Commit Graph

49 Commits

Author SHA1 Message Date
pfg
c1f320fca0 aic7xxx: minor spelling fixes.
Affects mostly comments but also a visible text string,

Differential Revision:	https://reviews.freebsd.org/D6270
2016-05-10 16:40:19 +00:00
gibbs
6cc9a00e92 Correct logic bug in aicasm's undefined register bit access detection code.
The code in question verifies that all register write operations only change
bits that are defined (in the register definition file) for that effected
register.  The bug effectively disabled this checking.

o Fix the check by testing the opcode against all supported read ("and" based)
  operands.

o Add missing bit definitions to the aic7xxx and aic79xx register definition
  files so that the warning (treated as a fatal error) does not spuriously
  fire.

Reported by:	Pawel Worach <pawel.worach@gmail.com>
MFC after:	1 week
2010-07-14 14:31:18 +00:00
imp
4b319958e7 Start each of the license/copyright comments with /*-, minor shuffle of lines 2005-01-06 01:43:34 +00:00
gibbs
df180be1a1 ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
	Use common OSM routines from aic_osm_lib for bus dma operations,
	delay routines, accessing CCBs, byte swapping, etc.

aic7xxx_pci.c:
	Provide a better description for the 2915/30LP on attach.

aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
	Move FBSDID behind an ifdef so that these core files will
	still compile under other OSes.

aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
	To speed up non-packetized CDB delivery in Rev B, all CDB
	acks are "released" to the output sync as soon as the
	command phase starts.  There is only one problem with this
	approach.  If the target changes phase before all data are
	sent, we have left over acks that can go out on the bus in
	a data phase.  Due to other chip contraints, this only
	happens if the target goes to data-in, but if the acks go
	out before we can test SDONE, we'll think that the transfer
	has completed successfully.  Work around this by taking
	advantage of the 400ns or 800ns dead time between command
	phase and the REQ of the new phase.  If the transfer has
	completed successfully, SCSIEN should fall *long* before we
	see a phase change.  We thus treat any phasemiss that
	occurs before SCSIEN falls as an incomplete transfer.

	aic79xx.h:
		Add the AHD_FAST_CDB_DELIVERY feature.

	aic79xx_pci.c:
		Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.

	aic79xx.seq:
		Test for PHASEMIS in the command phase for
		all AHD_FAST_CDB_DELIVERY controlelrs.

ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
	Move definition of controller BAR offsets to core header files.

aic7xxx.c:
aic79xx.c:
	In the softc free routine, leave removal of a softc from the
	global list of softcs to the OSM (the caller of this routine).
	This allows us to avoid holding the softc list_lock during device
	destruction where we may have to sleep waiting for our recovery
	thread to halt.

ahc_pci.c:
	Use ahc_pci_test_register access to validate I/O mapped in
	addition to the tests already performed for memory mapped
	access.

	Remove unused ahc_power_state_change() function.  The PCI
	layer in both 4.X and 5.X now offer this functionality.

ahd_pci.c:
	Remove reduntant definition of controller BAR offsets.  These
	are also defined in aic79xx.h.

	Remove unused ahd_power_state_change() function.  The PCI
	layer in both 4.X and 5.X now offer this functionality.

aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
	Move timeout handling to the driver cores.  In the case
	of the aic79xx driver, the algorithm has been enhanced
	to try target resets before performing a bus reset.  For
	the aic7xxx driver, the algorithm is unchanged.  Although
	the drivers do not currently sleep during recovery (recovery
	is timeout driven), the cores do expect all processing to
	be performed via a recovery thread.  Our timeout handlers
	are now little stubs that wakeup the recovery thread.

aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
	Change shared_data allocation to use a map_node so
	that the sentinel hscb can use this map node in
	ahd_swap_with_next_hscb.  This routine now swaps
	the hscb_map pointer in additon to the hscb
	contents so that any sync operations occur on
	the correct map.

	physaddr -> busaddr

	Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>

aic79xx.c:
	Make more use of the in/out/w/l/q macros for accessing
	byte registers in the chip.

	Correct some issues in the ahd_flush_qoutfifo() routine.
	    o Run the qoutfifo only once the command channel
	      DMA engine has been halted.  This closes a window
	      where we might have missed some entries.
	    o Change ahd_run_data_fifo() to not loop to completion.
	      If we happen to start on the wrong FIFO and the other
	      FIFO has a snapshot savepointers, we might deadlock.
	      This required our delay between FIFO tests to be
	      moved to the ahd_flush_qoutfifo() routine.
	    o Update/add comments.
	    o Remove spurious test for COMPLETE_DMA list being empty
	      when completing transactions from the GSFIFO with
	      residuals.  The SCB must be put on the COMPLETE_DMA
	      scb list unconditionally.
	    o When halting command channel DMA activity, we must
	      disable the DMA channel in all cases but an update
	      of the QOUTFIFO.  The latter case is required so
	      that the sequencer will update its position in the
	      QOUTFIFO.  Previously, we left the channel enabled
	      for all "push" DMAs.  This left us vulnerable to
	      the sequencer handling an SCB push long after that
	      SCB was already processed manually by this routine.
	    o Correct the polarity of tests involving
	      ahd_scb_active_in_fifo().  This routine returns
	      non-zero for true.

	Return to processing bad status completions through
	the qoutfifo.  This reduces the time that the sequencer
	is kept paused when handling transactions with bad
	status or underruns.

	When waiting for the controller to quiece selections,
	add a delay to our loop.  Otherwise we may fail to wait
	long enough for the sequencer to comply.

	On H2A4 hardware, use the slow slewrate for non-paced
	transfers.  This mirrors what the Adaptec Windows
	drivers do.

	On the Rev B. only slow down the CRC timing for
	older U160 devices that might need the slower timing.
	We define "older" as devices that do not support
	packetized protocol.

	Wait up to 5000 * 5us for the SEEPROM to become unbusy.
	Write ops seem to take much longer than read ops.

aic79xx.seq:
	For controllers with the FAINT_LED bug, turn the diagnostic
	led feature on during selection and reselection.  This covers
	the non-packetized case.  The LED will be disabled for
	non-packetized transfers once we return to the top level idle
	loop.  Add more comments about the busy LED workaround.

	Extend a critical section around the entire
	command channel idle loop process.  Previously
	the portion of this handler that directly manipulated
	the linked list of completed SCBs was not protected.
	This is the likely cause of the recent reports of
	commands being completed twice by the driver.

	Extend critical sections across the test for,
	and the longjump to, longjump routines.  This
	prevents the firmware from trying to jump to
	a longjmp handler that was just cleared by the
	host.

	Improve the locations of several critical section
	begin and end points.  Typically these changes
	remove instructions that did not need to be
	inside a critical section.

	Close the "busfree after selection, but before busfree
	interrupts can be enabled" race to just a single sequencer
	instruction.  We now test the BSY line explicitly before
	clearing the busfree status and enabling the busfree
	interrupt.

	Close a race condition in the processing of HS_MAILBOX
	updates.  We now clear the "updated" status before the
	copy.  This ensures that we don't accidentally clear
	the status incorrectly when the host sneaks in an update
	just after our last copy, but before we clear the status.
	This race has never been observed.

	Don't re-enable SCSIEN if we lose the race to disable SCSIEN
	in our interrupt handler's workaround for the RevA data-valid
	too early issue.

aic79xx_inline.h:
	Add comments indicating that the order in which bytes are
	read or written in ahd_inw and ahd_outw is important.  This
	allows us to use these inlines when accessing registers with
	side-effects.

aic79xx_pci.c:
	The 29320 and the 29320B are 7902 not 7901 based products.
	Correct the driver banner.

aic7xxx.h:
	Enable the use of the auto-access pause feature
	on the aic7870 and aic7880.  It was disabled due
	to an oversight.

aic7xxx.reg:
	Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
	avoid leaving garbage in MWI_RESIDUAL.  This
	prevents spurious overflows whn operating target
	mode on controllers that require the MWI_RESIDUAL
	work-around.

aic7xxx.seq:
	AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
	Reference the correct softc field when testing
	for its presence.

	Set the NOT_IDENTIFIED and NO_CDB_SENT bits
	in SEQ_FLAGS to indicate that the nexus is
	invalid in await busfree.

aic7xxx_93cx6.c:
	Add support for the C56/C66 versions of the EWEN and EWDS
	commands.

aic7xxx.c:
aic7xxx_pci.c:
	Move test for the validity of left over BIOS data
	to ahc_test_register_access().  This guarantees that
	any left over CHIPRST value is not clobbered by our
	register access test and lost to the test that was
	in ahc_reset.
2003-12-17 00:02:10 +00:00
gibbs
833b47a80a Correct/Simplify ignore wide residue message handling
aic7xxx.c:
	In ahc_handle_ign_wide_residue():
	o Use SCB_XFERLEN_ODD SCB field to determine transfer
	  "oddness" rather than the DATA_COUNT_ODD logic.
	  SCB_XFERLEN_ODD is toggled on every ignore wide
	  residue message so that multiple ignore wide residue
	  messages for the same transaction are properly supported.
	o If the sg list has been exausted, the sequencer
	  doesn't bother to update the residual data count
	  since it is known to be zero.  Perform the zeroing
	  manually before calculating the remaining data count.
	o Ensure that SG_LIST_NULL is cleared in the
	  residual sg pointer for "mid-transfer" ignore
	  wide residue cases.
	o Use multibyte in/out macros instead of shifting/masking
	  by hand.

aic7xxx.h:
	Modify the SCB_GET_LUN() macro to mask the lun hardware
	SCB field with LID.  This leaves two bits in the LUN
	field that can be used for other purposes.

aic7xxx.reg:
	Change LID to be 0x3F.  This is the maximum supported
	lun size for non-packetized SCSI.  Map the top bit
	of the lun to SCB_XFERLEN_ODD.  The host must set
	this bit whenever a transfer is an odd length.

	Remove the ODD_SEG bit field that was used to carry the odd
	transfer length information through the SG cache.  This
	is obviated by SCB_XFERLEN_ODD field.

	Remove the DATA_COUNT_ODD scratch ram byte that was used
	dynamicaly compute data transfer oddness.  This is obviated
	by SCB_XFERLEN_ODD field.

aic7xxx.seq:
	Be more careful in our handling of the SCB_LUN field.  It
	must be masked with LID if only lun information is desired.

	Remove all updates to the DATA_COUNT_ODD scratch ram field.
	Remove all uses of ODD_SEG.  These two save quite a few
	sequencer instructions.

	Use SCB_XFERLEN_ODD to validate the end of transfer
	ignore wide residue message case.

aic7xxx_inline.h:
	In ahc_queue_scb(), setup the SCB_XFERLEN_ODD field.

