apm_setup.s was storing apm_cs16_base and apm_cs32_base addresses in
each others slots, and apm.c was reversing the result so the bugs
cancelled out, but the code looked wrong.
No functional differences unfortunately.
Submitted by: dave edmondson <davided@sco.com>
type identification code out of machdep.c and into a new file of its
own. Hopefully other grot can be moved out of machdep.c as well
(by other people) into more descriptively-named files.
Add code to the boot blocks to allow the user to place default boot strings
on block 1 of the disk (2nd block), should the correct magic numbers be present.
If the correct options are used it will 'delete' the name used from block1,
thereby assuring that if the boot fails it won't be stuck in an infinite loop.
the boot strings are set by the utility "nextboot"
(not yet checked in, but being tested.)
By default these changes should have no effect on existing installations
and if compiled without the NAMEBLOCK option should be essentially identical
to the old ones.
based on the HD64570 chip. Both the 1 and 2 port cards is supported.
Line speeds of up to 2Mbps is possible. At this speed about 95% of the
bandwidth is usable with 486DX processors.
The standard FreeBSD sppp code is used for the link level layer. The
default protocol used is PPP. The Cisco HDLC protocol can be used by
adding "link2" to the ifconfig line in /etc/sysconfig or where ever
ifconfig is run.
At the moment only the X.21 interface is tested. The others may need
tweaks to the clock selection code.
Testing with the high frequency of 20000 Hz (to find problems) only found
the problem that this frequency is too high for slow i386's.
Disable interrupts while setting the timer frequency. This was unnecessary
before rev.1.57 and forgotten in rev.1.57. The critical (i8254) interrupts
are disabled in another way at boot time but not in the sysctl to change
the frequency.
Fixed profiling of system times. It was pre-4.4Lite and didn't support
statclocks. System times were too small by a factor of 8.
Handle deferred profiling ticks the 4.4Lite way: use addupc_task() instead
of addupc(). Call addupc_task() directly instead of using the ADDUPC()
macro.
Removed vestigial support for PROFTIMER.
switch.s:
Removed addupc().
resourcevar.h:
Removed ADDUPC() and declarations of addupc().
cpu.h:
Updated a comment. i386's never were tahoe's, and the deferred profiling
tick became (possibly) multiple ticks in 4.4Lite.
Obtained from: mostly from NetBSD
multiplication in addupc() overflowed for addresses >= 256K, assuming
the usual profil(2) scale parameter of 0x8000. addupc() will go away
soon.
Submitted by: John Polstra <jdp@polstra.com>
via an ioctl (MOUSE_ACTION).
Fixed a couple of bugs (destructive cursor, uncut, jitter).
Now applications can use the mouse via the MOUSE_MODE ioctl, its
possible to have a signal sent on mouseevents, makeing an event loop
in the application take over mouseevents.
things tend to work better if you write the settings to the correct
register.. (*blush*). This subtle bug has been haunting me for ages, and
will solve a few problems that have been reported to me.
Also, take a shot at fixing the serial BREAK processing, what was there
before never really worked. (There is a PR on this I think)
Real support for a Textmode mousecursor, works by reprogramming the
charset. Together with this support for cut&paste in text mode.
To use it a userland daemon is needed (moused), which provides
the interface to the various mice protokols.
Bug fixes here and there, all known PR's closed by this update.
is only used by the icu support modules and by a few drivers that know
too much about the icu (most only use it to convert `n' to `IRQn'). isa.h
is only used by ioconf.c and by a few drivers that know too much about
isa addresses (a few have to, because config is deficient).
to match (pc98/random_machdep.c probably requires a similar change). This
is a problem area for the PC98 merge - all PC98 ifdefs in <machine/*.h> are
kludges to work around incorrect layering.
Original version by John Hay.
Simplified timestamp code by reading the time exactly when necessary.
This may slow down the interrupt handler with extra calls to microtime(),
but only in bad configurations - the input fifo should normally be
disabled if timestamps on input are being used, since otherwise the
timestamp won't be precisely associated with any particular input event.
The interrupt handler remains slowed down by one test and branch for
each input (and now DCD change) event - avoiding this is not practical
yet.
The simplifications also fixed:
- timestamps for input sometimes being clobbered by output and modem
status interrupts.
- valid timestamps not being available unless the port is configured with
vector siointrts. siointrts no longer exists.
- compiler warnings about siointr* in some configurations.
Simplified timestamp and probe code by depending on recent changes in
microtime() and DELAY() to preserve the interrupt enable flag.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
instead of sti to it restore to its usual state. pushfl/popfl is
actually faster in protected mode on Pentiums (4+3 cycles instead of 9),
and using sti made it extremely inconvenient to call microtime() from
fast interrupt handlers. pushfl/popfl is a couple of cycles slower than
sti on 486's and a couple more cycles slower on 386's, but the relative
cost of using it is not large since microtime() has to use slow i/o
instructions on the old cpus.
1) Make it much less likely to miss a wakeup in vm_page_free_wakeup
2) Create a new entry point into pmap: pmap_ts_referenced, eliminates
the need to scan the pv lists twice in many cases. Perhaps there
is alot more to do here to work on minimizing pv list manipulation
3) Minor improvements to vm_pageout including the use of pmap_ts_ref.
4) Major changes and code improvement to pmap. This code has had
several serious bugs in page table page manipulation. In order
to simplify the problem, and hopefully solve it for once and all,
page table pages are no longer "managed" with the pv list stuff.
Page table pages are only (mapped and held/wired) or
(free and unused) now. Page table pages are never inactive,
active or cached. These changes have probably fixed the
hold count problems, but if they haven't, then the code is
simpler anyway for future bugfixing.
5) The pmap code has been sorely in need of re-organization, and I
have taken a first (of probably many) steps. Please tell me
if you have any ideas.
parameters to printf() using the "D" format. (Why this even worked on
my box during testing I don't know, but as soon as I powered it on/off
it quite working.)
