- Add "fdt addr" subcommand that lets you specify preloaded blob address
- Do not pre-initialize blob for "fdt addr"
- Do not try to load dtb every time fdt subcommand is issued,
do it only once
- Change the way DTB is passed to kernel. With introduction of "fdt addr"
actual blob address can be not virtual but physical or reside in
area higher then 64Mb. ubldr should create copy of it in kernel area
and pass pointer to this newly allocated buffer which is guaranteed to work
in kernel after switching on MMU.
- Convert memreserv FDT info to "memreserv" property of root node
FDT uses /memreserve/ data to notify OS about reserved memory areas.
Technically it's not real property, it's just data blob, sequence
of <start, size> pairs where both start and size are 64-bit integers.
It doesn't fit nicely with OF API we use in kernel, so in order to unify
thing ubldr converts this data to "memreserve" property using the same
format for addresses and sizes as /memory node.
disk_open(). Very often this is called several times for one file.
This leads to reading partition table metadata for each call. To
reduce the number of disk I/O we have a simple block cache, but it
is very dumb and more than half of I/O operations related to reading
metadata, misses this cache.
Introduce new cache layer to resolve this problem. It is independent
and doesn't need initialization like bcache, and will work by default
for all loaders which use the new DISK API. A successful disk_open()
call to each new disk or partition produces new entry in the cache.
Even more, when disk was already open, now opening of any nested
partitions does not require reading top level partition table.
So, if without this cache, partition table metadata was read around
20-50 times during boot, now it reads only once. This affects the booting
from GPT and MBR from the UFS.
The generic ELF loading code maps the kernel into low memory
by subtracting KERN_BASE. So the copyin/copyout/readin functions
are always called with low addresses. This code finds the largest
DRAM block from the U-Boot memory map and adds that base to
the addresses.
In particular, this fixes ubldr on AM3358, which has DRAM
mapped to 0x80000000 at power-on.
The code previously assumed that copyin/copyout did no
address translation and that the device tree blob could
be manipulated in-place (with only a few adjustments for
the ELF loader offset). This isn't possible on all platforms,
so the revised code uses copyout() to copy the device tree
blob into a heap-allocated buffer and then updates the
device tree with copyout(). This isn't ideal, since it
bloats the loader memory usage, but seems the only feasible
approach (short of rewriting all of the fdt manipulation
routines).
Enable using the statically embedded blob from the kernel, if present. The KLD
loaded DTB takes precedence, but they are both recognized and handled in the
same way.
Submitted by: Lukasz Wojcik
Obtained from: Semihalf
MFC after: 1 week
o This is disabled by default for now, and can be enabled using WITH_FDT at
build time.
o Tested with ARM and PowerPC.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
- Only non-sliced bsdlabel style partitioning is currently supported (but provisions
are made towards GPT support, which should follow soon)
- Enable storage support in loader on ARM
Obtained from: Semihalf
This uses the common U-Boot support lib (sys/boot/uboot, already used on
FreeBSD/powerpc), and assumes the underlying firmware has the modern API for
stand-alone apps enabled in the config (CONFIG_API).
Only netbooting is supported at the moment.
Obtained from: Marvell, Semihalf
- extend ub_dev_read() and ub_dev_recv() so that the actual len and
all error codes can be passed and processed properly; unify behaviour of
these routines
- introduce syscall general error code (API_ESYSC)
- add new diag commands: devinfo, sysinfo for U-Boot-style details about the system
configuration
- better memory info summary
- style corrections
Obtained from: Semihalf
- It is opt-out for now so as to give it maximum testing, but it may be
turned opt-in for stable branches depending on the consensus. You
can turn it off with WITHOUT_SSP.
- WITHOUT_SSP was previously used to disable the build of GNU libssp.
It is harmless to steal the knob as SSP symbols have been provided
by libc for a long time, GNU libssp should not have been much used.
- SSP is disabled in a few corners such as system bootstrap programs
(sys/boot), process bootstrap code (rtld, csu) and SSP symbols themselves.
- It should be safe to use -fstack-protector-all to build world, however
libc will be automatically downgraded to -fstack-protector because it
breaks rtld otherwise.
- This option is unavailable on ia64.
Enable GCC stack protection (aka Propolice) for kernel:
- It is opt-out for now so as to give it maximum testing.
- Do not compile your kernel with -fstack-protector-all, it won't work.
Submitted by: Jeremie Le Hen <jeremie@le-hen.org>
This was introduced as a workaround long time ago for some Alpha firmware
(which is now gone), and actually prevented net_close() to ever be
called.
Certain firmwares (U-Boot) need local shutdown operations to be performed on a
network controller upon transaction end: such platform-specific hooks are
supposed to be called via netif_close() (from within net_close()).
This change effectively reverts the following CVS commit:
sys/boot/common/dev_net.c
revision 1.7
date: 2000/05/13 15:40:46; author: dfr; state: Exp; lines: +2 -1
Only probe network settings on the first open of the network device.
The alpha firmware takes a seriously long time to open the network device
the first time.
Also suppress excessive output while netbooting via loader, unless debugging.
While there, make sys/boot/uboot more style(9) compliant.
Reviewed by: imp
Approved by: cognet (mentor)
