is on the MacIO ones. It appears to be unreliable on all DBDMA-based
controllers for unknown reasons, which should be figured out eventually.
Tested by: Torfinn Ingolfsen
MFC after: 1 week
zpool the output causes the script to bail out with syntax errors.
Since a scrub of a faulted zpool is pointless, just skip over any pools
marked as such.
PR: conf/150228
Submitted by: jpaetzel
Approved by: kib (mentor)
MFC after: 3 days
MFC note: only for RELENG_8
The linux ath9k driver and (from what I've been told) the atheros reference
driver does this; it then leaves discarding 11n frames to the 802.11 layer.
Whilst I'm here, merge in a fix from ath9k which maintains a turbo register
setting when enabling the 11n register; and remove an un-needed (duplicate)
flag setting.
It does not make sense to shut down daemons that were not started. In
particular, this fixes loss of mixer settings when shutting down using
shutdown(8), init(8) or ctrl+alt+del from single-user mode.
If /etc/rc reboots, /etc/rc.shutdown is not run.
Also fix segfaults and other erratic behaviour if init receives SIGHUP or
SIGTSTP while in single-user mode.
This commit does not attempt to fix any badness with signal handlers
(assumption that pointers can be read and written atomically, EINTR race
condition). I believe it does not make this badness any worse.
Silence on: -arch@
write to the buffer causes it to overflow. We therefore can't hold the CC list
rwlock over a call to sbuf_printf() for an sbuf configured with SBUF_AUTOEXTEND.
Switch to a fixed length sbuf which should be of sufficient size except in the
very unlikely event that the sysctl is being processed as one or more new
algorithms are loaded. If that happens, we accept the race and may fail the
sysctl gracefully if there is insufficient room to print the names of all the
algorithms.
This should address a WITNESS warning and the potential panic that would occur
if the sbuf call to malloc did sleep whilst holding the CC list rwlock.
Sponsored by: FreeBSD Foundation
Reported by: Nick Hibma
Reviewed by: bz
MFC after: 3 weeks
X-MFC with: r215166
Fix a long standing bug, where the procs ticks where assumed to be in
us. Instead, read cpu_tick_frequency from the kernel and use the same
logic to convert runtime. This is still too optimistic in that it
assumes cpu_tick_frequency is available and fixed. Since this function
is only called on crashdumps, I think we can live with that. Testing has
shown the values to be correct for different kern.hz inside Virtualbox.
Bump WARNS. Alignment issues on some archs mean this is still at 3.
Reviewed by: bde
- make WARNS=6 clean for archs w/o strict alignment requirments
- add const, ANSIfy, remove unused vars, cast types for comparison
- thanks to differing definitions of VM_MIN_ADDRESS across our archs, we
need to trick the compiler to not complain about signedness. We could
either fix VM_MIN_ADDRESS to always be a simple integer or make the
check conditional on $ARCH.
Closes PRs: kern/42386, kern/83364
Reviewed by: bde
combinations) by forcing FAILFILE into .CURDIR as we do for all other
universe output files. [1] Similarly make FAILFILE start with "_." as well.
Reviewed by: silence-on-src [1]
MFC after: 6 days
by the MBR for the given parameter and set that parameter to the
maximum value instead of just truncating the most significant part
silently.
Could happen for example if the capacity of the device is more
than 2TB, so that the number of sectors is greater than 2Mib.
MFC after: 1 month
defined. The kernel linker doesn't deal with symbols of
type NOTYPE and typically gives the wrong symbol ($a) for
local symbols.
Obtained from: Juniper Networks, Inc.
Because {NGROUPS_MAX} may become variable, its value should be obtained
using sysconf(3). If a #define is used anyway, it should be obtained by
including <limits.h> as that is in POSIX like getgroups(2) itself is.
<sys/param.h> is not in POSIX.
MFC after: 1 week
The v1 and v3 interfaces returned the whole EEPROM but the v14/v4k
interfaces just returned the base header. There's extra information
outside of that which would also be nice to get access to.
The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.
Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.
- The mean RTT is updated at the end of each congestion epoch, but if we switch
to congestion avoidance within the first epoch (e.g. if ssthresh was primed
from the hostcache), we'll trigger a divide by zero panic in
cubic_ack_received(). Set the mean to the min in cubic_record_rtt() if the
mean is less than the min to ensure we have a sane mean for use in this
situation. This fixes the panic reported by Nick Hibma.
- Adjust conditions under which we update the mean RTT in cubic_post_recovery()
to ensure a low latency path won't yield an RTT of less than 1. This avoids
another potential divide by zero panic when running CUBIC in networks with
sub-millisecond latencies.
- Remove the "safety" assignment of min into mean when we don't update the mean
because of failed conditions. The above change to the conditions for updating
the mean ensures the safety issue is addressed and I feel it is better to keep
our previous mean estimate around if we can't update than to revert to the
min.
- Initialise the mean RTT to 1 on connection startup to act as a safety belt if
a situation we haven't considered and addressed with the above changes were to
crop up in the wild.
Sponsored by: FreeBSD Foundation
Reported and tested by: Nick Hibma
Discussed with: David Hayes <dahayes at swin edu au>
MFC after: 5 weeks
X-MFC with: r216114
