* Always use polled mode. The intr approach did not work for many
controllers and required the hw.acpi.ec.event_driven workaround.
* Only use an edge (not level) triggered GPE handler
* Add sc->ec_mtx for locking operations to a single EC. There were
many race conditions earlier between an SCI event and EcRead/Write.
* Use 1 ms as the global lock timeout
* Only acquire global lock if _GLK != 0
* Update EcWaitEvent to use an incremental backoff delay in its
poll loop. Wait 50 ms max instead of 10. Most ECs respond
in < 5 us (50 us when heavily loaded). However, some time out
occasionally even with a 10 ms timeout. For delays past 1 ms, use
msleep instead of DELAY to give SCI interrupts a chance to occur.
* Add EcCommand to send a command and wait for the appropriate event.
* The hw.acpi.ec.event_driven tunable is no longer applicable and
has been removed.
Ideas from: Linux
bus_dma_tag_create. We need to be sure that our packets are
kept in-sequence (that's how ATM is supposed to work) and
therefor use BUS_DMA_NOWAIT in all calls to bus_dmamap_load.
For memory allocated with bus_dmamem_alloc the use of anything
other than NULL arguments for the locking is anyway bogus because
this memory never should need bouncing and hence the load should never
be defered.
Allow the receipt of OAM and RM cells on raw connections. Caveat: it seems
that RM cells are still processed by the hardware even when we open the
connection as UBR.
register, present only on 3c90xB and later NICs. This meant that you could
not use a 1500 byte MTU with VLANs on original 3c905/3c900 cards (boomerang
chipset). The boomerang chip does support large frames though, just not
in the same way: you can set the 'allow large frames' bit in the MAC
control register to receive frames up to 4K in size.
Changes:
- Set the 'allow large frames' bit for boomerang chips and increase
the packet size register for cyclone and later chips. This allows
us to use IFCAP_VLAN_MTU on all supported xl(4) NICs.
- Actually set the IFCAP_VLAN_MTU flag in the capabilities word
in xl_attach().
- Change the method used to detect older boomerang chips. My 3c575C
cardbus NIC was being incorrectly identified as 3c90x chip instead
of 3c90xB because the capabilities word in its EEPROM reports
a bizzare value. In addition to checking for the supportsNoTxLength
bit, also check for the absence of the supportsLargePackets bit.
Both of these cases denote a 3c90xB chip.
- Make RX and TX checksums configurable via the SIOCSIFCAP ioctl.
- Avoid an unecessary le32toh() in xl_rxeof(): we already have the
received frame size in the lower 16 bits of rxstat, no need to
read it again.
Tested with 3c905-TX, 3c900-TPO, 3c980C and 3c575C NICs.
on the implied sign extension. The single unified VADDR() macro was
not able to avoid sign extending the VM_MAXUSER_ADDRESS/USRSTACK values.
Be explicit about UVADDR() (positive address space) and KVADDR()
(kernel negative address space) to make mistakes show up more
spectacularly.
Increase user VM space from 1/2TB (512GB) to 128TB.
corresponding release code. This was preventing the use of more than
1/2TB of user VM. I also spent a week staring at this code only to
eventually find that I'd mistakenly typed a P as an R.
rather than a non-existing pte. There is code elsewhere in i386/amd64
pmap that neglects to handle the large page cases because it knows that
it will see PG_PS in the returned "pte".
- Use atomic ops to update the bigpipe count
- Make the bigpipe count sysctl readable
- Remove a duplicate comparison in an if statement
- Comment two SYSCTLs.
extra trailing space.
- Don't bother probing a generic ISA bus device if isab0 already exists.
Some BIOSes place an ACPI psuedo-device with the HID of a generic ISA bus
device under the PCI-ISA bridge device. This is not the best solution
but will work for now. The isa bus driver only allows for one ISA bus
anyways.
having the PCI-ISA bridge driver depend on both pci and isa.
- Have the PCI-EISA bridge driver depend on both pci and eisa as well.
- Make acpi_isab.c depend on acpi and isa.