Approved by: RE
2003-05-26 21:24:01 +00:00
gibbs
0ad8e69a7c aic7xxx.c:
aic7xxx.h:
	Split out core chip initialization into ahc_chip_init().
	This will allow us to reset the chip correctly at times
	other than initial chip setup.

aic7770.c
aic7xxx_pci.c:
	Flesh out bus chip init methods for our two
	bus attachments and use these, in addition to
	bus suspend/resume hooks to get the core in
	better shape for handling these events.

	When disabling PCI parity error checking, use FAILDIS.
	Although the chip docs indicate that clearing PERRESPEN
	should also work, it does not.

	Auto-disable pci parity error checking after informing
	the user of AHC_PCI_TARGET_PERR_THRESH number of parity
	errors observed as a target.

aic7xxx.h:
aic7xxx_pci.c
aic7770.c
aic7xxx.c
	Add the instruction_ram_size softc field.

	Remove the now unused stack_size softc field.

	Modify ahc_loadseq to return a failure code
	and to actually check the downloaded instruction
	count against the limit set in our softc.

	Modify callers of ahc_loadseq to handle load
	failures as appropriate.

	Set instruction RAM sizes for each chip type.

aic7xxx_pci.c:
	Add some delay in the aic785X termination
	control code.  This may fix problems with
	the 2930.

	Be consistent in how we access config space
	registers.  16bit registers are accessed using
	16bit ops.

aic7xxx.c:
	Correct spelling errors.

	Have ahc_force_renegotiation() take a devinfo as is done
	in the U320 driver.  Use this argument to correct a bug
	in the selection timeout handler where we forced a renegotiation
	with the last device that had set SAVED_SCSIID.  SAVED_SCSIID
	is only updated once a selection is *sucessfull* and so is
	stale for any selection timeout.

	Cleanup the setup of the devinfo for busfree events.  We
	now use this devinfo for a call to ahc_force_renegotiation()
	at the bottom of the routine, so it must be initialized in
	all cases.

	In ahc_pause_and_flushwork(), adjust the loop so that it
	will exit in the hot-eject case even if the INT_PEND mask
	is something other than 0xFF (as it is in this driver).

	Correct a wrapping string constant.

	Call ahc_fini_scbdata() after shutdown so that
	any ahc_chip_init() routine that might access
	SCB data will not access free'd memory.

	Correctly setup our buffer tag to indicate that 39bit
	addressing is available if in 39bit addressing mode.

	Rearrange some variable declarations based on
	type size.

aic7xxx.c
aic7xxx.h:
aic7xxx.reg:
	Consistently use MAX_OFFSET for the user max syncrate
	set from non-volatile storage.  This ensures that the
	offset does not conflict with AHC_OFFSET_UNKNOWN.

	Change AHC_OFFSET_UNKNOWN to 0xFF.  This is
	a value that the curr->offset can never be,
	unlike '0' which we previously used.  This
	fixes code that only checks for a non-zero
	offset to determine if a sync negotiation
	is required since it will fire in the unknown
	case even if the goal is async.

	Change MAX_OFFSET to 0x7f which is the max
	offset U160 aic7xxx controllers can negotiate.
	This ensures that curr->offset will not
	match AHC_OFFSET_UNKNOWN.

aic7xxx_inline.h:
	Have our inline interrupt handler return with a value
	indicating whether we serviced a real interrupt.  This
	is required for Linux support.

	Return earlier if the interrupt is not for us.
2003-05-03 23:55:38 +00:00
gibbs
e7aa337746 aic7xxx.reg:
Add a constant for the controller's stack size and the
	maximum scsi offset.

aic7xxx.seq:
	Style nit.  The source is implied to be the destination
	unless overridden in an "and" instruction.

	Update target mode code for changes in identify seen
	sequencer flags.

aic7xxx_pci.c:
	Ensure that the PCIERRGENDIS bit is set in the
	PCIERRGEN config space register.  Perhaps this
	is a reason for the spurios parity errors reported
	on U160 controllers.

	Honor the AHC_NO_BIOS_INIT flag.

	Allow PCI interrupt reporting to be disabled,
	by clearing the PERRRESEN bit in the command
	register.  This option is now enabled via a new
	softc flag: AHC_DISABLE_PCI_PERR.

	Disable SERR and pause the controller prior to performing
	our mmapped I/O test.  This should handle the case of
	controllers that do not "auto-access pause".  For legacy
	controllers, use SCB ram instead of scratch ram since
	the latter may contain settings left over from the BIOS
	that we will use if an seeprom is not found.

	Make use of new ahc_inl/outl() inlines.

aic7xxx.h:
	Reformat a few comments to follow driver style.

	Add a controller flags that indicate that a controller
	has not been initialized by the BIOS and whether to
	disable PCI parity errors..

	Remove stack probing softc members.

	Add a few more syncrate constants that are useful in speed
	fallback calculations.

	Add the SHOW_MASKED_ERRORS debug flag.

aic7xxx.h:
aic7xxx.c:
	Implement the SCB_SILENT flag.  This is useful for
	hushing up the driver during DV or other operations
	that we expect to cause transmission errors.  The
	messages will still print if the SHOW_MASKED_ERRORS
	debug option is enabled.

aic7xxx_inline.h:
	Implement ahc_[in|out][w|l|q].  This removes the need
	for manual 'or and shift" type operations throughout
	the driver.

aic7xxx.c:
	Move SELTO dignostic so that the SCB is still valid
	when we use it for printing path information.

	If we are narrow, limit syncrate to Ultra2.

	Don't clobber ppr_options when forcing a renegotiation.
	The current ppr_options may be referenced while queuing
	new commands.  Don't set our width to unknown when forcing
	negotiation on narrow controllers.  This will confuse the
	negotiation code into negotiating with a wide message on
	narrow controllers.

	Add an "asserting atn" diagnostic with controller/target
	information.

	Remove the probe_stack code.  The stack is always
	4 deep on legacy controllers, so probing is pointless.
	This also avoids an issue where probing the stack would
	upset the aic7770.

	In ahc_reset(), record whether or not we found the
	controller in a reset state.  If the controller was
	already reset, assume that no BIOS has initialized
	the controller and ignore left over scratch ram
	settings.

	Fix an ifdef bug that caused sequencer debugging to
	be enabled always.

	Clear the ultraenb flag in our tstate during startup.
	The ultraenbled'ness of a device is recorded in the user
	transfer settings.  tstate->ultraenb bitmask indicates
	which devices we have negotiated an ultra speed with.
	Just after initialization, we are async.  Setting the
	ultraenb flag while async seems to be harmless, but it
	was confusing to see the ULTRAENB flag set in the SCB.

	Enhance residual diagnostic to indicate if the residual
	if for sense information or normal data transfers.

	Indicate the features, bugs, and flags set in the softc
	that are used to control firmware patch download when
	booting verbose.

	In ahc_dump_card_state() fix a logic reversal.  The
	SCSIPHASE register only exists on U160 controllers.
	The SCSISIGI register exists on all controllers.  Not
	the other way around.  Also print out the ERROR register.

	Allow ahc_dump_card_state() to be called when the sequencer
	is not paused.  Add dump card state markers as in the U320
	driver.
2003-01-20 20:44:55 +00:00
scottl
4098cc8cf1 Bring in many bugfixes and changes obtained from formal testing:
aic7xxx.c:
        aic7xxx.h:
        aic7xxx.reg:
        aic7xxx.seq:
                Bring in the protocol violation handler from the U320
                driver and replace the NO_IDENT sequencer interrupt code
                with the PROTO_VIOLATION code.  Support for this code
                required the following changes:

                SEQ_FLAGS:
                        IDENTIFY_SEEN -> NOT_IDENTIFIED
                        Added NO_CDB_SENT

                SCB_CONTROL:
                        TARGET_SCB == STATUS_RCVD for initiator mode

                scb->flags:
                        Added SCB_TARGET_SCB since we cannot rely on
                        TARGET_SCB as a target/initiator differentiator
                        due to it being overloaded in initiator mode to
                        indicate that status has been received.

        aic7xxx.seq:
                Move data fifo CLRCHN to mesgin_rdptrs which is a safer
                location for doing this operation.  This also saves a
                sequencer instruction.

        aic7xxx.c:
        aic7xxx.h:
                Change ahc/ahd_upate_neg_request() to take a "negotiation
                type" enum that allows us to negotiate:
                        o only if the goal and current parameters differ.
                        o only if the goal is non-async
                        o always - even if the negotiation will be for async.
        aic7xxx.seq:
                Reset the FIFO whenever a short CDB transfer occurs
                so that the FIFO contents do not corrupt a future CDB
                transfer retry.

                Add support for catching the various protocol violations
                handled by ahc_handle_protocol_violation.

                Reformat some comments.

        aic7xxx.c:
        aic7xxx.h:
                Just for safety, have the aic7xxx driver probe
                the stack depth.

        aic7xxx.c:
        aic7xxx.h:
                Save and restore stack contents during diagnostics.
                Some chip variants overwrite stale entries on a
                stack "pop".

                Don't use 0 to probe the stack depth.  0 is the typical
                value used to backfill the stack if entries are overwritten
                on a "pop".

        aic7xxx.h:
                Add a missing typedef.

                Collapse SCB flag entries so they are bit contiguous.

                Add AHD_ULTRA2_XFER_PERIOD for narrow fallback calculations

        aic7xxx.c:
                Don't panic (as a diagnostic to catch bugs) if we decided to
                force the renegotiation of async even if we believe we are
                already async.  This should allow us to negotiate async instead
                of the full user goal rate during startup if bus resets are
                disabled.

                Add a space to the end of the ahc/ahd_print_devinfo routines
                so that it behaves as expected by the code that uses it.

                Only force a renegotiation on a selection timeout
                if the SCB was valid.  Doing otherwise may be dangerous
                as the connection was not valid for an unknown reason.

                Add additional diagnostic output to ahc_dump_card_state(),
                and have it use the register pretty printing functions.

                Update ahc_reg_print() to handle a NULL cur_col.

                Add a newline to ahc_dump_card_state() output.

                Bring back "use_ppr".  We need to use_ppr anytime
                doppr is true or we have non-zero protocol options.
                The later case was not handled in the recent removal
                of use_ppr.

                Move a comment and remove a useless clearing of use_ppr.

                Don't disable ENBUSFREE when single stepping on
                a DT capable controller.  We cannot re-enable unexpected
                busfree detection, so we must clear BUSFREE on each
                step instead.

                Correct the lookup of the SCB ID in ahc_handle_proto_error.

                Remove a diagnostic printf.
                Remove unecessary restoration of the STACK for older
                chips.

Approved by:	re (blanket)
2002-11-30 19:30:09 +00:00
gibbs
c07c92459e Convert to new assembler field syntax.
Document the SXFRCTL2 register found on U2 and U160 controllers.

