFE set
to 4. You can then set hints for 4 units (0 - 3). Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this. This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.
Please exercise EXTREME CAUTION when transitioning!
Moral support by: phk, msmith, dfr, asmodai, imp, and others
Socket 8 to 370 converters. When (1) CPU_PPRO2CELERON option is
defined, (2) Intel CPU is found and (3) CPU ID is 0x66?, L2 cache is
enabled through MSR 0x11e. The L2 cache latency value can be
specified by CPU_L2_LATENCY option. Default value of L2 cache latency
is 5.
These options are useful if you use Socket 8 to Socket 370 converter
(e.g. Power Leap's PL-Pro/II.) Most PentiumPro BIOSs don't enable L2
cache of Mendocino Celeron CPUs because they don't know Celeron CPUs.
These options are needles if you use a Coppermine (FCPGA) Celeron or
PentiumIII, becuase the L2 cache enable bit is hard wired and L2 cache
is always enabled.
2. Newbusify the driver.
3. Build as a module.
4. Use correct minor numbers when creating device files.
5. Correctly lock control characters.
6. Return ENXIO when device not configured.
Submitted by: Tor Egge <Tor.Egge@fast.no>
7. Fix the baud_table.
Submitted by: Elliot Dierksen <ebd@oau.org>
Note:
- the old driver still lives in src/sys/i386/isa, so that you can
revert to it if something goes wrong.
- The module does not detach very well. Attaching works fine.