Submitted by: Marius Strobl <marius@alchemy.franken.de> (1,2)
extracted from received frames, both in the IFCAP_VLAN_HWTAGGING case
and not. (Some drivers may already do this masking internally, but
doing it here doesn't hurt and insures consistency.)
- In vlan_ioctl(), don't let the user set a VLAN ID value with anything
besides the VLID bits set, otherwise we will have trouble matching
an interface in vlan_input() later.
PR: kern/46405
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
than the shortcircuited version I had been using, which only worked
properly on i386 & amd64.
Also, change an autoscale constant to account for the more correct
kmem_map size.
Problem noticed by: mux
- Factor out code common to all ISA bridge drivers attach methods into a
isab_attach() function.
- Rename the PCI-ISA bridge driver's attach function to pci_isab_attach()
and have it call isab_attach().
support matching a list of addr/mask pairs so one can write
more efficient rulesets which were not possible before e.g.
add 100 skipto 1000 not src-ip 10.0.0.0/8,127.0.0.1/8,192.168.0.0/16
The change is fully backward compatible.
ipfw2 and manpage commit to follow.
MFC after: 3 days
- Limit the total number of pipes so that we do not
exhaust all vm objects in the kernel map. When
this limit is reached, a ratelimited message will
be printed to the console.
- Put a soft limit on the amount of memory consumable
by pipes. Once the limit has been reached, all new
pipes will be limited to 4K in size, rather than the
default of 16K.
- Put a limit on the number of pages that may be used
for high speed page flipping in order to reduce the
amount of wired memory. Pipe writes that occur
while this limit is exceeded will fall back to
non-page flipping mode.
The above values are auto-tuned in subr_param.c and
are scaled to take into account both the size of
physical memory and the size of the kernel map.
These limits help to reduce the "kernel resources exhausted"
panics that could be caused by opening a large
number of pipes. (Pipes alone are no longer able
to exhaust all resources, but other kernel memory hogs
in league with pipes may still be able to do so.)
PR: 53627
Ideas / comments from: hsu, tjr, dillon@apollo.backplane.com
MFC after: 1 week
the bulk out buffer size to 16 bytes. The bulk out endpoint descriptor
reports 32 bytes, but if you use this value, data will get dropped.
Reviewed/approved by: scottl
- Change vm_pageout_object_deactivate_pages()'s first parameter from a
vm_map_t to a pmap_t.
- Change vm_pageout_object_deactivate_pages()'s and
vm_pageout_map_deactivate_pages()'s last parameter from a vm_pindex_t
to a long. Since the number of pages in an address space doesn't
require 64 bits on an i386, vm_pindex_t is overkill.
to have this driver working on sparc64. It still needs to be made
endian-clean before it can work there.
Special thanks to dragonk@evilcode.net for sending me a dc(4) card so
that I was able to do this work.
Many cheers to all the people that tested this change, thanks to them,
this change shouldn't break anything :-).
Tested by: marcel (i386 and ia64), ru (i386), wilko (alpha),
mbr (i386), wpaul (i386) and
Will Saxon <WillS@housing.ufl.edu> (i386)
reset them only if they were previously in use. Unconditionally
resetting the registers wipes them out frequently, which interferes
with their use for kernel debugging.
While I'm here, be less verbose in the associated comment of a
neighboring function.
Noticed by: bde
insertion and extraction) has revealed two bugs:
- In vlan_start(), we're supposed to check the underlying interface to
see if it has the IFCAP_VLAN_HWTAGGING cabability set and, if so, set
things up for the VLAN_OUTPUT_TAG() routine. However the code checks
ifp->if_capabilities, which is the vlan pseudo-interface's capabilities
when it should be checking p->if_capabilities, which relates to the
underlying physical interface. Change ifp->if_capabilities to
p->if_capabilities so this works.