Overload the MWI_RESIDUAL field for use as the SCB to be downloaded
for "immediate" (or those without the disconnect privledge)
transactions.

Add scratch ram locations for the 274X that give us a bit more
information including whether to enable extended translation.
2002-08-31 06:42:38 +00:00
gibbs
27ca4db257 Major update to the aic7xxx driver:
ahc_eisa.c:
ahc_pci.c:
	Conform to new aic7xxx IRQ API.

	Adapt to aic7xxx_freebsd -> aic7xxx_osm changes.

aic7770.c:
	Disable card generated interrupt early in our probe for
	"extra safety"

	Commonize some seeprom code with the PCI side of the driver.

aic7xxx.c:
	Correctly initialize a few scratch ram locations during
	a sequencer restart.  This avoids spurious sequencer ram
	parity errors in some configurations.

	Include the softc in ahc_update_residual calls.  We need it
	for some diagnostics in this code path.

	Flag a data overrun on an auto-request sense failure as a
	CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR.

	Force a renegotiation after noticing a parity error.  This
	covers targets that lose our negotiation settings but don't
	bother to give us a unit attention condition.  This can happen
	if a target fails during a reselection of us during a cable
	pull.

	Convert some code to using constants.

	Fix some typos.

	Correct target mode message loop handling.  ahc_clear_msg_state
	was not clearing the "need to go to message out phase" bit once
	our loop was over.

	Simplify some abort handling code.

	Include tag information in target mode immediate notify events.

	When shutting down EISA controllers, don't EISA BIOS settings in
	the high portions of scratch ram.  This fixes warm boot issues on
	some systems.

	Save a bit of space by only allocating the SCBs that we can use.

	Avoid some code paths in ahc_abort_scbs() if we are currently
	acting as a target.

	Correctly cleanup stranded SCBs in the card's SCB array.  These
	are SCBs who's mapping has already been torn down by code that
	aborted the SCB by seeing it in another list first.

	Add a comment about some potential bus reset issues for target
	mode on Twin (EISA only) controllers.

aic7xxx.h:
	Cleanup the hardware scb definitions a bit.

	Allocate a ful 256 byte scb mapping index.  This simplifies
	the lookup code since the table covers all possible (and potentially
	bogus) values.

	Make AHC_DEBUG work again.

aic7xxx.reg:
	Updates to hardware SCB definition.

	New definitions for target mode fixes.

aic7xxx.seq:
	In target mode, initialize SAVED_LUN just after we receive
	the identify message.  It may be required in the error recovery
	path when a normal cdb packet (includes lun) is not sent up to
	the host for processing.

	Respond to irregular messages during a selection in target mode.

	Defer looking for space for a cdb packet until we are about to
	enter command phase.  We want to be able to handle irregular messages
	even if we would otherwise return QUEUE_FULL or BUSY.

	Add support for sending Ignore Wide Residue messages as a target.

	In the disable disconnect case in target mode, set our transfer
	rate correctly once data are availble.

aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
	Add the ability to write and erase the seeprom.

aic7xxx_inline.h:
	Correct Big Endian handling of large cdb sizes (> 12 bytes).

	Adaptec to changes in the calc_residual API.

	Correct a target mode bug where we always attempted to service
	the input queue even if no progress could be made due to lack
	of ATIOs.

aic7xxx_osm.c:
	Adaptec to new IRQ mapping API.  The new API allows the core
	to only enable our IRQ mapping once it is safe (sufficient
	initialization) to do so.

	Slap bootverbose protection around some diagnostics.

	Only attempt DT phases if we are wide.

aic7xxx_osm.h:
	Enable big endian support.

	Adjust for IRQ API change.

aic7xxx_pci.c:
	Be more careful about relying on subvendor 9005 information.
	We now only trust it for HBAs.  This should allow the driver
	to attach to some MBs where the subvendor/device information
	does not follow the Adaptec spec.

	Only enable interrupts on the card once we are fully setup.

	Disable external SCB ram usage on the aic7895.  I have not
	been able to make it 100% reliable.

	Adjust to seeprom routines being properly prefixed with "ahc".

	Fix a few bugs in the external SCB ram probing routine.  We
	need to clear any parity errors we've triggered during the
	probe to avoid future, fatal, interrupts.

	If we detect an invalid cable combination, pretent there are
	no cable at all.  This will enable all of the terminators
	which is probably the safest configuration we can "guess".

MFC after: 4 days
2002-04-24 16:58:51 +00:00
gibbs
cb6621f7e0 ahc_pci.c:
If bus_dma will give us addresses > 32 bits, setup our dma tag
	to accept up to 39bit addresses.

aic7770.c:
	Update the softc directly rather than use an intermediate
	"probe_config" structure.

aic7xxx.c:
	Complete core work to support 39bit addresses for bulk data
	dma operations.  Controller data structures still must reside
	under the 4GB boundary to reduce code/data size in the sequencer
	and related data structures.  This has been tested under Linux
	IA64 and will be tested on IA64 for FreeBSD as soon as our port
	can run there.

	Add bus dmamap synchronization calls around manipulation of
	all controller/kernel shared host data structures.

	Implement data pointer reinitialation for a second data phase
	in a single connection in the kernel rather than bloat the
	sequencer.  This is an extremely rare operation (does it ever
	happen?) and the sequencer implementation was flawed for some
	of the newest chips.

	Don't ever allow our target role to initiate a PPR.  This
	is forbidden by the SCSI spec.

	Add a few missing endian conversions in the ignore wide pointers
	code.  The core has been tested on the PPC under Linux and should
	work for FreeBSD PPC.  As soon as I can test the OSM layer for
	FreeBSD PPC, I will.

	Move some of ahc_softc_init() into ahc_alloc() now that the
	probe_config structure is gone.

	Add a 4GB boundary condition on all of our dma tags.  32bit
	DAC under PCI only works on a single 4GB "page".  Although
	we can cross 4GB on a true 64bit bus, the card won't always
	be installed in one and we can save code space and cost in
	implementing high address support by assuming the high DWORD
	address will never change.

	Add diagnostics to ahc_search_qinfifo().

	Correct a target mode issue with bus resets.  To avoid an
	interrupt storm from a malicious third party holding the
	reset line, the sequencer would defer re-enabling the reset
	interrupt until either a select-out or select-in.  Unfortunately,
	the select-in enable bit is cleared by a bus reset, so a second
	reset will render the card deaf to an initiator's attempts to
	contact it.  We now re-enable bus reset interrupts immediately
	if the target role is enabled.

aic7xxx.h:
	Remove struct ahc_probe_config.

	SCB's now contain a pointer to the sg_map_node so we can perfrom
	bus dma sync operations on the SG list prior to queuing a command.

aic7xxx.reg:
	Register the Perforce ID for this file with the VERSION keyword
	so it is printed in generated files.

	Add the DSCOMMAND1 register which is used to access the high
	DWORD of address bits.

	Add the data pointer reinitialize sequencer interrupt code.

aic7xxx.seq:
	Register the Perforce ID for this file with the VERSION keyword
	so it is printed in generated files.

	Remove code to re-enable the bus reset interrupt after a select-in.
	In target mode we cannot defer this operation as ENSELI is cleared
	by a bus reset.

	Complete 39bit support.

	Generate a sequencer inteerrupt rather than handle the data
	pointers re-initialitation in the sequencer.

	Inline the "seen identify" assertion to save a few cycles.

	Short circuit the update of our residual data if we have
	fully completed a transfer.  The residual is correct from
	our last S/G load operation.

	Short circuit full SDPTR processing if the residual is 0.
	Just mark the transfer as complete.

aic7xxx_93cx6.c:
	Synchronize perforce IDs.

aic7xxx_freebsd.c:
	Complete untested 39bit support.

	Add missing endia conversions.

	Clear our residuals prior to starting a command.  The
	update residual code in the core only sets the residual
	if there is one.

aic7xxx_freebsd.h:
	Modeify ahc_dmamap_sync() macros to take an offset and a length.
	This is how sync operations are performed in NetBSD, and we should
	update our bus dma implementation to match.

aic7xxx_inline.h:
	Add data structure synchronization helper functions.

	Fix a bug in ahc_intr() where we would not clear our unsolicited
	interrupt counter after running our PCI interrupt handler.  This
	may have been the cause of the spurious PCI interrupt messages.

aic7xxx_pci.c:
	Adjust for loss of probe_config structure.

	Guard against bogus 9005 subdevice information as seen on some
	IBM MB configurations.

	Add 39bit address support.

MFC after: 10 days
2001-07-18 21:39:48 +00:00
gibbs
db9a4ae14e ahc_eisa.c:
ahc_pci.c:
	Prepare for making ahc a module by adding module dependency
	and version info.

aic7770.c:
	Remove linux header ifdefs.  The headers are handled differently
	in Linux where local includes (those using "'s instead of <>'s)
	are allowed.

	Don't map our interrupt until after we are fully setup to
	handle interrupts.  Our interrupt line may be shared so
	an interrupt could occur at any time.

aic7xxx.c:
	Remove linux header ifdefs.

	current->curr to avoid Linux's use of current as a
	#define for the current task on some architectures.

	Add a helper function, ahc_assert_atn(), for use in
	message phases we handle manually.  This hides the fact
	that U160 chips with the expected phase matching disabled
	need to have SCSISIGO updated differently.

	if (ahc_check_residual(scb) != 0)
		ahc_calc_residual(scb);
	else
		ahc_set_residual(scb, 0);

       	becomes:

	ahc_update_residual(scb);

	Modify scsi parity error (or CRC error) handling to
	reflect expected phase being disabled on U160 chips.

	Move SELTO handling above BUSFREE handling so we can
	use the new busfree interrupt behavior on U160 chips.

	In ahc_build_transfer_msg() filter the period and ppr_options
	prior to deciding whether a PPR message is required.
	ppr_options may be forced to zero which will effect our
	decision.

	Correct a long standing but latent bug in ahc_find_syncrate().
	We could choose a DT only rate even though DT transfers were
	disabled.  In the CAM environment this was unlikely as CAM
	filters our rate to a non-DT value if the device does not
	support such rates.

	When displaing controller characteristics, include the
	speed of the chip.  This way we can modify the transfer
	speed based on optional features that are enabled/disabled
	in a particular application.

	Add support for switching from fully blown tagged queing
	to just using simple queue tags should the device reject
	an ordered tag.

	Remove per-target "current" disconnect and tag queuing
	enable flags.  These should be per-device and are not
	referenced internally be the driver, so we let the OSM
	track this state if it needs to.

