Xeon 5500/5600 series:
- Utilize IA32_TEMPERATURE_TARGET, a.k.a. Tj(target) in place
of Tj(max) when a sane value is available, as documented
in Intel whitepaper "CPU Monitoring With DTS/PECI"; (By sane
value we mean 70C - 100C for now);
- Print the probe results when booting verbose;
- Replace cpu_mask with cpu_stepping;
- Use CPUID_* macros instead of rolling our own.
Approved by: rpaulo
MFC after: 1 month
from the inline assembly. This allows the compiler to cache invocations of
curthread since it's value does not change within a thread context.
Submitted by: zec (i386)
MFC after: 1 week
a PMC. It was possible that we could have turned a bit on but
never cleared it.
Extend the calls to rdmsr() to all necessary functions, not
just those which previously caused a panic.
Pointed out by: jhb@
MFC after: 1 week
Fix another fallout from r208833. savectx() is used to save CPU context
for crash dump (dumppcb) and kdb (stoppcbs). For both cases, we cannot
have a valid pointer in pcb_save. This should restore the previous
behaviour.
for crash dump (dumppcb) and kdb (stoppcbs). For both cases, there cannot
have a valid pointer in pcb_save. This should restore the previous
behaviour.
So a command like
kill _HUP 1
now fails without sending SIGTERM to init.
The behaviour when kill(2) fails remains unchanged: processing continues.
This matches other implementations and POSIX and is useful for killing
multiple processes at once when some of them may already be gone.
PR: bin/40282
run. This makes the 'ctfconvert' and 'ctfmerge' programs show up during
a build when compiling a kernel, a library or a program.
Sponsored by: The FreeBSD Foundation
PR SCTP FWD-TSN's would not be sent and thus
cause a stalled connection. Also the rwnd
Calculation was also off on the receiver side for
PR-SCTP.
MFC after: 1 month
The emulation of 'ld' and 'sd' instructions only works for ABIs that support
64-bit registers and the instructions 'ldl' and 'ldr' that operate on those
registers.
Reviewed by: jmallett
that with a 32-bit ABI on a system with 64-bit registers can attempt to
access an invalid (well, kernel) memory address rather than the intended
user address for stack-relative loads and stores. Lowering the stack
pointer works around this. [1]
o) Make TRAP_DEBUG code conditional on the trap_debug variable. Make
trap_debug default to 0 instead of 1 now but make it possible to change it
at runtime using sysctl.
o) Kill programs that attempt an unaligned access of a kernel address. Note
that with some ABIs, calling useracc() is not sufficient since the register
may be 64-bit but vm_offset_t is 32-bit so a kernel address could be
truncated to what looks like a valid user address, allowing the user to
crash the kernel.
o) Clean up unaligned access emulation to support unaligned 16-bit and 64-bit
accesses. (For 16-bit accesses it was checking for user access to too much
memory (4 bytes) and there was no 64-bit support.) This still lacks support
for unaligned load-linked and store-conditional.
Reviewed by: [1] gonzo
and exclusion patterns [1]
- Some improvements on the exiting code, like replacing memcpy with
strlcpy/strcpy
Approved by: delphij (mentor)
Pointed out by: bf [1], des [1]
the official vendor listed for 0x076b, rather than Omnikey, as in the PR.
PR: usb/123351
Submitted by: Marcin Cieslak <saper SYSTEM.PL>
MFC after: 1 week
avoid a hang in the SSL case if the server sends a close notification
before we are done reading. In the non-SSL case, it can provide a
minor (but probably not noticeable) performance improvement for small
transfers.
MFC after: 3 weeks
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