- In vlan_input(), we have to extract the 16-bit tag value from the
received frame and use it to figure out which vlan interface gets
the frame. The code that we use to track down the desired vlan
pseudo-interface is:
for (ifv = LIST_FIRST(&ifv_list); ifv != NULL;
ifv = LIST_NEXT(ifv, ifv_list))
if (ifp == ifv->ifv_p && tag == ifv->ifv_tag)
break;
The problem is that 'tag' is not computed consistently. In the case
where the interface supports hardware VLAN tag extraction and calls
VLAN_INPUT_TAG(), we do this:
tag = *(u_int*)(mtag+1);
But in the software emulation case, we do this
tag = EVL_VLANOFTAG(ntohs(evl->evl_tag));
The problem here is the EVL_VLANOFTAG() macro is only ever applied
in this one case. It's never applied to ifv->ifv_tag or anwhere else.
We must be consistent: either it's applied everywhere or nowhere.
To see how this can be a problem, do something like
ifconfig vlan0 vlan 12345 vlandev foo0 and observe the results.
I'm not quite sure what the right thing is to do here. Neither the
vlan(4) nor ifconfig(8) man pages suggest which way to go. For now,
I've removed this use of EVL_VLANOFTAG() so that the tag will match
correctly in all cases. I will not get upset if somebody makes a
compelling argument for using EVL_VLANOFTAG() everywhere instead,
as long as the use is consistent.
tested for playback.
* modify device name strings for ich chips to better conform with their
common names.
* remove superflous 'AC97 controller' from nforce device names.
MFC after: 1 week
to get a stacktrace. This does not work even with M_NOWAIT when we
have WITNESS and is generally a bad idea (pointed out by bde@). We
allocate an 8K heap for use by the unwinder when ddb is active. A
stack trace roughly takes up half of that in any case, so we have
some room for complex unwind situations. We don't want to waste too
much space though. Due to the nature of unwinding, we don't worry
too much about fragmentation or performance of unwinding while in
the debugger. For now we have our own heap management, but we may
be able to leverage from existing code at some later time.
While here:
o Make sure we actually free the unwind environment after unwinding.
This fixes a memory leak.
o Replace Doug's license with mine in unwind.c and unwind.h. Both
files don't have much, if any, of Doug's code left since the EPC
syscall overhaul and the import of the unwinder.
o Remove dead code.
o Replace M_NOWAIT with M_WAITOK for all remaining malloc() calls.
notice another typo in the same line. This typo makes libthr unuseable,
but it's effects where counter-balanced by the extra semicolon, which
made libthr remarkably useable for the past several months.
Should work with both regular and fast ipsec (mutually exclusive).
See manpage for more details.
Submitted by: Ari Suutari (ari.suutari@syncrontech.com)
Revised by: sam
MFC after: 1 week
- Associate logical CPUs on the same physical core with the same kseq.
- Adjust code that assumed there would only be one running thread in any
kseq.
- Wrap the HTT code with a ULE_HTT_EXPERIMENTAL ifdef. This is a start
towards HyperThreading support but it isn't quite there yet.
BUS_DMA_NOWAIT flag, since the code can't handle this.
- Use NULL, NULL for the lockfunc and lockfuncarg parameters of
bus_dma_tag_create() since deferred loads can't happen now.
as the target process' pid, it may exist if the process forked before leaving
the pgrp.
Thix fixes a panic that happens when calling setpgid to make a process
re-enter the pgrp with the same pgid as its pid if the pgrp still exists.
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
order to avoid the overhead of later page faults. In general, it
implements two cases: one for vnode-backed objects and one for
device-backed objects. Only the device-backed case is really
machine-dependent, belonging in the pmap.
This commit moves the vnode-backed case into the (relatively) new
function vm_map_pmap_enter(). On amd64 and i386, this commit only
amounts to code rearrangement. On alpha and ia64, the new machine
independent (MI) implementation of the vnode case is smaller and more
efficient than their pmap-based implementations. (The MI
implementation takes advantage of the fact that objects in -CURRENT
are ordered collections of pages.) On sparc64, pmap_object_init_pt()
hadn't (yet) been implemented.
be delivered to that thread, regardless of whether it
has it masked or not.
Previously, if the targeted thread had the signal masked,
it would be put on the processes' siglist. If
another thread has the signal umasked or unmasks it before
the target, then the thread it was intended for would never
receive it.
This patch attempts to solve the problem by requiring callers
of tdsignal() to say whether the signal is for the thread or
for the process. If it is for the process, then normal processing
occurs and any thread that has it unmasked can receive it.