	Use SCSI-3 message terminology.

aic7xxx.h:
	The real 7850 does not support Ultra modes, but there are
	several cards that use the generic 7850 PCI ID even though
	they are using an Ultra capable chip (7859/7860).  We start
	out with the AHC_ULTRA feature set and then check the
	DEVSTATUS register to determine if the capability is really
	present.

	current -> curr

	ahc_calc_residual() is no longer static allowing it to
	be called from ahc_update_residual() in aic7xxx_inline.h.

	Update some serial eeprom definitions for the latest
	BIOS versions.

aic7xxx.reg:
	Add a combined DATA_PHASE mask to the SCSIPHASE register
	definition to simplify some sequencer code.

aic7xxx.seq:
	Take advantage of some performance features available only
	on the U160 chips.  The auto-ack feature allows us to ack
	data-in phases up to the data-fifo size while the sequencer
	is still setting up the DMA engine.  This greatly reduces
	read transfer latency and simplifies testing for transfer
	complete (check SCSIEN only).  We also disable the expected
	phase feature, and enable the new bus free interrupt behavior,
	to avoid a few instructions.

	Re-arrange the Ultra2+ data phase handling to allow us to
	do more work in parallel with the data fifo flushing on a
	read.

	On an SDTR, ack the message immediately so the target can
	prepare the next phase or message byte in parallel with
	our work to honor the message.

aic7xxx_93cx6.c:
	Remove linux header ifdefs.

aic7xxx_freebsd.c:
	current -> curr

	Add a module event handler.

	Handle tag downgrades in our ahc_send_async() handler.
	We won't be able to downgrade to "basic queuing" until
	CAM is made aware of this queuing type.

aic7xxx_freebsd.h:
	Include cleanups.

	Define offsetof if required.

	Correct a few comments.

	Update prototype of ahc_send_async().

aic7xxx_inline.h:
	Implement ahc_update_residual().

aic7xxx_pci.c:
	Remove linux header ifdefs.

	Correct a few product strings.

	Enable several U160 performance enhancing features.

	Modify Ultra capability determination so we will enable
	Ultra speeds on devices with a 7850 PCI id that happen
	to really be a 7859 or 7860.

	Don't map our interrupt until after we are fully setup to
	handle interrupts.  Our interrupt line may be shared so
	an interrupt could occur at any time.
2001-05-15 19:41:12 +00:00
gibbs
4641978b34 aic7770.c:
aic7xxx_pci.c:
	Enable board generation of interrupts only once our handler is
	in place and all other setup has occurred.

aic7xxx.c:
	More conversion of data types to ahc_* names.  tmode_tstate and
	tmode_lstate are the latest victims.

	Clean up the check condition path by branching early rather
	than indenting a giant block of code.

	Add support for target mode initiated sync negotiation.
	The code has been tested by forcing the feature on for
	all devices, but for the moment is left inaccesible until
	a decent mechanism for controlling the behavior is complete.
	Implementing this feature required the removal of the
	old "target message request" mechanism.  The old method
	required setting one of the 16 bit fields to initiate
	negotiation with a particular target.  This had the nice
	effect of being easy to change the request and have it
	effect the next command.  We now set the MK_MESSAGE bit
	on any new command when negotiation is required.  When
	the negotiation is successful, we walk through and clean
	up the bit on any pending commands.  Since we have to walk
	the commands to reset the SCSI syncrate values so no additional
	work is required.  The only drawback of this approach is that
	the negotiation is deferred until the next command is queued to
	the controller.  On the plus side, we regain two bytes of
	sequencer scratch ram and 6 sequencer instructions.

	When cleaning up a target mode instance, never remove the
	"master" target mode state object.  The master contains
	all of the saved SEEPROM settings that control things like
	transfer negotiations.  This data will be cloned as the
	defaults if a target mode instance is re-instantiated.

	Correct a bug in ahc_set_width().  We neglected to update
	the pending scbs to reflect the new parameters.  Since
	wide negotiation is almost always followed by sync
	negotiation it is doubtful that this had any real
	effect.

	When in the target role, don't complain about
	"Target Initiated" negotiation requests when an initiator
	negotiates with us.

	Defer enabling board interrupts until after ahc_intr_enable()
	is called.

	Pull all info that used to be in ahc_timeout for the FreeBSD
	OSM into ahc_dump_card_state().  This info should be printed
	out on all platforms.

aic7xxx.h:
	Add the SCB_AUTO_NEGOITATE scb flag.  This allows us to
	discern the reason the MK_MESSAGE flag is set in the hscb
	control byte.  We only want to clear MK_MESSAGE in
	ahc_update_pending_scbs() if the MK_MESSAGE was set due
	to an auto transfer negotiation.

	Add the auto_negotiate bitfield for each tstate so that
	behavior can be controlled for each of our enabled SCSI
	IDs.

	Use a bus interrupt handler vector in our softc rather
	than hard coding the PCI interrupt handler.  This makes
	it easier to build the different bus attachments to
	the aic7xxx driver as modules.

aic7xxx.reg:
	Remove the TARGET_MSG_REQUEST definition for sequencer ram.

aic7xxx.seq:
	Fix a few target mode bugs:

		o If MK_MESSAGE is set in an SCB, transition to
		  message in phase and notify the kernel so that
		  message delivery can occur.  This is currently
		  only used for target mode initiated transfer
		  negotiation.

		o Allow a continue target I/O to compile without
		  executing a status phase or disconnecting.  If
		  we have not been granted the disconnect privledge
		  but this transfer is larger than MAXPHYS, it may
		  take several CTIOs to get the job done.

	Remove the tests of the TARGET_MSG_REQUEST field in scratch ram.

aic7xxx_freebsd.c:
	Add support for CTIOs that don't disconnect.  We now defer
	the clearing of our pending target state until we see a
	CTIO for that device that has completed sucessfully.

	Be sure to return early if we are in a target only role
	and see an initiator only CCB type in our action routine.

	If a CTIO has the CAM_DIS_DISCONNECT flag set, propogate
	this flag to the SCB.  This flag has no effect if we've
	been asked to deliver status as well.  We will complete
	the command and release the bus in that case.

	Handle the new auto_negotiate field in the tstate correctly.

	Make sure that SCBs for "immediate" (i.e. to continue a non
	disconnected transaction) CTIO requests get a proper mapping
	in the SCB lookup table.  Without this, we'll complain when
	the transaction completes.

	Update ahc_timeout() to reflect the changes to ahc_dump_card_state().

aic7xxx_inline.h:
	Use ahc->bus_intr rather than ahc_pci_intr.
2001-03-29 00:36:35 +00:00
gibbs
90b2a0547e This is an MFC candidate.
aic7xxx.c:
	Correct code that traverses the phase table.  A much too quick
	push to staticize this structure resulted in non-functional
	lookup code.  This corrects the printing of the phase where
	a timeout occurred.

aic7xxx.reg:
	Use FIFOQWDEMP as the name for bit 5 of DFSTATUS just like
	the Adaptec data books.

aic7xxx.seq:
	Refine the 2.1 PCI retry bug workaround for certain, non-ULTRA2,
	controllers.  When the DMA of an SCB completes, it can take
	some time for HDONE to come true after MREQPEN (PCI memory request
	pending) falls.  If HDONE never comes true, we are in the hung
	state and must manually drain the FIFO.  We used to test HDONE for
	3 clock cycles to detect this condition.  This works on all of the
	hardware I can personally test.  Some controllers were reported
	to take 4 clock cycles, so the last version of this code waited
	4 clock cycles.  This still didn't work for everyone.  To fix this,
	I've adjusted the work around so that even if the hardware hasn't
	hung, but we run the work-around code, the result is a long winded
	way to complete the transfer, rather than a hang.
2001-03-19 04:40:35 +00:00
gibbs
1360758655 This is an MFC candidate.
ahc_eisa.c:
	Change aic7770_map_int to take an additional irq parameter.
	Although we can get the irq from the eisa dev under FreeBSD,
	we can't do this under linux, so the OSM interface must supply
	this.

ahc_pci.c:
	Move ahc_power_state_change() to the OSM.  This allows us to
	use a platform supplied function that does the same thing.
	-current will move to the FreeBSD native API in the near
	future.

aic7770.c:
	Sync up with core changes to support Linux EISA.

	We now store a 2 bit primary channel number rather
	than a bit flag that only allows b to be the primary
	channel.   Adjust for this change.

aic7xxx.c:
	Namespace and staticization cleanup.  All exported symbols
	use an "ahc_" prefix to avoid collisions with other modules.

	Correct a logic bug that prevented us from dropping
	ATN during some exceptional conditions during message
	processing.

	Take advantage of a new flag managed by the sequencer
	that indicates if an SCB fetch is in progress.  If so,
	the currently selected SCB needs to be returned to the
	free list to prevent an SCB leak.  This leak is a rarity
	and would only occur if a bus reset or timeout resulting
	in a bus reset occurred in the middle of an SCB fetch.

	Don't attempt to perform ULTRA transfers on ultra capable
	adapters missing the external precision resistor required
	for ultra speeds.  I've never encountered an adapter
	configured this way, but better safe than sorry.

        Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
        in scratch ram.

        If we lookup a period of 0 in our table (async), clear the scsi offset.

aic7xxx.h:
	Adjust for the primary channel being represented as
	a 2 bit integer in the flags member of the ahc softc.

	Cleanup the flags definitions so that comment blocks are
	not cramped.

	Update seeprom definitions to correctly reflect the fact
	that the primary channel is represented as a 2 bit integer.

	Add AHC_ULTRA_DIASABLED softc flag to denote controllers
	missing the external precision resistor.

aic7xxx.reg:
	Add DFCACHETH to the definition of DFSTATUS for completness sake.

	Add SEQ_FLAGS2 which currently only contains the SCB_DMA
	(SCB DMA in progress) flag.

aic7xxx.seq:
	Correct a problem when one lun has a disconnected untagged
	transaction and another lun has disconnected tagged transactions.
	Just because an entry is found in the untagged table doesn't
	mean that it will match.  If the match on the lun fails, cleanup
	the SCB (return it to the disconnected list or free it), and snoop
	for a tag message.  Before this change, we reported an unsolicited
	reselection.  This bug was introduced about a month ago during an
	overly aggressive optimization pass on the reselection code.

	When cleaning up an SCB, we can't just blindly free the SCB.  In
	the paging case, if the SCB came off of the disconnected list, its
	state may never have been updated in host memory.  So, check the
	disconnected bit in SCB_CONTROL and return the SCB to the disconnected
	list if appropriate.

	Manage the SCB_DMA flag of SEQ_FLAGS2.

	More carefully shutdown the S/G dma engine in all cases by using
	a subroutine.  Supposedly not doing this can cause an arbiter hang
	on some ULTRA2 chips.

	Formatting cleanup.

