"skimming thru" the printcap file looking for some common mistakes that
people make. These are the kinds of mistakes where the printcap file
probably looks correct to human eyes, but is wrong in some subtle way
which causes a problem in some queue definitions. The program treats
these as "warnings" not "errors".
Note that I'm flexible on the m.f.c. schedule, if people would rather
this waited until after 4.5-release.
Reviewed by: no screams from freebsd-audit freebsd-print@bostonradio.org
MFC after: 4 days
. The main device node now supports automatic density selection for
commonly used media densities. So you can stuff your 1.44 MB and
720 KB media into your drive and just access /dev/fd0, no questions
asked. It's all that easy, isn't it? :)
. Device density handling has been completely overhauled. The old way
of hardwired kernel density knowledge is no longer there. Instead,
the kernel now implements 16 subdevices per drive. The first
subdevice uses automatic density selection, while the remaining 15
devices are freely programmable. They can be assigned an arbitrary
name of the form /dev/fd[:digit]+.[:digit:]{1,4}, where the second
number is meant to either implement device names that are mnemonic
for their raw capacity (as it used to be), or they can alternatively
be created as "anonymous" devices like fd0.1 through fd0.15,
depending on the taste of the administrator. After creating a
subdevice, it is initialized to the maximal native density of the
respective drive type, so it needs to be customized for other
densities by using fdcontrol(8). Pseudo-partition devices (fd0a
through fd0h) are still supported as symlinks.
. The old hack to use flags 0x1 to always assume drive 0 were there is
no longer supported; this is now supposed to be done by wiring the
devices down from the loader via device flags. On IA32
architectures, the first two drives are looked up in the CMOS
configuration records though. On PCMCIA (i. e., the Y-E Data
controller of the Toshiba Libretto), a single drive is always
assumed.
. Other specialities like disabling the FIFO and not probing the drive
at boot-time are selected by per-controller or per-drive flags, too.
. Unit attentions (media has been changed) are supposed to be detected
now; density autoselection only occurs after a unit attention. (Can
be turned off by a per-drive flag, this will cause each Fdopen() to
perform the autoselection.)
. FM floppies can be handled now (on controllers that actually support
it -- not all do these days).
. Fdopen() can be told to avoid density selection by setting
O_NONBLOCK; this leaves the descriptor in a half-opened state where
only a few ioctls are accepted. This is necessary to run fdformat
on a device that uses automatic density selection (since you cannot
autoselect on an unformatted medium, obviously).
. Just differentiate between a plain old NE765 and the enhanced chips,
but don't try more; the existing code was wrong and only misdetected
the chips anyway.
BUGS and TODOs:
. All documentation update still needs to be done.
. Formatting not-so-standard format yields unpredictable results; i
have yet to figure out why this happens. "Standard" formats like
720 and 1440 KB do work, however.
. rc scripts are needed to setup device nodes with nonstandard
densities (like the old /dev/fdN.MMM we used to have).
. Obtaining device flags from the kernel environment doesn't work yet,
thus currently only drives that are present in (IA32) CMOS are
really detected. Someone who knows the odds and ends about device
flags is needed here, i can't figure out what i'm doing wrong.
. 2.88 MB still needs to be done.
It tries to comply with the SCD 2.4.1 (and thus Sparc 64-bit psABI).
This is an amalgamation of the FreeBSD Alpha crt1.c and the BSD/OS Sparc
crt0.c (which the copyright reflects).
of mi_switch:
- Set the oncpu value for the current thread.
- Always set switchticks, not just in the SMP case.
- Add a KTR entry for fork_exit that is the same as the "new proc"
entry in mi_switch().
- Release sched_lock a bit later like we do with mi_switch().
select/poll, and therefore with pthreads. I doubt there is any way
to make this 100% semantically identical to the way it behaves in
unthreaded programs with blocking reads, but the solution here
should do the right thing for all reasonable usage patterns.
The basic idea is to schedule a callout for the read timeout when a
select/poll is done. When the callout fires, it ends the select if
it is still in progress, or marks the state as "timed out" if the
select has already ended for some other reason. Additional logic in
bpfread then does the right thing in the case where the timeout has
fired.
Note, I co-opted the bd_state member of the bpf_d structure. It has
been present in the structure since the initial import of 4.4-lite,
but as far as I can tell it has never been used.
PR: kern/22063 and bin/31649
MFC after: 3 days
Fair Queueing) and RED (Random Early Detection) to both give the reader
a hint what they are and to make it easier to find out more information
about them.
Now that we've increased the size of our send / receive buffers, bursting
an entire window onto the network may cause congestion. As a result,
we will slow start beginning with a flightsize of 4 packets.
Problem reported by: Thomas Zenker <thz@Lennartz-electronic.de>
MFC after: 3 days
Non-SMP, i386-only, no polling in the idle loop at the moment.
To use this code you must compile a kernel with
options DEVICE_POLLING
and at runtime enable polling with
sysctl kern.polling.enable=1
The percentage of CPU reserved to userland can be set with
sysctl kern.polling.user_frac=NN (default is 50)
while the remainder is used by polling device drivers and netisr's.
These are the only two variables that you should need to touch. There
are a few more parameters in kern.polling but the default values
are adequate for all purposes. See the code in kern_poll.c for
more details on them.
Polling in the idle loop will be implemented shortly by introducing
a kernel thread which does the job. Until then, the amount of CPU
dedicated to polling will never exceed (100-user_frac).
The equivalent (actually, better) code for -stable is at
http://info.iet.unipi.it/~luigi/polling/
and also supports polling in the idle loop.
NOTE to Alpha developers:
There is really nothing in this code that is i386-specific.
If you move the 2 lines supporting the new option from
sys/conf/{files,options}.i386 to sys/conf/{files,options} I am
pretty sure that this should work on the Alpha as well, just that
I do not have a suitable test box to try it. If someone feels like
trying it, I would appreciate it.
NOTE to other developers:
sure some things could be done better, and as always I am open to
constructive criticism, which a few of you have already given and
I greatly appreciated.
However, before proposing radical architectural changes, please
take some time to possibly try out this code, or at the very least
read the comments in kern_poll.c, especially re. the reason why I
am using a soft netisr and cannot (I believe) replace it with a
simple timeout.
Quick description of files touched by this commit:
sys/conf/files.i386
new file kern/kern_poll.c
sys/conf/options.i386
new option
sys/i386/i386/trap.c
poll in trap (disabled by default)
sys/kern/kern_clock.c
initialization and hardclock hooks.
sys/kern/kern_intr.c
minor swi_net changes
sys/kern/kern_poll.c
the bulk of the code.
sys/net/if.h
new flag
sys/net/if_var.h
declaration for functions used in device drivers.
sys/net/netisr.h
NETISR_POLL
sys/dev/fxp/if_fxp.c
sys/dev/fxp/if_fxpvar.h
sys/pci/if_dc.c
sys/pci/if_dcreg.h
sys/pci/if_sis.c
sys/pci/if_sisreg.h
device driver modifications
A similar thing has been in -stable for weeks and is completely safe.
This has very good performance implications as it saves some data
copying, and sometimes avoids triggering performance bugs in devices
(such as the "dc" and other Tulip clones) which do not like scattered
data.