But if it is destined for a specific thread, it is put on
that thread's pending list regardless of whether it is currently
masked or not.
The new behaviour still needs more work, though. If the signal
is reposted for some reason it is always posted back to the
thread that handled it because the information regarding the
target of the signal has been lost by then.
Reviewed by: jdp, jeff, bde (style)
However, they are presently necessary due to bigger bogusness in the
pci bus layer not doing the right thing on suspend/resume or on
initial device probe. This is exactly the sort of thing that the
BURN_BRIDGES option was invented for. Mark all of them as
BURN_BRIDGES. As soon as I have the powerstate stuff properly
integrated into the pci bus code, I intend to remove all these
workarounds.
locks held by each thread.
- Fix a bug in the original BSD/OS code where a contested lock was not
properly handed off from the old thread to the new thread when a
contested lock with more than one blocked thread was transferred from
one thread to another.
- Don't use an atomic operation to write the MTX_CONTESTED value to
mtx_lock in the aforementioned special case. The memory barriers and
exclusion provided by sched_lock are sufficient.
Spotted by: alc (2)
disabled.
- Change the apm driver to match the acpi driver's behavior by checking to
see if the device is disabled in the identify routine instead of in the
probe routine. This way if the device is disabled it is never created.
Note that a few places (ips(4), Alpha SMP) used "disable" instead of
"disabled" for their hint names, and these hints must be changed to
"disabled". If this is a big problem, resource_disabled() can always be
changed to honor both names.
careful to call all map_load calls with BUS_DMA_NOWAIT because we
really don't want some PDUs to wait while others go out - ATM guarantees
the ordering of cells and also of PDUs (within one VC, that is). With
BUS_DMA_NOWAIT bus_dmamap_load should never return EINPROGRESS.
Make the tag used for transmission buffers one larger than the maximum
AAL5 PDU (65535). This is needed, because all PDU sizes need to be round
up to multiple of four for the card and PDUs that are just below the
maximum size will be rounded up to 65536
real SATA disks now that I can test it.
Add support for the SiI 3112 SATA chip using memory mapped I/O.
Update the support for the SiI 0680 to use the memio interface as well.
Sponsored by: David Leimbach <leimy2k@mac.com> (3112 based controller)
Sponsored by: FreeBSD Systems (www.FreeBSDsystems.com) (SATA disks)
o use a mutex to protect the bounce pages structure.
o use a SYSINIT function to initialize the bounce pages structures
and thus avoid a race condition in alloc_bounce_pages().
o add support for the BUS_DMA_NOWAIT flag in bus_dmamap_load().
o remove obsolete splhigh()/splx() calls.
o remove printf() about incorrect locking in busdma_swi() and sync
busdma_swi() with the one of the alpha backend.
o use __FBSDID.
system by specifying the file system ID instead of a path. Use this
by default in umount(8). This avoids the need to perform any vnode
operations to look up the mount point, so it makes it possible to
unmount a file system whose root vnode cannot be looked up (e.g.
due to a dead NFS server, or a file system that has become detached
from the hierarchy because an underlying file system was unmounted).
It also provides an unambiguous way to specify which file system is
to be unmunted.
Since the ability to unmount using a path name is retained only for
compatibility, that case now just uses a simple string comparison
of the supplied path against f_mntonname of each mounted file system.
Discussed on: freebsd-arch
mdoc help from: ru
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
with a comment describing it's advantages and the implication of
changing it. While being there, fix a typo in NOTES.
The option is not enabled in NOTES for now since large portions of code
are conditional on it being disabled, too.
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.
The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
so unit numbers should match what's printed on the box more
closely.
- Real interrupt routing is implemented now, so cardbus bridges
etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
sufficient) heuristics.
- Much cleaner code.
There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.
A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.
In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
generic PCI bus driver, but uses the firmware for enumeration,
performs additional initialization for devices and firmware-specific
interrupt routing. It also implements an OFW-specific method to allow
child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
of the generic PCI-PCI bridge driver; it has it's own method for
interrupt routing, as well as some sparc64-specific methods (one to
get the node again, and one to adjust the bridge bus range, since
we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
drivers above.
