It is legal to have a device with device type 0x1f, that just means
that the device is of unknown type. Instead, only check the peripheral
qualifier when deciding whether or not to reject a device based on its
inquiry information.
Tested by: julian
MFC after: 3 weeks
time in the cases where it really sends the drive out to lunch, but it also
allows us to catch very wierd edge cases of strange drives that might take
a very long time (emulated disk drives over a network, e.g.).
quirk regarding the C- series makes me suspect that all Olympus models have
the same quirks, but I cannot prove it.
Submitted by: Bernd Walter <ticso@cicely8.cicely.de>
attempts to set buffered mode was printing out "unable to set buffered
mode" no matter what. Oops.
Spotted by: Joerg Wunsch <joerg_wunsch@uriah.heep.sax.de>
MFC after: 3 weeks
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
Clear residual counts after a successful samount (the user doesn't
care that we got an N-kbyte residual on our test read).
Change a lot of error handling code.
1. If we end up in saerror, check more carefully about the kind of
error. If it is a CAM_SCSI_STATUS_ERROR and it is a read/write
command, we'll be handling this in saerror. If it isn't a read/write
command, check to see whether this is just an EOM/EOP check condition-
if it is, just set residual and return normally. A residual and
then a NO SENSE check condiftion with the ASC of 0 and ASCQ of
between 1 and 4 are normal 'signifying' events, not errors per se,
and we shouldn't give the command to cam_periph_error to do something
relatively unpredictable with.
2. If we get a Bus Reset, had a BDR sent, or get the cam status of
CAM_REQUEUE_REQ, check the retry count on the command. The default
error handler, cam_periph_error, doesn't honor retry count in these
cases. This may change in the future, but for now, make sure we
set EIO and return without calling cam_periph_error if the retry
count for the command with an error is zero.
3. Clean up the pending error case goop and handle cases more
sensibly.
The rules are:
If command was a Write:
If we got a SSD_KEY_VOLUME_OVERFLOW, the resid is
propagated and we set ENOSPC as the error.
Else if we got an EOM condition- just mark EOM pending.
And set a residual of zero. For the longest time I was just
propagating residual from the sense data- but my tape
comparison tests were always failing because all drives I
tested with actually *do* write the data anyway- the EOM
(early warning) condition occurred *prior* to all of the
data going out to media- that is, it was still buffered by
the drive. This case is described in SCSI-2, 10.2.14,
paragraph #d for the meaning of 'information field'. A
better fix for this would be to issue a WFM command of zero
to cause the drive to flush any buffered data, but this
would require a fairly extensive rewrite.
Else if the command was a READ:
If we got a SSD_KEY_BLANK_CHECK-
If we have a One Filemark EOT model- mark EOM as pending,
otherwise set EIO as the erorr.
Else if we found a Filemark-
If we're in Fixed Block mode- mark EOF pending.
If we had an ILI (Incorrect Length Indicator)-
If the residual is less than zero, whine about tape record
being too big for user's buffer, otherwise if we were in
Fixed Block mode, mark EIO as pending.
All 'pending' conditions mean that the command in question completes
without error indication. It had succeeded, but a signifying event
occurred during its execution which will apply to the *next* command
that would be exexcuted. Except for the one EOM case above, we always
propagate residual.
Now, way back in sastart- if we notice any of the PENDING bits set,
we don't run the command we've just pulled off the wait queue. Instead,
we then figure out it's disposition based upon a previous command's
association with a signifying event.
If SA_FLAG_EOM_PENDING is set, we don't set an error. We just complete
the command with residual set to the request count (not data moved,
but no error). We continue on.
If SA_FLAG_EOF_PENDING- if we have this, it's only because we're in
Fixed Block mode- in which case we traverse all waiting buffers (which
we can get in fixed block mode because physio has split things up) and
mark them all as no error, but no data moved and complete them.
If SA_FLAG_EIO_PENDING, just mark the buffer with an EIO error
and complete it.
Then we clear all of the pending state bits- we're done.
MFC after: 4 weeks
Handle both old and new TARGIOALLOCUNIT/TARGIOFREEUNIT cases- the new
one allows us to specify inquiry data we want to use.
Handle more of the CAM_DIS_DISCONNECT case.
Move TARGCTLIOALLOCUNIT to OTARGCTLIOALLOCUNIT, TARGCTLIOFREEUNIT
to OTARGCTLIOFREEUNIT and redefine old associated structure to be
old_ioc_alloc_unit- deprecation but preservation of binaries.
Add new structure for same- but this one contains a pointer to
user defined INQUIRY data so you can define what the target
device looks like to the outside world.
