components. This is generally considered a non-optimal solution but
it gets the job done for the /rescue case.
Submitted by: Tim Kientzle <kientzle@acm.org>
Change execvp to be a wrapper around execvP. This is necessary for some
of the /rescue pieces. It may also be more generally applicable as well.
Submitted by: Tim Kientzle <kientzle@acm.org>
Approved by: Silence on arch@
bit in the EEPROM mode register on. Also, the address must be written
in two 32-bit register accesses instead of 6 8-bit accesses.
Tested with my 8139B cardbus NIC.
PR: kern/35900
Submitted by: Mark Kettenis <kettenis@chello.nl>
implementation and the new improved one. We now precompute the
signal set passed to sigtimedwait, using an inverted set when
necessary for compatibility with older kernels.
network interfaces could only be turned on and off as a group (all
static interfaces or all dhcp interfaces).
When used to start the interface a 'long form' ifconfig output is
used to show the status of the interface, but when stopping an interface
the script will simply output the name of the interface. This is simply my
personal preference. Hopefully as this functionality matures we can
stabilize on a prefered form of output for these scripts.
A stop command to the dhclient script now explicitly releases the dhcp lease.
Behaviour at system shutdown; however, is unchanged since dhclient is not,
by default, run at that time. The client will not release its lease
at shutdown.
o Ensure rc.d/network2 and rc.d/network3 are not automatically run
during boot
o Modify script headers so rcorder(8) can put the two scripts in the
correct sequence.
o Change the provider names.
o Separate routing into two parts: static routing and routing options. The
start command will run both parts, but they can be run separately using
the static and options command, respectively:
(/etc/rc.d/routing static; /etc/rc.d/routing options)
the user requests a read-only mount. This is necessary because we
don't do the VOP_OPEN again if they upgrade a read-only mount to
read-write.
Fixes lockup when creating files on msdosfs mounts that have been
mounted read-only then upgraded to read-write. The exact cause of
the lockup is not known, but it is likely to be the kernel getting
stuck in an infinite loop trying to write dirty buffers to a device
without write permission.
Reported/tested by andreas, discussed with phk.
mapped I/O mode, we pause for .1 seconds after issuing the reset command
before trying to poll the 'command busy' bit in the status register.
With my 3c575C cardbus NIC, my Sony Picturebook locks up when it tries
to read the status register immediately after the reset. This appears
to be a problem only with certain NICs on certain hardware, but the
added delay should not hurt cards that already work.
This bug seems to have been brought to light by the fact that the xl
driver now defaults to memory mapped I/O mode instead of programmed
I/O mode like it used to. With PIO mode, the delay isn't needed and
everything works (which is why this NIC worked with 5.0-RELEASE but
not 5.1). I suspect that what's happening is that when the chip is
reset, it takes a little while for the memory-mapped decoding logic
to recover. Trying to access the chip's registers during this period
causes an error condition of some kind that wedges the system.
exit function has invalidated the need for _spin[un]lock_pthread().
The _spin[un]lock() functions can now dereference curthread without
the danger that the ldtentry containing the pointer to the thread
has been cleared out from under them.
1.) Handle maximum segment sizes which are smaller than the IOMMU page
size by splitting up pages across multiple segments if needed; this case
was previously unimplemented, and would cause panics.
2.) KASSERT that the physical address is in range; remove a KASSERT that
has become pointless.
3.) Add a comment describing what remains to be fixed in the IOMMU code;
I plan to address these issues soon.
Desired by: dwhite (1)
happens to work on 32-bit platforms as sizeof(long)=sizeof(int), but
wrecks all kinds of havoc (garbage reads, corrupting writes and
misaligned loads/stores) on 64-bit architectures.
The fix for now is to use fuword32() and suword32() and change the
type of the applicable int fields to int32. This is to make it
explicit that we depend on these fields being 32-bit. We may want
to revisit this later.
Reviewed by: deischen
the VMIN and VTIME members of the c_cc array. These members are not
special control characters. By not excluding these members we
changed the noncanonical mode input processing when both members
were 0 on entry (=LINUX_POSIX_VDISABLE) as we would remap them to 255
(=_POSIX_VDISABLE). See termios(4) case A for how that screws up
your terminal I/O.
PR: 23173
Originator: Bjarne Blichfeldt <bbl@dk.damgaard.com>
Patch by: Boris Nikolaus <bn@dali.tellique.de> (original submission)
Philipp Mergenthaler <philipp.mergenthaler@stud.uni-karlsruhe.de>
Reminders by: Joseph Holland King <gte743n@cad.gatech.edu>
MFC after: 5 days
