on UltraSPARC workstations. The driver is based on OpenBSD's SBus
cs4231 driver and heavily modified to incorporate into sound(4)
infrastructure. Due to the lack of APCDMA documentation, the DMA
code of SBus cs4231 came from OpenBSD's driver.
The driver runs without Giant lock and supports both SBus and EBus
based CS4231 audio controller. Special thanks to marius for providing
feedbacks during the driver writing. His feedback made it possible
to write hiccup free playback code under high system loads.
Approved by: jake (mentor)
Reviewed by: marius (initial version)
Tested by: marius, kwm, Julian C. Dunn(jdunn AT opentrend DOT net)
of protocols. The call to divert_packet() is done through a function pointer. All
semantics of IPDIVERT remain intact. If IPDIVERT is not loaded ipfw will refuse to
install divert rules and natd will complain about 'protocol not supported'. Once
it is loaded both will work and accept rules and open the divert socket. The module
can only be unloaded if no divert sockets are open. It does not close any divert
sockets when an unload is requested but will return EBUSY instead.
List of functional changes:
- Make a single device per single node with a single hook.
This gives us parrallelizm, which can't be achieved on a single
node with many devices/hooks. This also gives us flexibility - we
can play with a particular device node, not affecting others.
- Remove read queue as it is. Use struct ifqueue instead. This change
removes a lot of extra memcpy()ing, m_devget()ting and m_copymem()ming.
In ng_device_receivedata() we enqueue an mbuf and wake readers.
In ngdread() we take one mbuf from qeueue and uiomove() it to
userspace. If no mbuf is present we optionally block. [1]
- In ngdwrite() we create an mbuf from uio using m_uiotombuf().
This is faster then uiomove() into buffer, and then m_copydata(),
and this is much better than huge m_pullup().
- Perform locking of device
- Perform locking of connection list.
- Clear out _rcvmsg method, since it does nothing good yet.
- Implement NGM_DEVICE_GET_DEVNAME message.
- #if 0 ioctl method, while nothing is done here yet.
- Return immediately from ngdwrite() if uio_resid == 0.
List of tidyness changes:
- Introduce device2priv(), to remove cut'n'paste.
- Use MALLOC/FREE, instead of malloc/free.
- Use unit2minor().
- Use UID_ROOT/GID_WHEEL instead of 0/0.
- Define NGD_DEVICE_DEVNAME, use it.
- Use more nice macros for debugging. [2]
- Return Exxx, not -1.
style(9) changes:
- No "#endif" after short block.
- Break long lines.
- Remove extra spaces, add needed spaces.
[1] Obtained from: if_tun.c
[2] Obtained from: ng_pppoe.c
Reviewed by: marks
Approved by: julian (mentor)
MFC after: 1 month
be used to announce various system activity.
The auxio device provides auxiliary I/O functions and is found on various
SBus/EBus UltraSPARC models. At present, only front panel LED is
controlled by this driver.
Approved by: jake (mentor)
Reviewed by: joerg
Tested by: joerg
Users should move to the new geom_vinum implementation instead.
The refcount logic which is being added to devices to enable safe module
unloading and the buf/vm work also in progress would require a major rework
of the (old)-vinum code to comply with the new semantics.
The actual source files will not be removed until I have coordinated with
the geomvinum people if they need any bits repo-copied etc.
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
to RS232 bridges, such as the one found in the DeLorme Earthmate USB GPS
receiver (which is the only device currently supported by this driver).
While other USB to serial drivers in the tree rely heavily on ucom, this
one is self-contained. The reason for that is that ucom assumes that
the bridge uses bulk pipes for I/O, while the Cypress parts actually
register as human interface devices and use HID reports for configuration
and I/O.
The driver is not entirely complete: there is no support yet for flow
control, and output doesn't seem to work, though I don't know if that is
because of a bug in the code, or simply because the Earthmate is a read-
only device.
compile option. All FreeBSD packet filters now use the PFIL_HOOKS API and
thus it becomes a standard part of the network stack.
If no hooks are connected the entire packet filter hooks section and related
activities are jumped over. This removes any performance impact if no hooks
are active.