1. If we get frozen, unfreeze for disable disconnects.
2. Put CAM_DIS_DISCONNECT commands at the head of the work queue
(we have a target still connected and we can't run anything else
until this command completes).
If we had an error sending the last CTIO, unfreeze the queue anyway.
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
This is useful if you want to dynamically move into a Fibre Channel
or Multi-initiator environment that happens to be particularly noisy
and ugly that requires a lot of retries (with shorter I/O timeouts)
for commands destried by LIPs or Bus Resets.
Reviewed by: deafening silence on audit && scsi on the retry counts
MFC after: 2 weeks
1. Add SA_IO_TIMEOUT as an option (4 minutes default) to cover reads,
writes, wfm, test unit ready.
2. Add internal SCSIOP_TIMEOUT (e.g., for mode sense) at 1 minute. This
should not require an option, but is cleaner to parameterize.
MFC after: 1 week
- Replace some very poorly thought out API hacks that should have been
fixed a long while ago.
- Provide some much more flexible search functions (resource_find_*())
- Use strings for storage instead of an outgrowth of the rather
inconvenient temporary ioconf table from config(). We already had a
fallback to using strings before malloc/vm was running anyway.
drivers.
- change daprevent() to set CAM_RETRY_SELTO and SF_RETRY_UA when it calls
cam_periph_runccb().
- change the pt(4) driver to ignore unit attentions
- change the targ(4) driver to retry selection timeouts
- clean up a few formatting glitches in the targ(4) driver
Reviewed by: gibbs
prevent scsi_sense_desc() from deferencing a NULL pointer when a drive
happens to return one of these sense keys.
Reported by: Michael Samuel <michael@miknet.net>
With the recent changes in the CAM error handling, some problems in
the error handling of sa(4) have been uncovered. Basically, a number
of conditions that are not actually errors have been mistreated as
genuine errors. In particular:
. Trying to read in variable length mode with a mismatched blocksize
between the on-tape (virtual) blocks and the read(2) supplied buffer
size, causing an ILI SCSI condition, have caused an attempt to retry
the supposedly `errored' transfer, causing the tape to be read
continuously until it eventually hit EOM. Since by default any
simple mt(1) operation does an initial test read, an `mt stat' was
sufficient to trigger this bug.
Note that it's Justin's opinion that treating a NO SENSE as an EIO
is another bug in CAM. I feel not authorized to fix cam_periph.c
without another confirmation that i'm on the right track, however.
. Hitting a filemark caused the read(2) syscall to return EIO, instead
of returning a `short read'. Note that the current fix only solves
this problem in variable length mode. Fixed length mode uses a
different code path, and since i didn't grok all the intentions behind
that handling, i did not touch it (IOW: it's still broken, and you get
an EIO upon hitting a filemark).
The solution is to keep track of those conditions inside saerror(),
and upon completion to not call cam_periph_error() in that case. We
need to make sure that the device gets unfrozen if needed though (in
case of actual errors, cam_periph_error() does this on our behalf).
Not objected by: mjacob (who currently doesn't have the time to
review the patch)
bcopy would go off the end of the array by two elements, which sometimes
causes a panic if it happens to cross into a page that isn't mapped.
Submitted by: gibbs
Reviewed by: peter
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
inq_len member of the ccb_getdev structure, but we've never filled that
value in..
So we now get the length from the inquiry data returned by the drive.
(Since we will fetch as much inquiry data as the drive claims to support.)
Reviewed by: mjacob
Reported by: Andrzej Tobola <san@iem.pw.edu.pl>
offset is set to 0.
Re-arrange the DT limiting code so that we don't end up setting the period
to 0xa if the user really wants async. The previous behavior seemed to
confuse the aic(4) driver.
PR: kern/22733
Reviewed by: gibbs
o Offset and period in synch messages and width negotiation should be
done for per target not per lun. Move these from *lun_info to
*targ_info.
o Change in handling XPT_RESET_DEV and XPT_GET_TRAN_SETTINGS .
o Change CAM_* xpt_done return values.
o Busy loop did not timeout. Change this to timeout as original NetBSD/pc98.
Reviewed by: bsd-nomads ML
not be retried. It is an indication that there was an error that was
corrected during the execution of the command. This is per ANSI SCSI2
spec.
It's possible that these should also be noted to the console (as indicative,
perhaps, of growing media defect lists in drives), but the default of
printing errors out if bootverbose in this case is probably enough.
Also, there'd been a missing ERESTART for that clause anyway.