	On some chips, at least the aic7856, the transition from
	MREQPEND to HDONE can take a full 4 clock cycles.  Test
	HDONE one more time to avoid this race.  We only want our
	FIFO hung recovery code to execute when the engine is
	really hung.

aic7xxx_93cx6.c:
	Sync perforce ids.

aic7xxx_freebsd.c:
	Adjust for the primary channel being a 2 bit integer
	rather than a flag for 'B' channel being the primary.

	Namespace cleanup.

	Unpause the sequencer in one error recovery path that
	neglected to do so.  This could have caused us to perform
	a bus reset when a recovery message might have otherwise been
	successful.

aic7xxx_freebsd.h:
	Use AHC_PCI_CONFIG for controlling compilation of PCI
	support consistently throughout the driver.

	Move ahc_power_state_change() to OSM.

aic7xxx_inline.h
	Namespace cleanup.

	Adjust our interrupt handler so it will work in the edge
	interrupt case.  We must process all interrupt sources
	when the interrupt fires or risk not ever getting an
	interrupt again.  This involves marking the fact
	that we are relying on an edge interrupt in ahc->flags
	and checking for this condition in addition to the
	AHC_ALL_INTERRUPTS flag.  This fixes hangs on the
	284X and any other aic7770 installation where level
	interrupts are not available.

aic7xxx_pci.c:
	Move the powerstate manipulation code into the OSM.  Several
	OSes now provide this functionality natively.

	Take another shot at using the data stored in scratch ram
	if the SCB2 signature is correct and no SEEPROM data is
	available.  In the past this failed if external SCB ram
	was configured because the memory port was locked.  We
	now release the memory port prior to testing the values
	in SCB2 and re-acquire it prior to doing termination control.

	Adjust for new 2 bit primary channel setting.

	Trust the STPWLEVEL setting on v 3.X BIOSes too.

	Configure any 785X ID in the same fashion and assume
	that any device with a rev id of 1 or higher has the
	PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
gibbs
d06bf490d3 aic7xxx.c:
Style nits.

	Make sure that our selection hardware is disabled
	as soon as possible after detecting a busfree and
	even go so far as to disable the selection hardware
	in advance of an event that will cause a busfree
	(ABORT or BUS DEVICE RESET message).  The concern
	is that the selection hardware will select a target
	for which, after processing the bus free, there
	will be no commands pending.  The sequencer idle
	loop will re-enable the selection should it still be
	necessary.

	In ahc_handle_scsiint(), clear SSTAT0 events several
	PCI transactions (most notably reads) prior to clearing
	SCSIINT.  The newer chips seem to take a bit of time to
	see the change which can make the clearing of SCSIINT
	ineffective.

	Don't bother panicing at the end of ahc_handle_scsiint().
	Getting to the final else just means we lost the race
	with clearing SCSIINT.

	In ahc_free(), handle init-level 0.  This can happen when we
	fail the attach for RAID devices.  While I'm here, also kill
	the parent dma tag.

	In ahc_match_scb(), consider initiator ccbs to be any
	that are not from the target mode group.  This fixes
	a bug where an external target reset CCB was not getting
	cleaned up by the reset code.

	Don't bother freezing a ccb in any of our "abort" routines
	when the status is set to CAM_REQ_CMP.  This can happen
	for a target reset ccb.

aic7xxx.reg:
	Reserve space for a completion queue.  This will be used
	to enhance performance in the near future.

aic7xxx.seq:
	Remove an optimization for the 7890 autoflush bug that
	turned out to allow, in rare cases, some data to get
	lost.

	Implement a simpler, faster, fix for the PCI_2_1 retry
	bug that hangs the sequencer on an SCB dma for certain chips.

	Test against SAVED_SCSIID rather than SELID during target
	reselections.  This is how we always did it in the past,
	but the code was modified while trying to work around an
	issue with the 7895.  SAVED_SCSIID takes into account
	twin channel adapters such as the 2742T, whereas SELID
	does not have the channel bit.  This caused invalid
	selection warnings and other strangeness on these cards.

aic7xxx_pci.c
	Use the correct mask for checking the generic aic7892
	entry.
2001-02-10 18:04:27 +00:00
gibbs
ceeff8ca20 Update Copyright notices for new year. (should have been in last commit). 2001-01-27 20:54:24 +00:00
gibbs
4d9966a39e ahc_eisa.c:
Initialize rid to 0.  This doesn't seem to make any difference
	(the driver doesn't care what rid it gets and no-one seems to
	check rid's value), but follows standard conventions.

	Pass in our device_t to ahc_alloc().  We now use device_T
	softc storage, so passing NULL results in a panic.

	Set the unit number in our softc so that the driver core
	can retrieve it.

ahc_pci.c:
	Set the unit number in our softc so that the driver core
	can retrieve it.

aic7770.c:
	Insert our softc into the list of softcs when initialization
	is successful.

aic7xxx.c:
	Remove a workaround for an aic7895 bug we will never trigger.

	Add additional diagnostic info to ahc_dump_card_state().

	Always panic the system if a sequencer assertion fails.

	AHC_SCB_BTT is a "flag" not a "feature".  Check the right
	field in the softc.

	Replace a hard coded number with a constant.

	Guard against looping forever in ahc_pause_and_flushwork().
	A hot eject or card failure may make the intstat register
	return 0xFF, so limit the number of interrupts we'll process.

	Correct the code in ahc_search_qinfifo() that guarantees that
	the sequencer will see an abort collision if the qinfifo is
	modified when a DMA is in progress.  We now do this fixup
	after modifying the queue.  This guarantees that the HSCB
	we place at the head of the queue is not the same as the
	old head.  Using "next hscb" (guaranteed not to be the
	same as the first SCB) before clearing the queue could free
	up the original head hscb to be used during a remove operation
	placing it again at the head of the qinfifo.

aic7xxx.h:
	Reduce the maximum number of outstanding commands to 253 from
	254.  To handle our output queue correctly on machines that only
	support 32bit stores, we must clear the array 4 bytes at a
	time.  To avoid colliding with a DMA write from the sequencer,
	we must be sure that 4 slots are empty when we write to clear
	the queue.  This reduces us to 253 SCBs: 1 that just completed
	and the known three additional empty slots in the queue that
	preceed it.  Yahoo was able to force this race on one of their
	systems.  Interrupts were disabled for such a time that the
	entire output queue was filled (254 entries complete without
	any processing), and our 32bit write to clear the status clobbered
	one entry.

	Add a feature tag for devices that are removable.

aic7xxx.reg:
	Never use the sequencer interrupt value of 0xF0.  We need
	to guanrantee that an INTSTAT value of 0xFF can only occur
	during card failure or a hot-eject.

	Align the busy targets table with the begining of scratch
	space.  This seems to appease a chip bug in the aic7895.

aic7xxx.seq:
	Be sure to disable select-out after a bus free event that occurs
	early in a selection.  If we don't disable select-out, we will
	believe that it is enabled even though a new selection will never
	occur.

	Move the clearing of SELDI to just before a jump.  This appeases
	another chip bug of the aic7895.

	Make the target mode command loop a bit more efficient.

	AHC_SCB_BTT is a "flag" not a "feature".  Check the right
	field in the softc.

	Properly cleanup the last SCB we tested against should we
	fail to properly find an SCB for a reselection.

	Add some additional sequencer debugging code.

aic7xxx_freebsd.c:
	Limit the driver to 253 outstanding commands per adapter.

	Guard against overflow in timeout handling.

aic7xxx_inline.h:
	AHC_SCB_BTT is a "flag" not a "feature".  Check the right
	field in the softc.

aic7xxx_pci.c:
	Set the removable feature for the apa1480 cardbus and the 29160C
	Compact PCI card.

	Don't report high byte termination information for narrow cards.

	Use a PCI read rather than a questionable delay when fetching/setting
	termination settings.
2001-01-22 21:03:48 +00:00
gibbs
a26f9d3576 Sync Perforce IDs, add tranceiver state change support, and correct
numerous error recovery buglets.

Many thanks to Tor Egge for his assistance in diagnosing problems with
the error recovery code.

aic7xxx.c:
	Report missed bus free events using their own sequencer interrupt
	code to avoid confusion with other "bad phase" interrupts.

	Remove a delay used in debugging.  This delay could only be hit
	in certain, very extreme, error recovery scenarios.

	Handle transceiver state changes correctly.  You can now
	plug an SE device into a hot-plug LVD bus without hanging
	the controller.

	When stepping through a critical section, panic if we step
	more than a reasonable number of times.

	After a bus reset, disable bus reset interupts until we either
	our first attempt to (re)select another device, or another device
	attemps to select us.  This removes the need to busy wait in
	kernel for the scsi reset line to fall yet still ensures we
	see any reset events that impact the state of either our initiator
	or target roles.  Before this change, we had the potential of
	servicing a "storm" of reset interrupts if the reset line was
	held for a significant amount of time.

	Indicate the current sequencer address whenever we dump the
	card's state.

aic7xxx.reg:
	Transceiver state change register definitions.

	Add the missed bussfree sequencer interrupt code.

	Re-enable the scsi reset interrupt if it has been
	disabled before every attempt to (re)select a device
	and when we have been selected as a target.

	When being (re)selected, check to see if the selection
	dissappeared just after we enabled our bus free interrupt.
	If the bus has gone free again, go back to the idle loop
	and wait for another selection.

	Note two locations where we should change our behavior
	if ATN is still raised.  If ATN is raised during the
	presentation of a command complete or disconnect message,
	we should ignore the message and expect the target to put
	us in msgout phase.  We don't currently do this as it
	requires some code re-arrangement so that critical sections
	can be properly placed around our handling of these two
	events.  Otherwise, we cannot guarantee that the check of
	ATN is atomic relative to our acking of the message in
	byte (the kernel could assert ATN).

	Only set the IDENTIFY_SEEN flag after we have settled
	on the SCB for this transaction.  The kernel looks at
	this flag before assuming that SCB_TAG is valid.  This
	avoids confusion during certain types of error recovery.

	Add a critical section around findSCB.  We cannot allow
	the kernel to remove an entry from the disconnected
	list while we are traversing it.  Ditto for get_free_or_disc_scb.

aic7xxx_freebsd.c:
	Only assume that SCB_TAG is accurate if IDENTIFY_SEEN is
	set in SEQ_FLAGS.

	Fix a typo that caused us to execute some code for the
	non-SCB paging case when paging SCBs.  This only occurred
	during error recovery.
2000-11-10 20:13:41 +00:00
gibbs
13459a7344 aic7xxx.c:
When restarting the sequencer, ensure that the SCBCNT register
	is 0.  A non-zero count will prevent the setting of the CCSCBDIR
	bit in any future dma operations.  The only time CCSCBCNT would
	be non-zero is if we happened to halt the dma during a reset,
	but even that should never happen.  Better safe than sorry.