- Provide a small common framework for interrupt routing (for all
bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
bunch of old kludges in pci_read_config(), and the whole
preinitialization (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
required for PCI), and move it to a more correct location (new
support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.
In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.
Reviewed in part by: imp
Tested by: jake, Marius Strobl <marius@alchemy.franken.de>,
Sergey Mokryshev <mokr@mokr.net>,
Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by: kris
interrupt to be used for a device. This is intended solely for internal
use of PCI bus implementations, and exists so that PCI bus drivers
implementing special interrupt assignment methods which require
additional work at the bus level to work right can be easily derived
from the generic driver (or any other one) without resorting to hacks.
It will be used in the sparc64 ofw_pcibus driver, which will be
committed shortly.
Make use of this method in the generic implementation, and add it to
the method table of bus drivers derived from the PCI one.
Reviewed by: imp, -hackers
are some Sun PCI devices around which bogusly set intpin to 0, although
they use the intline mechanism; this allows the device driver to correct
that.
Reviewed by: imp
bsd.lib.mk and thus broke the build since AFLAGS were not taken
into considered anymore, as bsd.lib.mk currently has wrong .s.o
rule that uses cc(1) instead of as(1).
Revision 1.14 reverted to using as(1), and revision 1.15 brought
AFLAGS back to the business, but revision 1.14 also broke "make
clean".
To fix this, but not break anything that was fixed in revisions
1.13-1.15, we revert mostly to revision 1.13 except for switching
back to using bsd.prog.mk. This gives us back the default .s.o
rule from sys.mk that uses as(1), and fixes "make clean" by
restoring the full contents of OBJS.
Also fixed LDFLAGS.
o add missing zeroize op when deleting an SA
o don't re-initialize an xform for an SA that already has one
Submitted by: Doug Ambrisko <ambrisko@verniernetworks.com>
MFC after: 1 day
implementation of a largely MI pmap_object_init_pt() for vnode-backed
objects. pmap_enter_quick() is implemented via pmap_enter() on sparc64
and powerpc.
- Correct a mismatch between pmap_object_init_pt()'s prototype and its
various implementations. (I plan to keep pmap_object_init_pt() as
the MD hook for device-backed objects on i386 and amd64.)
- Correct an error in ia64's pmap_enter_quick() and adjust its interface
to match the other versions. Discussed with: marcel
bit in the EEPROM mode register on. Also, the address must be written
in two 32-bit register accesses instead of 6 8-bit accesses.
Tested with my 8139B cardbus NIC.
PR: kern/35900
Submitted by: Mark Kettenis <kettenis@chello.nl>
the user requests a read-only mount. This is necessary because we
don't do the VOP_OPEN again if they upgrade a read-only mount to
read-write.
Fixes lockup when creating files on msdosfs mounts that have been
mounted read-only then upgraded to read-write. The exact cause of
the lockup is not known, but it is likely to be the kernel getting
stuck in an infinite loop trying to write dirty buffers to a device
without write permission.
Reported/tested by andreas, discussed with phk.
mapped I/O mode, we pause for .1 seconds after issuing the reset command
before trying to poll the 'command busy' bit in the status register.
With my 3c575C cardbus NIC, my Sony Picturebook locks up when it tries
to read the status register immediately after the reset. This appears
to be a problem only with certain NICs on certain hardware, but the
added delay should not hurt cards that already work.
This bug seems to have been brought to light by the fact that the xl
driver now defaults to memory mapped I/O mode instead of programmed
I/O mode like it used to. With PIO mode, the delay isn't needed and
everything works (which is why this NIC worked with 5.0-RELEASE but
not 5.1). I suspect that what's happening is that when the chip is
reset, it takes a little while for the memory-mapped decoding logic
to recover. Trying to access the chip's registers during this period
causes an error condition of some kind that wedges the system.
1.) Handle maximum segment sizes which are smaller than the IOMMU page
size by splitting up pages across multiple segments if needed; this case
was previously unimplemented, and would cause panics.
2.) KASSERT that the physical address is in range; remove a KASSERT that
has become pointless.
