vbus-supply properties may be specified for each PHY. These properties
reference a regulator that we must turn on/off as we turn the PHY on/off.
However, if the usbphy comes up before the regulator in question (as is the
case with GPIO-controlled regulators), then we will fail to grab a handle to
the regulator and control it as the PHY power state changes.
Fix it by just attaching the usbphy driver later. We don't really need it at
RESOURCE, we just need it to be before DEFAULT when ehci/ohci attach. In
particular, this fixes the USB NIC on a board that we don't yet supported-
without this, it will not power on and if_ure cannot attach.
Tested on: various boards [manu]
Tested on: OrangePi R1 [Rap2 (irc)]
Reported by: Rap2 (irc, "Cannot find USB NIC")
correctly for the data contained on each memory page.
There are several components to this change:
* Add a variable to indicate the start of the R/W portion of the
initial memory.
* Stop detecting NX bit support for each AP. Instead, use the value
from the BSP and, if supported, activate the feature on the other
APs just before loading the correct page table. (Functionally, we
already assume that the BSP and all APs had the same support or
lack of support for the NX bit.)
* Set the RW and NX bits correctly for the kernel text, data, and
BSS (subject to some caveats below).
* Ensure DDB can write to memory when necessary (such as to set a
breakpoint).
* Ensure GDB can write to memory when necessary (such as to set a
breakpoint). For this purpose, add new MD functions gdb_begin_write()
and gdb_end_write() which the GDB support code can call before and
after writing to memory.
This change is not comprehensive:
* It doesn't do anything to protect modules.
* It doesn't do anything for kernel memory allocated after the kernel
starts running.
* In order to avoid excessive memory inefficiency, it may let multiple
types of data share a 2M page, and assigns the most permissions
needed for data on that page.
Reviewed by: jhb, kib
Discussed with: emaste
MFC after: 2 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D14282
Pretty much any other device might need to manipulate a gpio pin during its
probe or attach routines, so these devices must be available as early as
possible.
The gpio device is an interrupt controller, but I didn't choose the
INTERRUPT pass for that reason (it works fine as an interrupt controller as
long as it attaches any time before interrupts are enabled). That just
looked like the right place in the passes to ensure that it attaches before
any type of device that might need gpio pin manipulations.
driver requires interrupts to do transfers, and the drivers for the SPI
devices on the bus quite reasonably expect to be able to do IO while probing
and attaching.
It would have been on an actual named pass before, but none were really
appropriate in name. Move it to the recently created SUPPORTDEV pass, which
perfectly describes it and keeps it in the right order.
Getting regulator is good, enabling them is better.
When the mmc stack decide to change the voltage for IO, don't
change the main vcc of the sd/mmc, only the io vcc.
AXP803 and AXP813/818 are very similar, only two regulators differs.
AXP803 is the companion chip for A64/R18
AXP813 is the companion chip for A83T
AXP818 is the companion chip for H8 (~A83T)
Add support for all regulators found in both of them.
to what other arches (all except riscv and armv4/5) do.
Submitted by: Hyun Hwang <hyun@caffeinated.codes>
Differential Revision: https://reviews.freebsd.org/D14465
(using "boot -d" at the loader propmt or setting boot_ddb in loader.conf).
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D14428
We don't support float in the boot loaders, so don't include
interfaces for float or double in systems headers. In addition, take
the unusual step of spiking double and float to prevent any more
accidental seepage.
Make vm_wait() take the vm_object argument which specifies the domain
set to wait for the min condition pass. If there is no object
associated with the wait, use curthread' policy domainset. The
mechanics of the wait in vm_wait() and vm_wait_domain() is supplied by
the new helper vm_wait_doms(), which directly takes the bitmask of the
domains to wait for passing min condition.
Eliminate pagedaemon_wait(). vm_domain_clear() handles the same
operations.
Eliminate VM_WAIT and VM_WAITPFAULT macros, the direct functions calls
are enough.
Eliminate several control state variables from vm_domain, unneeded
after the vm_wait() conversion.
Scetched and reviewed by: jeff
Tested by: pho
Sponsored by: The FreeBSD Foundation, Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D14384
This adds sys/modules/imx with a SUBDIR makefile to make the whole
collection of modules that are specific to these SoCs. Initially, that
"whole collection" consists of the if_ffec and imx_i2c drivers.