	When a command completes before the target responds to an
	ATN for a recovery command, we now notify the kernel so that
	any recovery operation requeued in the qinfifo can be removed
	safely.  In the past, we did this in ahc_done(), but ahc_done()
	may be called without the card paused.  This also avoids a
	recursive call to ahc_search_qinifo() which could have occurred if
	ahc_search_qinififo() happened to be the routine to complete
	a recovery action.

	Fix 8bit math used for adjusting the qinfifo.  The index must
	be wrapped properly within the 256 entry array.  We rely on the
	fact that qinfifonext is a uint8_t in most cases to handle
	this wrap, but we missed a few spots where the resultant
	calculation was promoted to an int.

	Change the way that we deal with aborting the first or second
	entry from the qinfifo.  We now swap the first entry in the
	qinfifo with the "next queued scb" to force the sequencer
	to see an abort collision if we ever touch the qinififo while
	the sequencer is mid SCB dma.

aic7xxx.reg:
	Add new MKMSG_FAILED sequencer interrupt.  This displaced
	the BOGUS_TAG interrupt used in some previous sequencer code
	debugging.

aic7xxx.seq:
	Increment our position in the qinfifo only once the dma
	is complete and we have verified that the queue has not
	been changed during our DMA.  This simplifies code in the
	kernel.

	Protect against "instruction creep" when issuing a pausing
	sequencer interrupt.  On at least the 7890/91/96/97, the
	sequencer will coast after issuing the interrupt for up
	to two instructions.  In the past we delt with this by
	using carefully placed nops.  Now we call a routine to
	issue the interrupt followed by a nop and a ret.

	Tell the kernel should an SCB complete with the MK_MESSAGE
	flag still set.  This means the target ignored our ATN request.

	Clear the channel twice as we exit the data phase.  On the
	aic7890/91, the S/G preload logic may require the second
	clearing to get the last S/G out of the FIFO.

aic7xxx_freebsd.c:
	Don't bother searching the qinfifo for a doubly queued
	recovery scb in ahc_done.  This case is handled by the
	core driver now.

	Free the path used to issue async callbacks after the callback
	is complete.

aic7xxx_inline.h:
	Split the SCB queue routine into a routine that swaps
	the SCB with the "next queued SCB" and a routine that
	calls the swapping routine and notifies the card of
	the new SCB.  The swapping routine is now also used by
	ahc_search_qinfifo.
2000-11-06 20:05:38 +00:00
gibbs
d90f7ca9c7 aic7xxx.c:
Filter incoming transfer negotiation requests to ensure they
	never exceed the settings specified by the user.

	In restart sequencer attempt to deal with a bug in the aic7895.
	If a third party reset occurs at just the right time, the
	stack register can lock up.  When restarting the sequencer
	after handling the SCSI reset, poke SEQADDR1 before resting
	the sequencers program counter.

	When something strange happens, dump the card's transaction
	state via ahc_dump_card_state().  This should aid in debugging.

	Handle request sense transactions via the QINFIFO instead of
	attaching them to the waiting queue directly.  The waiting
	queue consumes card SCB resources and, in the pathological case
	of every target on the bus beating our selection attemps and
	issuing a check condition, could have caused us to run out
	of SCBs.  I have never seen this happen, and only early
	cards with 3 or 4 SCBs had any real chance of ever getting
	into this state.

	Add additional sequencer interrupt codes to support firmware
	diagnostics.  The diagnostic code is enabled with the
	AHC_DEBUG_SEQUENCER kernel option.

	Make it possible to switch into and out of target mode on
	the fly.  The card comes up by default as an initiator but
	will switch into target mode as soon as an enable lun operation
	is performed.  As always, target mode behavior is gated
	by the AHC_TMODE_ENABLE kernel option so most users will
	not be affected by this change.

	In ahc_update_target_msg_request(), also issue a new
	request if the ppr_options have changed.

	Never issue a PPR as a target.  It is forbidden by the spec.

	Correct a bug in ahc_parse_msg() that prevented us from
	responding to PPR messages as a target.

	Mark SCBs that are on the untagged queue with a flag instead
	of checking several fields in the SCB to see if the SCB should
	be on the queue.  This makes it easier for things like automatic
	request sense requests to be queued without touching the
	untagged queues even though they are untagged requests.

	When dealing with ignore wide residue messages that occur
	in the middle of a transfer, reset HADDR, not SHADDR for
	non-ultra2 chips.  Although SHADDR is where the firmware
	fetches the ending transfer address for a save data pointers
	request, it is readonly. Setting HADDR has the side effect
	of also updating SHADDR.

	Cleanup the output of ahc_dump_card_state() by nulling out the
	free scb list in the non-paging case.  The free list is only
	used if we must page SCBs.

	Correct the transmission of cdbs > 12 bytes in length.  When
	swapping HSCBs prior to notifing the sequencer of the new
	transaction, the bus address pointer for the cdb must also
	be recalculated to reflect its new location.  We now defer
	the calculation of the cdb address until just before queing
	it to the card.

	When pulling transfer negotiation settings out of scratch
	ram, convert 5MHz/clock doubled settings to 10MHz.

	Add a new function ahc_qinfifo_requeue_tail() for use by
	error recovery actions and auto-request sense operations.
	These operations always occur when the sequencer is paused,
	so we can avoid the extra expense incurred in the normal
	SCB queue method.

	Use the BMOV instruction for all single byte moves on
	controllers that support it.  The bmov instruction is
	twice as fast as an AND with an immediate of 0xFF as
	is used on older controllers.

	Correct a few bugs in ahc_dump_card_state().  If we have
	hardware assisted queue registers, use them to get the
	sequencer's idea of the head of the queue.  When enumerating
	the untagged queue, it helps to use the correct index for
	the queue.

aic7xxx.h:

	Indicate via a feature flag, which controllers can take
	on both the target and the initiator role at the same time.

	Add the AHC_SEQUENCER_DEBUG flag.

	Add the SCB_CDB32_PTR flag used for dealing with cdbs
	with lengths between 13 and 32 bytes.

	Add new prototypes.

aic7xxx.reg:
	Allow the SCSIBUSL register to be written to.  This is
	required to fix a selection timeout problem on the 7892/99.

	Cleanup the sequencer interrupt codes so that all debugging
	codes are grouped at the end of the list.

	Correct the definition of the ULTRA_ENB and DISC_DSB locations
	in scratch ram.  This prevented the driver from properly honoring
	these settings when no serial eeprom was available.

	Remove an unused sequencer flag.

aic7xxx.seq:
	Just before a potential select-out, clear the SCSIBUSL
	register.  Occasionally, during a selection timeout, the
	contents of the register may be presented on the bus,
	causing much confusion.

	Add sequencer diagnostic code to detect software and or
	hardware bugs.  The code attempts to verify most list
	operations so any corruption is caught before it occurs.
	We also track information about why a particular reconnection
	request was rejected.

	Don't clobber the digital REQ/ACK filter setting in SXFRCTL0
	when clearing the channel.

	Fix a target mode bug that would cause us to return busy
	status instead of queue full in respnse to a tagged transaction.

	Cleanup the overrun case.  It turns out that by simply
	butting the chip in bitbucket mode, it will ack any
	bytes until the phase changes.  This drasticaly simplifies
	things.

	Prior to leaving the data phase, make sure that the S/G
	preload queue is empty.

	Remove code to place a request sense request on the waiting
	queue.  This is all handled by the kernel now.

	Change the semantics of "findSCB".  In the past, findSCB
	ensured that a freshly paged in SCB appeared on the disconnected
	list.  The problem with this is that there is no guarantee that
	the paged in SCB is for a disconnected transation.  We now
	defer any list manipulation to the caller who usually discards
	the SCB via the free list.

	Inline some busy target table operations.

	Add a critical section to protect adding an SCB to
	the disconnected list.

aic7xxx_freebsd.c:
	Handle changes in the transfer negotiation setting API
	to filter incoming requests.  No filtering is necessary
	for "goal" requests from the XPT.

	Set the SCB_CDB32_PTR flag when queing a transaction with
	a large cdb.

	In ahc_timeout, only take action if the active SCB is
	the timedout SCB.  This deals with the case of two
	transactions to the same device with different timeout
	values.

	Use ahc_qinfifo_requeu_tail() instead of home grown
	version.

aic7xxx_inline.h:
	Honor SCB_CDB32_PTR when queuing a new request.

aic7xxx_pci.c:
	Use the maximum data fifo threshold for all chips.
2000-10-31 18:43:29 +00:00
gibbs
53b245ea4d Convert the driver to use a single DMA for fetching new commands instead
of two (one to access the circular input fifo, the other to get the SCB).
This costs us a command slot so the driver can now only queue 254
simultaneous commands.

Have the kernel driver honor critical sections in sequencer code.

When prefetching S/G segments only pull a cacheline's worth but
never less than two elements.  This reduces the impact of the
prefetch on the main data transfer when compared to the 128
byte fetches the driver used to do.

Add "bootverbose" logging for transfer negotiations.

Correct a bug in ahc_set_syncrate() that would prevent an update
of the sync parameters if only the ppr_options had changed.

Correct locking for calls to ahc_free_scb().  ahc_free_scb() is no
longer protected internally to simplify ports to other platforms.

Make sure we unfreeze our SIMQ if a resource shortage has occurred
and an SCB is been freed.

ahc_pci.c:
	Turn on cacheline streaming for all controllers that support it.

	Clarify diagnostic messages about PCI interrupts.
2000-10-05 04:24:14 +00:00
gibbs
872c96a9d4 Add Perforce RCSIDs for easy revision correlation to my local tree.
ahc_pci.c:
	Bring back the AHC_ALLOW_MEMIO option at least until the
	memory mapped I/O problem on the SuperMicro 370DR3 is
	better understood.

aic7xxx.c:
	If we see a spurious SCSI interrupt, attempt to clear it and
	continue by unpausing the sequencer.

	Change the interface to ahc_send_async().  Some async messages
	need to be broadcast to all the luns of a target or all the
	targets of a bus.  This is easier to achieve by passing explicit
	channel, target, and lun parameters instead of attempting to
	construct a device info struct to match.

	Filter the sync parameters for the PPR message in exactly the
	same way we do for an old fashioned SDTR message.

	Correct some typos and correct a panic message.

	Handle rejected PPR messages.

	In ahc_handle_msg_reject(), let ahc_build_transfer_msg() build
	any additional transfer messages instead of doing this inline.

aic7xxx.h:
	Increase the size of both msgout_buf and msgin_buf to
	better accomodate PPR messages.

aic7xxx_freebsd.c:
	Update for change in ahc_send_async() parameters.

aic7xxx_freebsd.h
	Update for change in ahc_send_async() parameters.

