platforms.
This allows to not depend on the IOMMU macro in AHCI driver.
Requested by: kib
Suggested by: andrew
Reviewed by: kib
Sponsored by: Innovate DSbD
Differential Revision: https://reviews.freebsd.org/D26887
Some controllers use PCI function 1 as the requester ID for DMA transfers,
but the controllers are not PCI multifunction.
Set the iommu buswide flag for them. This should instruct an IOMMU driver
to use the same translation rule for all the devices and functions of
a bus.
This was discovered on the ARM Neoverse N1 System Development Platform
(ARM N1SDP).
Bug reference: https://bugzilla.kernel.org/show_bug.cgi?id=42679
Reported by: andrew
Reviewed by: kib, mav
Sponsored by: Innovate DSbD
Differential Revision: https://reviews.freebsd.org/D26857
My AMD Ryzen system has 4 AHCI controllers, each supporting 16 MSI vectors.
Since two of the controllers have only one SATA port, limit to single MSI
saves system 30 interrupt vectors for free.
It may be possible to also limit number of MSI vectors to 4 and 8 for the
other two controllers, but according to the AHCI specification after that
controllers may revert to only one vector, that would be a bigger loss to
risk.
MFC after: 2 weeks
Implement support for AHCI controller found in
NXP QorIQ Layerscape SoCs.
Submitted by: Artur Rojek <ar@semihalf.com>
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Alstom Group
Differential Revision: https://reviews.freebsd.org/D24466
This allows clean handoff from BIOS implementing some asynchronous I/O to
the OS AHCI driver. During attach driver declares OS ownership request
and waits from 25ms to 2s for BIOS to complete operation and release the
hardware.
MFC after: 2 weeks
JMB582 has 2 6Gbps SATA ports and PCIe 3.0 x1.
JMB585 has 5 6Gbps SATA ports and PCIe 3.0 x2.
Both chips support AHCI v1.31, Port Multiplier with FBS and 8 MSI vectors.
MFC after: 2 weeks
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
Intel has created RST and many laptops from vendors like Lenovo and Asus. It's a
mechanism for creating multiple boot devices under windows. It effectively hides
the nvme drive inside of the ahci controller. The details are supposed to be a
trade secret. However, there's a reverse engineered Linux driver, and this
implements similar operations to allow nvme drives to attach. The ahci driver
attaches nvme children that proxy the remapped resources to the child. nvme_ahci
is just like nvme_pci, except it doesn't do the PCI specific things. That's
moved into ahci where appropriate.
When the nvme drive is remapped, MSI-x interrupts aren't forwarded (the linux
driver doesn't know how to use this either). INTx interrupts are used
instead. This is suboptimal, but usually sufficient for the laptops these parts
are in.
This is based loosely on https://www.spinics.net/lists/linux-ide/msg53364.html
submitted, but not accepted by, Linux. It was written by Dan Williams. These
changes were written from scratch by Olivier Houchard.
Submitted by: cognet@ (Olivier Houchard)
Since SES specs do not define mechanism to map enclosure slots to SATA
disks, AHCI EM code I written many years ago appeared quite useless,
that always bugged me. I was thinking whether it was a good idea, but
if LSI HBAs do that, why I shouldn't?
This change introduces simple non-standard mechanism for the mapping
into both AHCI EM and SES code, that makes AHCI EM on capable controllers
(most of Intel's) a first-class SES citizen, allowing it to report disk
physical path to GEOM, show devices inserted into each enclosure slot in
`sesutil map` and `getencstat`, control locate and fault LEDs for specific
devices with `sesutil locate adaX on` and `sesutil fault adaX on`, etc.
I've successfully tested this on Supermicro X10DRH-i motherboard connected
with sideband cable of its S-SATA Mini-SAS connector to SAS815TQ backplane.
It can indicate with LEDs Locate, Fault and Rebuild/Remap SES statuses for
each disk identical to real SES of Supermicro SAS2 backplanes.
MFC after: 2 weeks
We do this for FDT systems but not for ACPI ones.
Check the presence of the _CCA attribute.
Sponsored by: Ampere Computing, LLC
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D20144
Use BUS_DMA_NOWAIT for loads at initialization time.
Report actual numeric error code if any problem occurs at the
initialization.
Reported and tested by: pho
Reviewed by: mav
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D18741
initialize the controller.
According to the datasheet, the old code checks if port 2 (P2E, 0x4) was
the only enabled port (except port 0, which was ignored by mask 0xfe),
and issue a write to the PCS register to disable all but port 0, right
before ahci_ctlr_reset.
Some other operating systems would issue a port enable to all ports, but
since the current code only does the special initialization for ICH8M,
it entirely and rely on BIOS to do the right thing (the alternative
would be https://reviews.freebsd.org/D18300?id=50922 , should we see
reports that we really need to do it).
Reviewed by: mav
MFC after: 3 months
Differential Revision: https://reviews.freebsd.org/D18300
As part of Chuck's work on fixing kernel crashes caused by disk I/O
errors, it is useful to be able to trigger various kinds of
errors. This patch allows causing an AHCI-attached disk to disappear,
by having the driver keep the PHY disabled when the driver would
otherwise enable the PHY. It also allows making the disk reappear by
having the driver go back to setting the PHY enable/disable state as
it normal would and simulating the hardware event that causes a bus
rescan.
Submitted by: Chuck Silvers
Sponsored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D16043
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
There were some bits that were being set in cmd_flags (a field of AHCI's
command list structure) after cmd_flags was converted to little endian.
On a big endian host, such as PowerPC, this would set the wrong bits.
This was preventing AHCI driver from working on these hosts.
Reviewed by: jhibbits
Approved by: jhibbits (mentor)
Mark the PNP table, but still need to handle the CLASS / SUBCLASS /
REVID matching.
Reviewed by: imp, chuck
Submitted by: Lakhan Shiva Kamireddy <lakhanshiva@gmail.com>
Sponsored by: Google, Inc. (GSoC 2018)
Two modules with the same name cannot be loaded, so Marvell specific drivers
cannot have the same name as the generic drivers.
Files with the same name, even in different folders overlaps their .o files,
so in order to prepare for supporting Marvell platforms in GENERIC armv7
config, modify conflicting names.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14743
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
attachment code for various SOCs and busses. Remove all the static and
should-have-been-static and named-differently instances of it.
This should eliminate the recently-grown build warnings about multiple
definitions when building arm kernels.
busdma know, so that on architectures where dma isn't always coherent, we
know we don't have to write-back/invalidates cachelines on DMA operations.
Reviewed by: andrew, mav
Taking closer look on my ASM1062 I found that it has bunch of issues around
error recovery: reported wrong CCS, failed commands reported as completed,
READ LOG EXT times out after NCQ error. This patch workarounds first two
problems, that were making ATAPI devices close to unusable on these HBAs.
MFC after: 2 weeks
This file provides support for AHCI mode on Armada38x
and adds new optional AHCI device to arm/mv/files.mv.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9222
It occurred that some Marvell integrated controllers
require additional time after soft reset to work properly.
Introduce new quirk (AHCI_Q_MRVL_SR_DEL), that enable
such operation.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: mav
Differential revision: https://reviews.freebsd.org/D9221
in some arm64 hardware, for example the AMD Opteron A1100.
Reviewed by: mav
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8852
