Merge vendor bugfix for a possible deadlock related to async destroy
and improve write performance by introducing a new lock protecting
tx_open_txg.
Illumos ZFS issues:
3642 dsl_scan_active() should not issue I/O to determine if async
destroying is active
3643 txg_delay should not hold the tc_lock
MFC after: 1 week
route. What it was is there are two places in ip_output.c
where we do a goto again. One place was fine, it
copies out the new address and then resets dst = ro->rt_dst;
But the other place does *not* do that, which means earlier
when we found the gateway, we have dst pointing there
aka dst = ro->rt_gateway is done.. then we do a
goto again.. bam now we clobber the default route.
The fix is just to move the again so we are always
doing dst = &ro->rt_dst; in the again loop.
PR: 174749,157796
MFC after: 1 week
GDT from the correct segment, otherwise a triple fault would be caused.
In some virtual environments (VMware, VirtualBox, etc) this could lead
to a unhandled error or hang in the guest emulation software.
Thanks to avg and jhb for a few hints in the right direction.
Noticed by: Jeremy Chadwick <jdc@koitsu.org> (and many others)
MFC after: 1 week
instead of kernel_map size to prevent kernel memory exhaustion
by mbufs and a subsequent panic on physical page allocation
failure.
On architectures without a direct map all mbuf memory (except
for jumbo mbufs larger than PAGE_SIZE) comes from kmem_map.
It is the limiting factor hence.
For architectures with a direct map using the size of kmem_map
is a good proxy of available kernel memory as well. If it is
much smaller the mbuf limit may be sub-optimal but remains
reasonable, while avoiding panics under exhaustion.
The overall mbuf memory limit calculation may be reconsidered
again later, however due to the many different mbuf sizes and
different backing KVM maps it is a tricky subject.
Found by: pho's new network stress test
Pointed out by: alc (kmem_map instead of kernel_map)
Tested by: pho
duplicate ACK make sure we actually have new data to send.
This prevents us from sending unneccessary pure ACKs.
Reported by: Matt Miller <matt@matthewjmiller.net>
Tested by: Matt Miller <matt@matthewjmiller.net>
MFC after: 2 weeks
impossible to set quota and reservation on pools lower than version 22.
Problem has been reported and a solution discussed with vendor.
Illumos ZFS issues:
3739 cannot set zfs quota or reservation on pool version < 22
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reported by: Steve Wills <swills@FreeBSD.org>
MFC after: 3 days
Partially implement generic_bs_*_8() for MIPS platforms.
This is known to work with TARGET_ARCH=mips64 with FreeBSD/BERI.
Assuming that other definitions in cpufunc.h are correct it will
work on non-o64 ABI systems except sibyte. On sibyte and o32 systems
generic_bs_*_8() will remain panic() implementations.
Sponsored by: DARPA, AFRL
Reviewed by: imp, jmallett (older versions)
that uses non-ISA IRQs but use a plain IRQ resource in _CRS. However,
a non-ISA IRQ can't fit into a plain IRQ resource. If we encounter a
link like this, build the resource buffer from _PRS instead of _CRS.
- Set the correct size of the end tag in a resource buffer.
Tested by: Benjamin Lee <ben@b1c1l1.com>
MFC after: 2 weeks
than VLAN groups.
Some chips (eg this rtl8366rb) has a VLAN group per port - you first
define a set of VLANs in a vlan group, then you assign a VLAN group
to a port.
Other chips (eg the AR8xxx switch chips) have a VLAN ID array per
port - there's no group per se, just a list of vlans that can be
configured.
So for now, the switch API will use the latter and rely on drivers
doing the heavy lifting if one wishes to use the VLAN group method.
Maybe later on both can be supported.
PR: kern/177878
PR: kern/177873
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
the pause/resume code to not be called completely symmetrically.
I'll chase down the root cause of that soon; this at least works around
the bug and tells me when it happens.
This allows users who boot without loader to adjust their environments
around slightly buggy or slow hardware.
PR: kern/161809
Submitted by: rozhuk.im@gmail.com
MFC after: 2 weeks
is compiled in or not.
This fixes issues with people running -HEAD but who build modules
without doing a "make buildkernel KERNCONF=XXX", thus picking up
opt_*.h. The resulting module wouldn't have 11n enabled and the
chainmask configuration would just be plain wrong.
This allows mapping a tape drive in a changer (as reported by
'chio status') to a sa(4) driver instance by comparing the
serial numbers.
The designators can be ASCII (which is printed out directly), binary
(which is printed in hex format) or UTF-8, which is printed in either
native UTF-8 format if the terminal can support it, or in %XX notation
for non-ASCII characters. Thanks to Hiroki Sato <hrs@> for the
explaining UTF-8 printing and example UTF-8 printing code.
chio.h: Modify the changer_element_status structure to add new
fields and definitions from the SMC3r16 spec.
Rename the original CHIOGSTATUS ioctl to OCHIOGTATUS and
define a new CHIOGSTATUS ioctl.
Clean up some tab/space issues.
chio.c: For the 'status' subcommand, print the designator field
if it is supplied by a device.
scsi_ch.h: Add new flags for DVCID and CURDATA to the READ
ELEMENT STATUS command structure.
Add a read_element_status_device_id structure
for the data fields in the new standard. Add new
unions, dt_or_obsolete and voltage_devid, to hold
and address data from either SCSI-2 or newer devices.
scsi_ch.c: Implement support for fetching device IDs with READ
ELEMENT STATUS data.
Add new arguments to scsi_read_element_status() to
allow the user to request the DVCID and CURDATA bits.
This isn't compiled into libcam (it's only an internal
kernel interface), so we don't need any special
handling for the API change.
If the user issues the new CHIOGSTATUS ioctl, copy all of
the available element status data out. If he issues the
OCHIOGSTATUS ioctl, we don't copy the new fields in the
structure.
Fix a bug in chopen() that would result in the peripheral
never getting unheld if chgetparams() failed.
Sponsored by: Spectra Logic
Submitted by: Po-Li Soong
MFC After: 1 week
This is intended to be used as a stop-gap for switch devices
which expose multiple ethernet PHYs but we don't have a driver
for - here, etherswitchcfg and the general switch configuration
API can be used to interface to said PHYs.
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