	Honor AHC_ALLOW_MEMIO.

aic7xxx_pci.c:
	Check the error register before going into full blown PCI
	interrupt handling.  This avoids a few costly PCI configuration
	space reads when we run our PCI interrupt handler because another
	device sharing our interrupt line is more active than we are.

	Also unpause the sequencer after processing a PCI interrupt.
2000-09-22 22:18:05 +00:00
gibbs
8a948fec9d Today is just not my day. Really get the right file. 2000-09-16 21:55:31 +00:00
gibbs
39399239a0 Pull the correct file over to freefall. 2000-09-16 20:59:12 +00:00
gibbs
7691c1f500 Move aicasm to its own subdirectory.
Separate our platform independent hooks from core driver functionality
shared between platforms (FreeBSD and Linux at this time).

Add sequencer workarounds for several chip->chipset interactions.

Correct external SCB corruption problem on aic7895 based cards (3940AUW).

Lots of cleanups resulting from the port to another OS.
2000-09-16 20:02:28 +00:00
gibbs
3255f4fca4 ahc_pci.c:
Disable "cache line streaming" for aic7890/91 Rev A chips.  I
	have never seen these chips fail using this feature, but
	some of Adaptec's regression tests have.

	Explicitly set "cache line streaming" to on for aic7896/97
	chips.  This was happening before, but this documents the
	fact that these chips will not function correctly without
	CACHETHEEN set.

aic7xxx.h:
	Add new bug types.

	Fix a typo in a comment.

aic7xxx.reg:
	Add a definition for the SHVALID bit in SSTAT3 for Ultra2/3
	chips.  This bit inicates whether the bottom most (current)
	element in the S/G fifo has exhausted its data count.

aic7xxx.seq:
	Be more careful in how we turn off the secondary DMA channel.
	Being less careful may hang the PCI bus arbitor that negotiates
	between the two DMA engines.

	Remove an unecessary and incorrect flag set operation in
	the overrun case.

	On Ultra2/3 controllers, clear the dma FIFO before starting
	to handle an overrun.  We don't want any residual bytes from
	the beginning of the overrun to cause the code that shuts
	down the DMA engine from hanging because the FIFO is not
	(and never will be) empty.

	If the data fifo is empty by the time we notice that a
	read transaction has completed, there is no need to
	hit the flush bit on aic7890/91 hardware that will not
	perform an auto-flush.  Skip some cycles by short circuiting
	the manual flush code in this case.

	When transitioning out of data phase, make sure that we
	have the next S/G element loaded for the following
	reconnect if there is more work to do.  The code
	would do this in most cases before, but there was
	a small window where the current S/G element could
	be exhausted before our fetch of the next S/G element
	completed.  Since the S/G fetch is already initiated
	at this point, it makes sense to just wait for the
	segment to arrive instead of incuring even more latency
	by canceling the fetch and initiating it later.

	Fast path the end of data phase handling for the last
	S/G segment.   In the general case, we might have
	worked ahead a bit by stuffing the S/G FIFO with
	additional segments.  If we stop before using them
	all, we need to fixup our location in the S/G stream.
	Since we can't work past the last S/G segment, no
	fixups are ever required if we stop somewhere in
	that final segment.

	Fix a little buglet in the target mode dma bug handler.
	We were employing the workaround in all cases instead
	of only for the chips that require it.

	Fix the cause of SCB timeouts and possible "lost data"
	during read operations on the aic7890.  When sending
	a data on any Ultra2/3 controller, the final segment
	must be marked as such so the FIFO will be flushed and
	cleaned up correctly when the transfer is ended.  We
	failed to do this for the CDB transfer and so, if
	the target immediately transfered from command to data
	phase without an intervening disconnection, the first
	segment transferred would be any residual bytes from
	the cdb transfer.  The Ultra160 controllers for some
	reason were not affected by this problem.

Many Thanks to Tor Egge for bringing the aic7890 problem
to my attention, providing analysis, as well as a mechanism
to reproduce the problem.
2000-07-27 23:17:52 +00:00
gibbs
3c297571e4 o Convert to <inttypes.h> style fixed sized types to facilitate porting to
other systems.

 o Normalize copyright text.

 o Clean up probe code function interfaces by passing around a single
   structure of common arguments instead of passing "too many" args
   in each function call.

 o Add support for the AAA-131 as a SCSI adapter.

 o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net

 o Correct manual termination support for PCI cards.  The bit definitions
   for manual termination control in the SEEPROM were incorrect.

 o Add support for extracting NVRAM information from SCB 2 for BIOSen
   that use this mechanism to pass this data to OS drivers.

 o Properly set the STPWLEVEL bit in PCI config space based on the
   setting in an SEEPROM.

 o Go back to useing 32byte SCBs for all controllers.  The current
   firmware allows us to embed 12byte cdbs on all controllers in
   a 32byte SCB, and larger cdbs are rarely used, so it is a
   better use of this space to offer more SCBs (32).

 o Add support for U160 transfers.

 o Add an idle loop executed during data transfers that prefetches
   S/G segments on controllers that have a secondary DMA engine
   (aic789X).

 o Improve the performance of reselections by avoiding an extra
   one byte DMA in the case of an SCB lookup miss for the reselecting
   target.  We now keep a 16byte "untagged target" array on the card
   for dealing with untagged reselections.  If the controller has
   external SCB ram and can support 64byte SCBs, then we use an
   "untagged target/lun" array to maximize concurrency.  Without
   external SCB ram, the controller is limited to one untagged
   transaction per target, auto-request sense operations excluded.

 o Correct the setup of the STPWEN bit in SXFRCTL1.  This control
   line is tri-stated until set to one, so set it to one and then
   set it to the desired value.

 o Add tagged queuing support to our target role implementation.

 o Handle the common cases of the ignore wide residue message
   in firmware.

 o Add preliminary support for 39bit addressing.

 o Add support for assembling on big-endian machines.  Big-endian
   support is not complete in the driver.

 o Correctly remove SCBs in the waiting for selection queue when
   freezing a device queue.

 o Now that we understand more about the autoflush bug on the
   aic7890, only use the workaround on devices that need it.

 o Add a workaround for the "aic7890 hangs the system when you
   attempt to pause it" problem.  We can now pause the aic7890
   safely regardless of what instruction it is executing.
2000-07-18 20:12:14 +00:00
gibbs
db6a3ed930 o Correct the offsets into the syncrate table for paritcular
negotiation features (DT, ULTRA2, ULTRA, FAST).  The offsets
  where not properly updated when the DT entry was added and so
  the driver could attempt to negotiate a speed faster than that
  supported by the target device or even requested by the user
  via SCSI-Select settings. *

o Update the target mode incoming command queue kernel index value
  ever 128 commands instead of 32.  This means that the kernel will
  always try to keep its index (as seen on the card - the kernel may
  actually have cleared more space) 128 commands ahead of where the
  sequencer is adding entries.

o Use the HS_MAILBOX register instead of the KERNEL_TQINPOS location
  in SRAM to indicate the kernel's target queue possition on Ultra2
  cards.  This avoids the "pause bug" on these cards and also turns
  out to be much more efficient.

o When enabling or disabling a particular target id for target mode,
  make sure that the taret id in the SCSIID register does not
  reference an ID that is not to receive target selections.  This
  is only an issue on chips that support the multiple target id
  feature where the value in SCSIID will still affect selection
  behavior regardless of the values in the target id bit field
  registers.

o Remove some target mode debugging printfs.

o Make sure that the sense length reported in ATIO commands is
  always zero.  This driver does not, yet, report HBA generated
  sense information for accepted commands.

o Honor the CAM_TIME_INFINITY and CAM_TIME_DEFAULT values for
  the CCB timeout field.

o Make the driver compile with AHC_DEBUG again.

* Noticed by: Andrew Gallatin<gallatin@cs.duke.edu>
2000-03-18 22:28:20 +00:00
gibbs
c8e218c397 Kill the "unpause_always" argument to unpause_sequencer(). The reasons
for optimizing the unpause operation no-longer exist, and this is much
safer.

When restarting the sequencer, reconstitute the free SCB list on the card.
This deals with a single instruction gap between marking the SCB as free
and actually getting it onto the free list.

Reduce the number of transfer negotiations that occur.  In the past, we
renegotiated after every reported check condition status.  This ensures
that we catch devices that have unexpectidly reset.  In this situation,
the target will always report the check condition before performing a
data-phase.  The new behavior is to renegotiate for any check-condition where
the residual matches the orginal data-length of the command (including
0 length transffers).  This avoids renegotiations during things like
variable tape block reads, where the check condition is reported only
to indicate the residual of the read.

Revamp the parity error detection logic.  We now properly report and
handle injected parity errors in all phases.  The old code used to hang
on message-in parity errors.

Correct the reporting of selection timeout errors to the XPT.  When
a selection timeout occurs, only the currently selecting command
is flagged with SELTO status instead of aborting all currently active
commands to that target.

Fix flipped arguments in ahc_match_scb and in some of the callers of this
routine.  I wish that gcc allowed you to request warnings for enums passed
as ints.

Make ahc_find_msg generically handle all message types.

Work around the target mode data-in wideodd bug in all non-U2 chips.
We can now do sync-wide target mode transfers in target mode across the
hole product line.

Use lastphase exclusively for handling timeouts.  The current phase
doesn't take the bus free state into account.

Fix a bug in the timeout handler that could cause corruption of the
disconnected list.

When sending an embedded cdb to a target, ensure that we start on a
quad word boundary in the data-fifo.  It seems that unaligned stores
do not work correctly.
2000-02-09 21:25:00 +00:00
gibbs
ee07555354 Update copyrights to Y2K.
93cx6.c:
	Make the SRAM dump output a little prettier.

aic7xxx.c:
	Store all SG entries into our SG array in kernel space.
	This makes data-overrun and other error reporting more
	useful as we can dump all SG entries.  In the past,
	we only stored the SG entries that the sequencer might
	need to access, which meant we skipped the first element
	that is embedded into the SCB.

	Add a table of chip strings and replace ugly switch
	statements with table lookups.

	Add a table with bus phase strings and message reponses
	to parity errors in those phases.  Use the table to
	pretty print bus phase messages as well as collapse
	another switch statement.

	Fix a bug in target mode that could cause us to unpause
	the sequencer early in bus reset processing.

	Add the 80MHz/DT mode into our syncrate table.  This
	rate is not yet used or enabled.

	Correct some comments, clean up some code...

aic7xxx.h:
	Add U160 controller feature information.

	Add some more bit fields for various SEEPROM formats.

aic7xxx.reg:
	Add U160 register and register bit definitions.

aic7xxx.seq:
	Make phasemis state tracking more straight forward.  This
	avoids the consumption of SINDEX which is a very useful register.