3.) Add a comment describing what remains to be fixed in the IOMMU code;
I plan to address these issues soon.
Desired by: dwhite (1)
happens to work on 32-bit platforms as sizeof(long)=sizeof(int), but
wrecks all kinds of havoc (garbage reads, corrupting writes and
misaligned loads/stores) on 64-bit architectures.
The fix for now is to use fuword32() and suword32() and change the
type of the applicable int fields to int32. This is to make it
explicit that we depend on these fields being 32-bit. We may want
to revisit this later.
Reviewed by: deischen
the VMIN and VTIME members of the c_cc array. These members are not
special control characters. By not excluding these members we
changed the noncanonical mode input processing when both members
were 0 on entry (=LINUX_POSIX_VDISABLE) as we would remap them to 255
(=_POSIX_VDISABLE). See termios(4) case A for how that screws up
your terminal I/O.
PR: 23173
Originator: Bjarne Blichfeldt <bbl@dk.damgaard.com>
Patch by: Boris Nikolaus <bn@dali.tellique.de> (original submission)
Philipp Mergenthaler <philipp.mergenthaler@stud.uni-karlsruhe.de>
Reminders by: Joseph Holland King <gte743n@cad.gatech.edu>
MFC after: 5 days
- Initialize fc->status to process bus reset correctly after resume.
- Initialize AT ring buffer pointer.
- Requeue stdma to stfree for active IR buffer.
- Stop DMA before suspend for safe.
- Set powerstate after resume.
function behaves correctly in principle, but is not expected to be
100% complete. In any case, with this commit we have KSE ported
enough to start runtime testing with threaded applications and fix
whatever bugs or omissions we encounter. Yay!
or unblock a thread in kernel, and allow UTS to specify whether syscall
should be restarted.
o Add ability for UTS to monitor signal comes in and removed from process,
the flag PS_SIGEVENT is used to indicate the events.
o Add a KMF_WAITSIGEVENT for KSE mailbox flag, UTS call kse_release with
this flag set to wait for above signal event.
o For SA based thread, kernel masks all signal in its signal mask, let
UTS to use kse_thr_interrupt interrupt a thread, and install a signal
frame in userland for the thread.
o Add a tm_syncsig in thread mailbox, when a hardware trap occurs,
it is used to deliver synchronous signal to userland, and upcall
is schedule, so UTS can process the synchronous signal for the thread.
Reviewed by: julian (mentor)
POSIX says siginfo pointer parameter can be NULL and if the
function success, it should return signal number but not zero.
The waitset it past should be negatived before it can be
used as thread signal mask.
color in vm_page_alloc(). (This also has small performance benefits.)
- Eliminate vm_page_select_free(); vm_page_alloc() might as well
call vm_pageq_find() directly.
nice distribution without significantly impacting interactive response.
As a side effect it should also allow batch processes to run for a
slightly longer period which will positively impact their performance.
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
to store an int in the bio->bio_driver1 (a void *). It is big enough,
but you have to match the int sizes first before doing the cast.
Glanced at by: scottl
mark crypto requests with ``callback immediately'' to avoid doing a context
switch to return crypto results. This completes the work to eliminate
context switches for using software crypto via the crypto subsystem (with
symmetric crypto ops).
software crypto device:
o record crypto device capabilities in each session id
o add a capability that indicates if the crypto driver operates synchronously
o tag the software crypto driver as operating synchronously
This commit also introduces crypto session id macros that cleanup their
construction and querying.
an MSDOSFS file system either failed, silently corrupted the file, or
sometimes corrupted the neighboring file.
PR: 53695
Submitted by: Ariff Abdullah <skywizard@MyBSD.org.my> (original version)
MFC: 3 days
channel has been disabled by BIOS. This prevents a bus timeout
machine check on B&W G3 PowerMacs, which have a primary-only CMD646
on the motherboard.
Approved by: sos
Obtained from: NetBSD
bus_dma async callback scheme. Note that sparc64 does not seem to do
async callbacks. Note that ia64 callbacks might not be MPSAFE at the
moment. Note that powerpc doesn't seem to do async callbacks due to
the implementation being incomplete.