The if_ffec driver is referenced in its existing home in ../ffec rather
than moving it into the imx directory, because it's used by powerpc too,
but it is no longer built for all armv6/7 systems.
The imx_i2c driver is newly added as a module.
appears that node names no longer include leading zeroes in the @address
qualifiers, so we have to search for the nodes involved in interrupt fixup
using both flavors of name to be compatible with old and new .dtb files.
(You know you're in a bad place when you're applying a workaround to code
that exists only as a workaround for another problem.)
The FDT variant is called "gicv2m" too, and as both would try to register
on gic, only one of them would succeed, while we want them both in a
GENERIC kernel.
Reviewed by: andrew
significant source of cache line contention from vm_page_alloc(). Use
accessors and vm_page_unwire_noq() so that the mechanism can be easily
changed in the future.
Reviewed by: markj
Discussed with: kib, glebius
Tested by: pho (earlier version)
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14273
Remove most of the Atmel at91 boards. Most of them are no longer
relevant or used by people. Kept ATMEL since it should work on all the
boards that still work (I've not confirmed this, since I don't have
all these boards). Also kept SAM9G20EK, since I have several boards
that it is used on. If I've deleted a kernel in error, please let me
know.
On the OrangePi One at least, emac reset when an ethernet cable is not
plugged in seems to break ethernet. Soft reset will fail, even with
increasing the delay and retries to wait for up to 20 seconds. This can be
reproduced across at least two different OrangePi One's by simply leaving
ethernet cable unplugged when awg attaches. Whether it's plugged in or not
through u-boot process makes no difference.
Skipping the reset in this configuration doesn't seem to cause any problems,
tried across many many reboots with and without ethernet cable plugged in.
Tested on: OrangePi One
Tested on: Other boards (manu)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13974
global to per-domain state. Protect reservations with the free lock
from the domain that they belong to. Refactor to make vm domains more
of a first class object.
Reviewed by: markj, kib, gallatin
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14000
Similarly as we already do for arm64, for mitigation is necessary to
flush branch predictor when we:
- do task switch
- receive prefetch abort on non-userspace address
The user can disable this mitigation by setting 'machdep.disable_bp_hardening'
sysctl variable, or it can check actual system status by reading
'machdep.spectre_v2_safe'
The situation is complicated by fact that:
- for Cortex-A8, the BPIALL instruction is effectively NOP until the IBE bit
in ACTLR is set.
- for Cortex-A15, the BPIALL is always NOP. The branch predictor can be
only flushed by doing ICIALLU with special bit (Enable invalidates of BTB)
set in ACTLR.
Since access to the ACTLR register is locked to secure monitor/firmware on
most boards, they will also need update of firmware / U-boot.
In worst case, when secure monitor is on-chip ROM (e.g. PandaBoard),
the board is unfixable.
MFC after: 2 weeks
Reviewed by: imp, emaste
Differential Revision: https://reviews.freebsd.org/D13931
the "power down" watchdog used by the ROM boot code is still active when the
regular watchdog is activated, turn off the power-down watchdog.
This adds support for the "fsl,ext-reset-output" FDT property. When
present, that property indicates that a chip reset is accomplished by
asserting the WDOG1_B external signal, which is supposed to trigger some
external component such as a PMIC to ready the hardware for reset (for
example, adjusting voltages from idle to full-power levels), and assert the
POR signal to SoC when ready. To guard against misconfiguation leading to a
non-rebootable system, the external reset signal is backstopped by code
that asserts a normal internal chip reset if nothing responds to the
external reset signal within one second.
bottom of the file, where it is in most imx5/6 drivers. Switch from an RD2
macro using bus_space_read_2() to an inline function using bus_read_2();
likewise for WR2. Use RESOURCE_SPEC_END to end the resource_spec list.
Net effect should be no functional changes.
instead of frobbing the registers directly.
As a hack the bcm2835_pwm kmod presently ignores the 'status="disabled"'
in the RPI3 DTB, assuming that if you load the kld you probably
want the PWM to work.
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