2. If you have an ABORTED COMMAND, it's almost invariably a SCSI parity
error. You should never be silent about these since users should do something
about this if it occurs (moving that power cord *away* from the SCSI cable is
always a good first start). This should print irrespective of bootverbose
because it's an actual real error even if we retry a transmission.
Reviewed by: audit@freebsd.org, gibbs@freebsd.org
- Use swi_* function names.
- Use void * to hold cookies to handlers instead of struct intrhand *.
- In sio.c, use 'driver_name' instead of "sio" as the name of the driver
lock to minimize diffs with cy(4).
folks.
My guess is that reducing the number of tags is just masking the real
problem for the PR submitter. I'll re-open the PR and see if I can work
with the submitter to diagnose the problem.
PR: 21139
we *really* are.
It should be noted that there is a degenerate case where soft tape
location will be lost (not causing a frozen state- but causing
the loss of reporting fileno/blockno)- that's where you backspace
over a filemark- you stop backspacing as soon as you cross the
filemark, but you have no idea what the record number now is because
you have no idea how many records you are into the file you just
backed into. Such is life.
While I'm at it, also pick up residuals from writing filemarks.
PR: 24222
only CCB type but also extra flags- one of which can be "position
updated".
In other changes: Add in a SA_QUIRK_NO_CPAGE quirk so that it's possible
to avoid using a (broken) device's implementation of he DEVICE COMPRESSION
page.
Also do a couple of printout cleanups.
As per some discussion on FreeBSD-scsi, skip doing tape flushing
if we're reading tape logical block location (MTIOCRDSPOS).
MS will be treated as having this quirk. In the event that we falsely
identify one that doesn't need it, no harm will be done. Ken
suggested that we make this more generic since there may be more
needed in the future.
Reported by: TERAMOTO Masahiro <teramoto@comm.eng.osaka-u.ac.jp>
PR: kern/23378
Reviewed by: ken
field in CDB' error when attempting to start a caddy-type CD drive,
since those drives apparently in general refuse to load a medium. Since
we never advertised the feature to load the medium upon calling
cdstartunit() (i. e. upon receipt of a CDIOCSTART ioctl command), nobody
should have relied on it. Besides, nobody noticed so far at all that
this command is failing for caddy-type drives... Only few applications
seem to use it at all (among them is workman, which made me notice it).
Reviewed by: ken
CDs.
With audio CDs, you can't just do a READ(10) call on most drives without
first setting the blocksize with a mode select command. The disklabel code
does a read of the first sector of the media to find a label if it exists.
This caused drives to return an error when an audio CD was in the drive,
due to the problem described above.
The solution is to read the table of contents on the CD, and only attempt
to read the disklabel if the first track is a data track.
This works on all the various CD and DVD media I have tried, but further
testing (especially with Video CDs and other mode 2 media) will be
needed to determine if this is a universal solution.
Return ENOTSUP for any opcode that is not supported by the XPT
device.
Add back a missing local declaration that seems to have been deleted
by my last commit.
The XPT uses this to prevent tags from being used on parallel SCSI
interfaces immediately after a bus reset or BDR so that controllers
have an oportunity to renegotiate without tag messages in the way.
Somehow this got disabled... the functionality has been here for
quite some time.
Noticed by: my SCSI bus analyzer
This allows writing to DVD-RAM, PD and similar drives that probe as CD
devices. Note that these are randomly writeable devices, not
sequential-only devices like CD-R drives, which are supported by cdrecord.
Add a new flag value for dsopen(), DSO_COMPATLABEL. The cd(4) driver now
uses this flag instead of the DSO_NOLABELS flag. The DSO_NOLABELS always
used a "fake" disklabel for the entire disk, provided by the caller.
With the DSO_COMPATLABEL flag, dsopen() will first search the media for a
label, and if it finds a label, it will use that label. Otherwise it will
use the fake disklabel provided by the caller. This provides backwards
compatibility, since we will still have labels for ISO9660 media.
It also provides new functionality, since you can now have a regular BSD
disklabel on read-only media, or on writeable media (e.g. DVD-RAM).
Bruce and I both think that we should eventually (in a few years) get
away from using disklabels for ISO9660 media, and just use the whole disk
device (/dev/cd0). At that point disklabel handling in the cd(4) driver
could follow the "normal" model, as used in the da(4) driver.
Also, clean up the path in a couple of places in cdregister(). (Thanks to
Nick Hibma for catching that bug.)
Reviewed by: bde
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.
Submitted by: cp
(a NetBSD port for NEC PC-98x1 machines). They are ncv for NCR 53C500,
nsp for Workbit Ninja SCSI-3, and stg for TMC 18C30 and 18C50.