	For the U160 chips, you must use the 'mov' instruction to
	update DFCNTRL.  Using 'or' to set the PRELOADED bit is
	completely ineffective.

	At the end of the command phase, wair for our ACK signal
	to de-assert before disabling the SCSI dma engine.  For
	slow devices, this avoids clearing the ACK before the
	other end has had a chance to see it and lower REQ.
2000-01-07 23:08:20 +00:00
gibbs
09d56a3f8f Simplify my copyright license terms.
aic7xxx.c:
	Add a function for sucking firmware out of the controller
	prior to reset.

	Remove some inline bloat from functions that should not have
	been inlined.

	During initialization, wait 1ms after the chip reset before
	touching any registers.  You can get machine checks on certain
	architectures (Atari I think?) without the delay.

	Return CAM_REQ_CMP for external BDR requests instead
	of CAM_BDR_SENT.

	Bump some messages to bootverbose levels above 1.

	Don't clear any negotiated sync rate if the target rejects
	a WDTR message.  The sync rate is only cleared if the target
	accepts a WDTR message.

	Fix a small bug in the mesgin handling code that could cause
	us to believe that we had recieved a message that was actually
	received by another target.  This could only confuse us in
	some very rare transmission negotiation scenarios.

	Remove some unecessary cleanup of residual information after
	a residual is reported.  The sequencer does this when the
	command is queued now.
1999-12-06 18:23:31 +00:00
peter
3b842d34e8 $Id$ -> $FreeBSD$ 1999-08-28 01:08:13 +00:00
gibbs
0720a2d2af Kill an unused INTSTAT type. 1999-08-16 22:43:08 +00:00
gibbs
be407614c4 Better workaround for aic7890 chip bug. Use the HS_MAILBOX register to
tell the sequencer to pause itself for a target msg variable update.  This
avoids the pause race entirely as HS_MAILBOX can be accessed without
pausing the chip.

3.2 Merge candidate.
1999-05-14 05:07:25 +00:00
gibbs
8674f2244c Clean up and order register definitions. 1999-03-08 22:43:23 +00:00
gibbs
399fca227c Keep track of negotiated transfer parameters for each initiator<->target
connection.

Clean up support for devices featuring the multiple target SCSI ID feature.
On aic7890/91/96/97 chips, we can now assume the target role on multiple
target ids simultaneously.  Although these chips also have sufficient
instruction space to hold to support the initiator and target role at the
same time, the initiator role is currently disabled as it will conflict
(chip design restriction) with the multi-tid feature.  I'll probably add
a nob to enable the initiator (there-by disabling multi-tid) some time
in the future.

Return queue full or busy, depending on the tagged nature of the incoming
request, if our command input queue fills up in host memeory.

Deal with accept target I/O resource shortages.

If we get an underrun on a transaction that wasn't supposed to transmit
any data, don't attempt to print out the S/G list.  The code would
run until hitting a non-present page. (oops)
1999-03-05 23:35:48 +00:00
gibbs
b0bf7fe0ff Add support for routing initiator transactions to disabled luns to the
black hole device.  The controller will now only accept selections if
the black hole device is present and some other target/lun is enabled
for target mode.

Handle the IGNORE WIDE RESIDUE message.  This support has not been tested.

Checkpoint work on handling ABORT, BUS DEVICE RESET, TERMINATE I/O PROCESS,
and CLEAR QUEUE messages as a target.

Fix a few problems with tagged command handling in target mode.

Wait until the sync offset counter falls to 0 before changing phase
after a data-in transfer completes as the DMA logic seems to indicate
transfer complete as soon as our last REQ is issued.

Simplify some of the target mode message handling code in the sequencer.
1999-01-14 06:14:15 +00:00
gibbs
dc4a57e23b Fix a few problems with handling rejected transfer negotiation messages.
Use the host message loop for any unknown message types instead of performing
a reject message in the sequencer.  Pass reject messages to the host
message loop too which frees up a sequencer interrupt type slot.

Default to issuing a bus reset if initiator mode is enabled.  It seems
that the reset scsi bus bit is not defined in the same location for
all aic78xx BIOSes, so attempting to honor this setting will have to
wait until I get more information on how to detect it.

Nuke some unused variables.
1998-12-17 00:06:52 +00:00
gibbs
4bb599f96c Perform a save data pointers operation if a data transfer was performed
in target mode, but we are not completing the command.

Use a template of allowed bus arbitration phases to selectively and
dynamically enable/disable initiator or target (re)selection.

Properly handle timeouts for target role transactions - just go to the
bus free state and report the error to the peripheral driver.

Checkpoint support for the XPT_ABORT_CCB function code.  This currently
handles the accept tio and immediate notify ccb types, but does not
handle the continue target I/O or SCSI I/O ccb types.  This is enough
to handle dynamic target enable/disable events.

Clean up the SCSI reset code so that we perform at most 1 SCSI bus
reset at initialization, the reset requested by the XPT layer.
1998-12-15 08:22:42 +00:00
gibbs
3e9f8a5d64 Revamp the way that exceptional message handling is performed so that it
is more robust and common code can be used for both the target and iniator
roles.  The mechanism for tracking negotiation state has also been simplified.

Add support for sync/wide negotiation in target mode and fix many of
the target mode bugs running at higher speeds uncovered.  Make a first
stab at getting all of the bus skew delays correct.  Sync+Wide dataout
transfers still cause problems, but this may be an initiator problem.

Ensure that we exit BITBUCKET mode if the controller is restarted.

Add support for target mode only firmware downloads.  This has been
tested on the aic7880, but should mean that we can perform target mode
on any aic7xxx controller.  Mixed mode (initiator and target roles in
the same firmware load) is currently only supported on the aic7890, but
with optimization, may fit on chips with less instruction space.
1998-12-10 04:14:50 +00:00
gibbs
ad7080d581 Change the delivery mechanism for incoming target commands. We now
use a 256 entry ring buffer of descriptersfor this purpose.  This allows
the use of a simple 8bit counter in the sequencer code for tracking start
location.

Entries in the ring buffer now contain a "cmd_valid" byte at their tail.
As an entry is serviced, this byte is cleared by the kernel and set by
the sequencer during its dma of a new entry.  Since this byte is the last
portion of the command touched during a dma, the kernel can use this
byte to ensure the command it processes is completely valid.

The new command format requires a fixed sized DMA from the controller
to deliver which allowed for additional simplification of the sequencer
code.  The hack that required 1 SCB slot to be stolen for incoming
command delivery notification is also gone.
1998-11-23 01:33:47 +00:00
gibbs
b845ffee80 Massive overhaul of the aic7xxx driver:
- Convert to CAM
 - Use a new DMA based queuing and paging scheme
 - Add preliminary target mode support
 - Add support for the aic789X chips
 - Take advantage of external SRAM on more controllers.
 - Numerous bug fixes and performance improvements.
1998-09-15 07:24:17 +00:00
gibbs
b9404180a2 Add support to aicasm for "downloaded constants". These are immediate
operands that are set during seqeuncer program download instead of at
assembly time.

Convert the sequencer code to use" downloaded constants" for four run time
constants that vary depending on the board type.  This frees up 4 bytes
of sequencer scratch ram space where these constants used to be stored and
also removes the additional instructions required to load their values
into the accumulator prior to using them.

Remove the REJBYTE sram variable.  The host driver can just as easly
read the accumulator to get this value.

The scratch ram savings is important as the old code used to clober the
SCSICONF register on 274X cards which sits near the top of scratch ram
space.  The SCSICONF register controls bus termination, and clobbering
it is not a good thing.  Now we have 4 bytes to spare.

This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.

Doug Ledford determined the cause of the problem, fixes by me.
1997-09-27 19:37:31 +00:00
gibbs
6bb904da80 Add a spin lock that prevents the sequencer from attempting to add an
entry to the QOUTFIFO when it is full.  This should eliminate the
"Timed out while idle" problems that many have reported.

In truth, this is somewhat of a hack.  Although are interrupt latency is
low enough that we should be able to always service the queue in time,
since each entry must be passed up to the higher SCSI layer for what can
be a large amount of processing (perhaps even resulting in a new command
being queued) with interrupts disabled, we need this mechanism to avoid
overflow.  In the future, these additional tasks will be offloaded to a
software interrupt handler which should make this hack unnecessary.
1997-08-13 17:02:47 +00:00
gibbs
7ebb73022c Modify my copyright notice to allow the sequencer to be used with GPLed
software (aka Linux).

Fix a few bugs in the sequencer assembler.

Make it easy to compiler the assembler with debugging turned on.
1997-06-27 19:38:56 +00:00
gibbs
3ca5733308 The following scenario would result in a bogus residual being reported
if SCB Paging was enabled:

    disconnect with more data to transfer
    disconnected SCB gets paged out
    target reconnects so we page SCB back in
    target completes transfer so residual is 0
    target disconnects
    SCB gets reused but not paged out since the residual is 0 (optimization)
    target reconnects so we page the SCB back in
    we report a residual because of stale residual information.

The fix for this is to set a flag that forces the SCB to be paged back
up to the host if we page in an SCB with a residual

Pointed out by: Doug Ledford <dledford@dialnet.net>
1997-04-24 16:52:18 +00:00
gibbs
5b06a03240 Re-arange the selection and reselection code to hopefully kill the
spurious selection timeouts that have been reported.
1997-04-14 02:26:59 +00:00
gibbs
40f591dab8 Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c:
New sequencer assembler for the aic7xxx adapters.  This assembler
	performs some amount of register type checking, allows bit
	manipulation of symbolic constants, and generates "patch tables"
	for conditionalized downloading of portions of the program.
	This makes it easier to take full advantage of the different
	features of the aic7xxx cards without imposing run time penalies
	or being bound to the small memory footprints of the low end
	cards for features like target mode.

aic7xxx.reg:
	New, assembler parsed, register definitions fo the aic7xxx cards.
	This was done primarily in anticipation of 7810 support which
	will have a different register layout, but should be able to use
	the same assembler.  The kernel aic7xxx driver consumes a generated
	file in the compile directory to get the definitions of the register
	locations.

aic7xxx.seq:
	Convert to the slighly different syntax of the new assembler.

	Conditionalize SCB_PAGING, ultra, and twin features which shaves
	quite a bit of space once the program is downloaded.

	Add code to leave the selection hardware enabled during reconnects
	that win bus arbitration.  This ensures that we will rearbitrate
	as soon as the bus goes free instead of delaying for a bit.

	When we expect the bus to go free, perform all of the cleanup
	associated with that event "up front" and enter a loop awaiting
	bus free.  If we see a REQ first, complain, but attempt to
	continue.  This will hopefully address, or at least help diagnose,
	the "target didn't send identify" messages that have been reported.

Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00