Reviewed by: mostly silence on arch@
succeeds. There is a difference between how OLDCARD and NEWCARD deal
with their resources, and this code exposes that difference. I'm not
sure which behavior is correct, and will need to look into that in
more detail. However, it appears that we go ahead and allocate the
right thing in both cases that I have access to (CF cards, CDROM, and
external ata enclosures), so go ahead and ignore the failure to get
the resource for the other rid. There's already another check to make
sure that the actual allocation works correctly, and that should be
sufficient to catch cases that don't work.
Submitted by: wpaul and iedowse
o add back rx monitor support
o make WI_RID_SCAN_RES DTRT
o fix a bug handling zero-length RID requests (used by dstumbler to set
a zero-length SSID)
o make RID_SCAN_REQ DTRT
o add back WI_RID_OWN_SSID
o fix wi_scan_ap to take a channel mask and txrate (for prism cards)
These changes fix dstumbler -o (monitor mode). A minor change to dstumbler
is needed to get normal AP scanning mode to work right; this is preferred to
modifying the driver.
PR: kern/53187
Reviewed by: Bruce M Simpson <bms@spc.org>
flag'ed INTR_MPSAFE. In ep_if_start(), use the IF_DEQUEUE macro to
grab the next mbuf to send, and use IF_PREPEND if the card is busy
and we actually can't handle it right now.
The old code was first getting the mbuf by taking it from the queue
without using the macros, thus without locking, and without removing
it from the queue either. It was later assuming that IF_DEQUEUE would
give him this same mbuf.
Tested by: mich
when the user specifies a maximum fragment size < 2.
This is the behavior that Linux provides and fixes the problem I've
observed in Tribes2 where sounds effects are delayed by 1/2 a second.
This commit has two pieces. One half is the watchdog kernel code which lives
primarily in hardclock() in sys/kern/kern_clock.c. The other half is a userland
daemon which, when run, will keep the watchdog from firing while the userland
is intact and functioning.
Approved by: jeff (mentor)
being requested is outside of the range of the direct map region. eg:
for pci windows. While here, increase the minimum size of the direct
map region to be 4GB instead of 1GB.
so can leave stale data in the buffer and confuse the driver.
- enable the ability to set the 'disable' hint for the driver to keep it
from attaching. i.e. 'hw.ips.0.disable=1' will prevent the driver from
attaching.
- Only detach if attach suceeded.
Submitted by: mjacob
Before, we would add/subtract the leap second when the system had been
up for an even multiple of days, rather than at the end of the day, as
a leap second is defined (at least wrt ntp). We do this by
calculating the notion of UTC earlier in the loop, and passing that to
get it adjusted. Any adjustments that ntp_update_second makes to this
time are then transferred to boot time. We can't pass it either the
boot time or the uptime because their sum is what determines when a
leap second is needed. This code adds an extra assignment and two
extra compare in the typical case, which is as cheap as I could made
it.
I have confirmed with this code the kernel time does the correct thing
for both positive and negative leap seconds. Since the ntp interface
doesn't allow for +2 or -2, those cases can't be tested (and the folks
in the know here say there will never be a +2s or -2s leap event, but
rather two +1s or -1s leap events).
There will very likely be no leap seconds for a while, given how the
earth is speeding up and slowing down, so there will be plenty of time
for this fix to propigate. UT1-UTC is currently at "about -0.4s" and
decrementing by .1s every 8 months or so. 6 * 8 is 48 months, or 4
years.
-stable has different code, but a similar bug that was introduced
about the time of the last leap second, which is why nobody has
noticed until now.
MFC After: 3 weeks
Reviewed by: phk
"Furthermore, leap seconds must die." -- Cato the Elder
incremented at the start of the leap second, not after the leap second
has been inserted. This is because at the start of the leap second,
we set the time back one second. This setting back one second is the
moment that the offset changes. The old code set it back after the
leap second, but that's one second too late. The negative leap second
case is handled correctly.
Reviewed by: phk
of pcpu locks. This makes uma_zone somewhat smaller (by (LOCKNAME_LEN *
sizeof(char) + sizeof(struct mtx) * maxcpu) bytes, to be exact).
No Objections from jeff.
