and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
Add a sysctl 'machdep.cs_recv_delay' to specify how long to wait after
receiving a packet in order to check for a subsequent (back-to-back)
packet. The cs8900 has a very small receive buffer, so this helps avoid
overflows at the cost of some extra CPU overhead.
Submitted by: Oleg Sharoiko <os@rsu.ru>, MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
The check for dropping unicast packets not sent to our ethernet
address is after the bpf tap, but not conditioned on it. All packets
received should get handed to bpf, and unicast packets not to us (mac)
should get dropped whether or not there is a bpf listener. I believe
that the common optimization that the interface is in hw promisc mode
iff there is a bpf listener is in general wrong, but more frequently
so on wavelans.
I think Max's fix makes bpf listeners not see unicast packets sent to
others, but I'm not sure.
One can argue that checking on MOD_ENAL is wrong, but the code only
drops packets that shouldn't be received. The correctness condition
is that it be run whenever unicast packets without our mac address can
be received.
PR: kern/7144
Submitted by: Greg Troxel <gdt@ir.bbn.com>
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
I don't have access to a real VT220 to verify this against.
However, I'm committing the patch in `good faith' because
(a) getting hold of a real VT220 is going to be increasingly difficult
the longer the PR sits around,
(b) some one was troubled enough to in a PR and
(c) the fix is minor and has no other implications.
PR: 7559
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
of invariants to cyattach().
Fixed minor bugs:
- cyparam() returned without restoring the ipl in the error cases. This
was harmless because cyparam() is always called at spltty().
- one check for "rev. J or higher" actually checked for precisely rev. J.
swapped RTS/DTR). Merge the vendor's modification of the 2.2.6-release
version into -current for reference. Will be cleaned up in next commit.
Obtained from: ftp://ftp.cyclades.com/pub/cyclades/cyclom-y/freebsd/2.2.6/cyy226.tar.gz
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
in ddb) which I broke by changing %8[l]x to %8p. Hacked the central
printf routine to not add an "0x" prefix for %p formats if the field
width is nonzero. The tables are still horribly misformatted on
64-bit machines.
Use %p instead of %8p to print pointers when the field width isn't
important.
chip.
It has been observed that the problem is most apparent:
a) in notebook computers,
b) and/or in the systems with C&T video chips.
Define the new configuration option SC_BAD_FLICKER in the kernel
configuration file to remove outb()/outw() calls in question.
DOS partition type 15 (Extended DOS, LBA) as a container for
DOS logical volumes, so the appropriate slices (e.g. sd1s5)
are not initialized.
PR: 7549
PR: 4120
Reviewed by: phk
Submitted by: Jim Mattson <jmattson@sonic.net>
- ppbus now supports PLIP via the if_plip driver
- ieee1284 infrastructure added, including parallel-port PnP
- port microsequencer added, for scripting the sort of port I/O
that is common with parallel devices without endless calls up and down
through the driver structure.
- improved bus ownership behaviour among the ppbus-using drivers.
- improved I/O chipset feature detection
The vpo driver is now implemented using the microsequencer, leading to
some performance improvements as well as providing an extensive example
of its use.
Reviewed by: msmith
Submitted by: Nicolas Souchu <Nicolas.Souchu@prism.uvsq.fr>
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
the screen mode is changed even if another vty has larger size.
Reallocate the buffer only when the new screen size is larger than
the current cut buffer size.