Both OpenBSD and DragonFlyBSD have integrated PFIL_HOOKS permanently as well.
and preserves the ipfw ABI. The ipfw core packet inspection and filtering
functions have not been changed, only how ipfw is invoked is different.
However there are many changes how ipfw is and its add-on's are handled:
In general ipfw is now called through the PFIL_HOOKS and most associated
magic, that was in ip_input() or ip_output() previously, is now done in
ipfw_check_[in|out]() in the ipfw PFIL handler.
IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to
be diverted is checked if it is fragmented, if yes, ip_reass() gets in for
reassembly. If not, or all fragments arrived and the packet is complete,
divert_packet is called directly. For 'tee' no reassembly attempt is made
and a copy of the packet is sent to the divert socket unmodified. The
original packet continues its way through ip_input/output().
ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet
with the new destination sockaddr_in. A check if the new destination is a
local IP address is made and the m_flags are set appropriately. ip_input()
and ip_output() have some more work to do here. For ip_input() the m_flags
are checked and a packet for us is directly sent to the 'ours' section for
further processing. Destination changes on the input path are only tagged
and the 'srcrt' flag to ip_forward() is set to disable destination checks
and ICMP replies at this stage. The tag is going to be handled on output.
ip_output() again checks for m_flags and the 'ours' tag. If found, the
packet will be dropped back to the IP netisr where it is going to be picked
up by ip_input() again and the directly sent to the 'ours' section. When
only the destination changes, the route's 'dst' is overwritten with the
new destination from the forward m_tag. Then it jumps back at the route
lookup again and skips the firewall check because it has been marked with
M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with
'option IPFIREWALL_FORWARD' to enable it.
DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for
a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will
then inject it back into ip_input/ip_output() after it has served its time.
Dummynet packets are tagged and will continue from the next rule when they
hit the ipfw PFIL handlers again after re-injection.
BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as
they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS.
More detailed changes to the code:
conf/files
Add netinet/ip_fw_pfil.c.
conf/options
Add IPFIREWALL_FORWARD option.
modules/ipfw/Makefile
Add ip_fw_pfil.c.
net/bridge.c
Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw
is still directly invoked to handle layer2 headers and packets would
get a double ipfw when run through PFIL_HOOKS as well.
netinet/ip_divert.c
Removed divert_clone() function. It is no longer used.
netinet/ip_dummynet.[ch]
Neither the route 'ro' nor the destination 'dst' need to be stored
while in dummynet transit. Structure members and associated macros
are removed.
netinet/ip_fastfwd.c
Removed all direct ipfw handling code and replace it with the new
'ipfw forward' handling code.
netinet/ip_fw.h
Removed 'ro' and 'dst' from struct ip_fw_args.
netinet/ip_fw2.c
(Re)moved some global variables and the module handling.
netinet/ip_fw_pfil.c
New file containing the ipfw PFIL handlers and module initialization.
netinet/ip_input.c
Removed all direct ipfw handling code and replace it with the new
'ipfw forward' handling code. ip_forward() does not longer require
the 'next_hop' struct sockaddr_in argument. Disable early checks
if 'srcrt' is set.
netinet/ip_output.c
Removed all direct ipfw handling code and replace it with the new
'ipfw forward' handling code.
netinet/ip_var.h
Add ip_reass() as general function. (Used from ipfw PFIL handlers
for IPDIVERT.)
netinet/raw_ip.c
Directly check if ipfw and dummynet control pointers are active.
netinet/tcp_input.c
Rework the 'ipfw forward' to local code to work with the new way of
forward tags.
netinet/tcp_sack.c
Remove include 'opt_ipfw.h' which is not needed here.
sys/mbuf.h
Remove m_claim_next() macro which was exclusively for ipfw 'forward'
and is no longer needed.
Approved by: re (scottl)
The ISA probe uses an identify routine to probe all slot locations from
1 to 14 that do not conflict with other allocated resources. This required
making aic7770.c part of the driver core when compiled as a module.
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
Use aic_scb_timer_start() consistently to start the watchdog timer.
This removes a few places that verbatum copied the code in
aic_scb_timer_start().
During recovery processing, allow commands to still be queued to
the controller. The only requirement we have is that our recovery
command be queued first - something the code already guaranteed.
The only other change required to make this work is to prevent
timers from being started for these newly queued commands.
Approved by: re