I thank NetBSD/pc98 and bsd-nomads people.
Obtained from: NetBSD/pc98
write caching is disabled on both SCSI and IDE disks where large
memory dumps could take up to an hour to complete.
Taking an i386 scsi based system with 512MB of ram and timing (in
seconds) how long it took to complete a dump, the following results
were obtained:
Before: After:
WCE TIME WCE TIME
------------------ ------------------
1 141.820972 1 15.600111
0 797.265072 0 65.480465
Obtained from: Yahoo!
Reviewed by: peter
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
also mention the peripheral name, bus, target and lun of the device we
attempted to put in that slot. This gives the user a little more
information about what is going on.
Tested by: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Discussed with: gibbs
for the Quantum "MAVERICK 540S" and "LPS525S".
Also, add common string variables, since we seem to have a few Quantum and
Micropolis drives in here.
Fix the 'quantum' variable usage in scsi_all.c that likely got broken when
someone staticized things in cam_xpt.c. (That particular problem would
cause Quantum Fireball ST drives to not get spun up if they were not
already spinning.)
Submitted by: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
to be obeying the original spec as to what the numeric value means.
Temperature flags are unaffected- these are still the 'pseudo-thermometers'
and overtemp/undertemp warnings will be caught and translated to SES objects
here.
PR: 20475
related patches. These include:
* Mode page editting can be scripted. This involves two
things: first, if stdin is not a tty, changes are read from
stdin rather than invoking $EDITOR. Second, and more
importantly, not all modepage entries must be included in the
change set. This means that camcontrol can now gracefully handle
more intrusive editting from the $EDITOR, including removal or
rearrangement of lines. It also means that you can do stuff
like:
# echo "WCE: 1" | camcontrol modepage da3 -m 8 -e
# newfs /dev/da3
# echo "WCE: 0" | camcontrol modepage da3 -m 8 -e
* Range-checking on user-supplied input values. modeedit.c now
uses the field width specifiers to determine the maximum
allowable value for a field. If the user enters a value larger
than the maximum, it clips the value to the max and warns the
user. This also involved patching cam_cmdparse.c to be more
consistent with regards to the "count" parameter to arg_put
(previously is was the length of strings and 1 for all integral
types). The cam_cdbparse(3) man page was also updated to reflect
the revised semantics.
* In the process, I removed the 64 entry limit on mode pages (not
that we were even close to hitting that limit). This was a nice
side-effect of the other changes.
* Technically, the new mode editting functionality allows editting
of character array entries in mode pages (type 'c' or 'z'),
however since buff_encode doesn't grok them it is currently
useless.
* Camcontrol gained two new options related to mode pages: -l and
-b. The former lists all available mode pages for a given
device. The latter forces mode page display in binary format
(the default when no mode page definition was found in
scsi_modes).
* Added support for mode page names to scsi_modes. Allows names to
be displayed alongside mode numbers in the mode page
listing. Updated scsi_modes to use the new functionality. This
also adds the semicolon into the scsi_modes syntax as an
optional mode page definition terminator. This is needed to name
pages without providing a page format definition.
* Updated scsi_all.h to include a structure describing mode page
headers.
* Added $FreeBSD$ line to scsi_modes.
Inspired by: dwhite
Reviewed by: ken
Clean up the comments related to the high speed
sync rate table for SPI.
scsi_message.h:
Bring in some SCSI3 message terminology. All SCSI2 names
are still preserved for backwards compatibility.
Bring back the CAM_NEGOTIATE ccb flag. This flag indicates
that SPI transfer negotiation should occur concurrently with the
execution of this CCB. The flag is not yet used by the XPT but
is required for proper support of multi-initiator configurations
where topology scans cannot rely on a bus reset to invalidate
prior negotiations.
cam_xpt.c:
Don't allow DT transmission rates to be specified for devices
that don't have the DT feature listed in their inquiry data.
CAM_TAG_ACTION_VALID and CAM_DIR_MASK). Remove redundant
CAM_DEBUG line. Spiff up CAM_DEBUG printout for commands
and move the printout up to the top where we can see it,
even for the pending_ua/pending_ca cass. Add missing
newline in a CAM_DEBUG.
to splx(s) if cam_extend_get fails and we return ENXIO, reset ccb flags
when we push ATIOs back to the SIM, do some data increment fixes, set
priority of command based on whether CAM_DIS_DISCONNECT is set and related
changes).
Add in some more CAM_DEBUG_PERIPH debug statements and also add in support
for TARGIODEBUG which then will enable or disable CAM_DEBUG_PERIPH tracing
for an instance.
